component
MIC2860-2DYD6-TR
Public Made by Adomby adom
Microchip Tech Pre-ordered MCUs, TSOT-23-6L. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMIC2860-2DYD6-TR
Microchip Tech · Pre-ordered MCUs · TSOT-23-6L
MIC2860-2DYD6-TR from Microchip Tech, in a TSOT-23-6L. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SC | input | Serial control digital input that acts as the enable for the linear drivers and the single-wire dimming input; VSC must stay between 0V and VIN, with logic low at 0.4V max and logic high at 1.4V min, and the pin must not be left floating. |
| 2 | GND | power_in | Ground path for the linear drivers; the input capacitor ground should be routed with low impedance and kept as short as possible to this pin. |
| 3 | VIN | power_in | Voltage input with an operating range of 3.0V to 5.5V (absolute maximum -0.3V to +6V); connect at least a 1µF ceramic capacitor between VIN and GND. |
| 4 | D2 | output | LED2 driver: connect the LED anode to VIN and the cathode to this pin, with LED2 driver voltage limited to 0V to VIN and the pin not left floating. |
| 5 | RSET | passive | Connect an external resistor from this pin to GND to set the maximum LED current, for example 9.53kΩ gives 30.2mA at 100% duty cycle. |
| 6 | D1 | output | LED1 driver: connect the LED anode to VIN and the cathode to this pin, with LED1 driver voltage limited to 0V to VIN and the pin not left floating. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TSOT-23-6L |
| Category | Embedded Processors & Controllers |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Main Input Voltage | VIN | -0.3 | 6 | V | 3 | ||
| Enable Input Voltage | VSC | -0.3 | V | 3 | |||
| LED Driver Voltage | VD1, D2 | -0.3 | V | 3 | |||
| Lead Temperature (soldering) | 260 | °C | soldering, 10 sec. | 3 | |||
| Storage Temperature | Ts | -65 | 150 | °C | 3 | ||
| Supply Voltage | VIN | 3 | 5.5 | V | 3 | ||
| Enable Input Voltage | VSC | 0 | V | 3 | |||
| LED Driver Voltage | VD1, D2 | 0 | V | 3 | |||
| Junction Temperature | TJ | -40 | 125 | °C | 3 | ||
| Temperature Range (ordering) | -40 | 85 | °C | Temperature range for MIC2860-2DYD6 per Ordering Information | 2 | ||
| Current Accuracy | 27.18 | 30.2 | 33.22 | mA | Average current of all channels in use and all channels loaded (note 4) | 3 | |
| Matching | -3 | 0.5 | 3 | % | Current through each LED from average current of all LEDs (note 5) | 3 | |
| Drop-out (VD1, D2) | VDROP | 52 | 125 | mV | Where ILED = 90% of LED current seen at VDROPNOM = 0.6V, 100% brightness level | 3 | |
| Ground/Supply Bias Current | 0.7 | 1.5 | mA | IOUT = 30.2mA | 3 | ||
| Shutdown Current (current source leakage) | 0.01 | 1 | µA | VSC = 0V > 500µs | 3 | ||
| VSC Input Voltage Logic Low | VSC | 0.4 | V | 3 | |||
| VSC Input Voltage Logic High | VSC | 1.4 | V | 3 | |||
| VSC Enable Input Current | 0.01 | 1 | µA | VSC = 1.2V | 3 | ||
| tSHUTDOWN Time | tSHUTDOWN | 100 | 500 | µs | SC pin is low to put into shutdown | 3 | |
| tPROG_HIGH, tPROG_LOW Time | tPROG_HIGH, tPROG_LOW | 0.3 | 75 | µs | Time for valid SC edge; Ignored if outside limit range | 3 | |
| tSTART_UP Delay | tSTART_UP | 33 | µs | Delay from SC is high to start up | 3 |
CAD (KiCad official)
- Symbol:
MIC2860-2DYD6-TR - Footprint:
Package_TO_SOT_SMD:TSOT-23-6 - 3D model: TSOT-23-6L (KiCad packages3D, STEP)
- 3D model files:
mic2860-2dyd6-tr-etched.step/mic2860-2dyd6-tr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic2860-2dyd6-tr.step/mic2860-2dyd6-tr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (12 pp, sha256
f61f638666578ec6, retrieved 2026-10-25, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).