main
Ray Publish 0.1.0 74cee2b

MIC2800-G1JJYML-TR

Microchip Tech · Power Management Specialized - PMIC · QFN-16(3x3)

MIC2800-G1JJYML-TR from Microchip Tech, in a QFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 LOWQ input LOWQ mode control: logic high (>1V) selects constant-frequency PWM mode, logic low (<0.2V) selects low-noise LOWQ linear mode, and it must not be left floating.
2 BIAS passive Internal bias supply for control and reference circuitry, to be decoupled to signal ground with a 0.1 µF ceramic and not loaded.
3 SGND power_in Signal ground for the biasing and control circuitry; its current loop should be kept as small as possible.
4 PGND power_in Power ground for the high-current PWM mode; its current loop should be kept as small as possible.
5 SW output Switch node connected to the inductor, driven by the internal power MOSFETs; route it away from sensitive nodes because of high-speed switching.
6 VIN power_in DC/DC converter supply input that must be tied externally to pin 7.
7 VIN power_in LDO2 supply input that must be tied externally to pin 6.
8 LDO2 power_out Output of LDO regulator 2, which is 300 mA capable; in LOWQ mode its output load is limited to 10 mA.
9 FB input Feedback input to the DC/DC error amplifier; for fixed output voltages connect it directly to VOUT.
10 LDO power_out Output of the LOWQ-mode linear regulator, connected to the DC/DC output; in LOWQ mode it can deliver 60 mA and limits LDO1 and LDO2 loads to 10 mA.
11 LDO1 power_out Output of LDO regulator 1, whose input power is provided by the DC/DC switching regulator.
12 POR output Open-drain power-on reset output that goes active low on an output undervoltage condition on any of the three regulated outputs.
13 CSET passive Delay set input where a capacitor to GND sets the POR rising delay; it cannot be grounded directly, and leaving it open gives the minimum delay.
14 CBYP passive Reference bypass input where an external 0.1 µF to GND reduces output noise; it may be left open.
15 EN1 input Active-high enable for the DC/DC converter and LDO1; logic high turns them on, logic low turns them off, and it must not be left floating.
16 EN2 input Active-high enable for LDO2 only; logic high turns it on, logic low turns it off, and it must not be left floating.
17 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package QFN-16(3x3)
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage (VIN) VIN -0.3 6 V 3
Supply Voltage (VIN) operating range VIN 2.7 5.5 V 3
Enable Input Voltage (VEN1, EN2) VEN1, EN2 -0.3 V max +(VIN+0.3V) 3
Enable Input Voltage (VEN1, EN2) operating range VEN1, EN2 0 V max +VIN 3
LOWQ, POR voltage LOWQ, POR -0.3 6 V 3
LOWQ, POR voltage operating range LOWQ, POR 0 5.5 V 3
Junction Temperature (TJ) TJ -40 125 °C 3
Storage Temperature (TS) TS -65 150 °C 3
Lead Temperature 260 °C soldering, 10 sec. 3
ESD Rating 2 kV Human body model, 1.5 kΩ in series with 100 pF 3
Junction Thermal Resistance QFN-16 θJA 45 °C/W 16-Ld QFN 3
UVLO Threshold UVLOTH 2.45 2.55 2.65 V Rising input voltage during turn on 4
UVLO Hysteresis UVLOHYS 100 mV 4
Ground Pin Current in Shutdown IGND_SHDN 0.2 5 µA All EN = 0V 4
Overtemperature Shutdown TSD 160 °C 4
Overtemperature Shutdown Hysteresis TSDHYS 23 °C 4
Enable Input Voltage Logic Low VIH 0.2 V 4
Enable Input Voltage Logic High VIL 1 V 4
Enable Input Current IENLK 0.1 1 µA VIL ≤ 0.2V 4
Turn-on Time (DC/DC) tTURN-ON 83 350 µs EN2 = VIN; ILOAD = 300 mA; CBYP = 0.1 µF 4
POR Threshold Voltage, Failing VTHLOW_POR 90 91 % Low Threshold, % of nominal (Flag ON) 4
POR Threshold Voltage, Rising VTHIGH_POR 96 99 % High Threshold, % of nominal (Flag OFF) 4
POR Output Logic Low Voltage VOLPOR 10 100 mV IL = 250 µA 4
Flag Leakage Current ILEAKPOR 0.01 1 µA Flag OFF 4
CSET Pin Current Source ICSET 0.75 1.25 1.75 µA VCSET = 0V 4
CSET Pin Threshold Voltage VTHCSET 1.25 V POR = High 4
Output Voltage Accuracy (DC/DC, LOWQ High) VOUT -2 2 % Fixed Output Voltages 5
Output Voltage Accuracy (DC/DC, LOWQ High, bold range) VOUT -3 3 % bold values, -40°C ≤ TJ ≤ +125°C 5
Current Limit in PWM Mode ILIM 0.75 1 1.6 A VOUT = 0.9*VNOM 5
Output Voltage Line Regulation (∆VOUT/VOUT)/∆VIN 0.2 %/V VOUT > 2.4V; VIN = VOUT + 300 mV to 5.5V, ILOAD= 100 mA 5
Output Voltage Load Regulation ∆VOUT/VOUT 0.2 1.5 % 20 mA < ILOAD < 300 mA 5
Maximum Duty Cycle DCMAX 100 % VFB ≤ 0.4V 5
Oscillator Frequency fosc 1.8 2 2.2 MHz 5
Output Voltage Noise (DC/DC) VN 60 µVRMS COUT = 2.2 µF; CBYP = 0.1 µF; 10 Hz to 100 KHz 5
Output Voltage Accuracy (DC/DC, LOWQ Low) VOUT -2 2 % Variation from nominal VOUT 5
Output Voltage Accuracy (DC/DC, LOWQ Low, -40°C to +125°C) VOUT -3 3 % Variation from nominal VOUT; -40°C to +125°C 5
Output Voltage Temp. Coefficient TCVOUT 40 ppm/C 5
Line Regulation (DC/DC, LOWQ Low) (∆VOUT/VOUT)/∆VIN 0.02 0.3 %/V VIN = VOUT + 1V to 5.5V; IOUT = 100 µA 5
Load Regulation (DC/DC, LOWQ Low) ∆VOUT/VOUT 0.2 1.5 % IOUT = 100 µA to 50 mA 5
Ripple Rejection (DC/DC, LOWQ Low) PSRR 50 dB f = up to 1 kHz; COUT = 2.2 µF; CBYP = 0.1 µF 5
Ripple Rejection (DC/DC, LOWQ Low) PSRR 30 dB f = 20 kHz; COUT = 2.2 µF; CBYP = 0.1 µF 5
Current Limit (DC/DC, LOWQ Low) ILIM_LOWQ 80 120 190 mA VOUT = 0V 5
Output Current Capability (LDO1, VIN ≥ 1.8V) IOUT 300 mA VIN ≥ 1.8V 6
Output Current Capability (LDO1, VIN ≥ 1.5V) IOUT 120 mA VIN ≥ 1.5V 6
Output Voltage Accuracy (LDO1, LOWQ High) VOUT -2 2 % Variation from nominal VOUT 6
Output Voltage Accuracy (LDO1, LOWQ High, -40°C to +125°C) VOUT -3 3 % Variation from nominal VOUT; -40°C to +125°C 6
Current Limit (LDO1, LOWQ High) ILIM 350 500 700 mA VOUT = 0V 6
Ripple Rejection (LDO1, LOWQ High) PSRR 70 dB f = up to 1 kHz; COUT = 2.2 µF; CBYP = 0.1 µF 6
Ripple Rejection (LDO1, LOWQ High) PSRR 44 dB f = 20 kHz; COUT = 2.2 µF; CBYP = 0.1 µF 6
Output Voltage Noise (LDO1) VN 30 µVRMS COUT = 2.2 µF; CBYP = 0.1 µF; 10 Hz to 100 KHz 6
Output Voltage Accuracy (LDO1, LOWQ Low) VOUT -3 3 % Variation from nominal VOUT 6
Output Voltage Accuracy (LDO1, LOWQ Low, -40°C to +125°C) VOUT -4 4 % Variation from nominal VOUT; -40°C to +125°C 6
Current Limit (LDO1, LOWQ Low) ILIM 50 85 125 mA VOUT = 0V 6
Ripple Rejection (LDO1, LOWQ Low) PSRR 70 dB f = up to 1 kHz; COUT = 2.2 µF; CBYP = 0.1 µF 6
Ripple Rejection (LDO1, LOWQ Low) PSRR 42 dB f = 20 kHz; COUT = 2.2 µF; CBYP = 0.1 µF 6
Output Voltage Accuracy (LDO2, LOWQ High) VOUT -2 2 % Variation from nominal VOUT 7
Output Voltage Accuracy (LDO2, LOWQ High, -40°C to +125°C) VOUT -3 3 % Variation from nominal VOUT; -40°C to +125°C 7
Line Regulation (LDO2, LOWQ High) (∆VOUT/VOUT)/∆VIN 0.02 0.3 %/V VIN = VOUT +1V to 5.5V; IOUT = 100 µA 7
Ripple Rejection (LDO2, LOWQ High) PSRR 75 dB f = up to 1 kHz; COUT = 2.2 µF; CBYP = 0.1 µF 7
Ripple Rejection (LDO2, LOWQ High) PSRR 40 dB f = 20 kHz; COUT = 2.2 µF; CBYP = 0.1 µF 7
Current Limit (LDO2, LOWQ High) ILIM 400 550 850 mA VOUT = 0V 7
Output Voltage Noise (LDO2) VN 25 µVRMS COUT = 2.2 µF; CBYP = 0.1 µF; 10 Hz to 100 KHz 7
Output Voltage Accuracy (LDO2, LOWQ Low) VOUT -3 3 % Variation from nominal VOUT 7
Output Voltage Accuracy (LDO2, LOWQ Low, -40°C to +125°C) VOUT -4 4 % Variation from nominal VOUT; -40°C to +125°C 7
Current Limit (LDO2, LOWQ Low) ILIM 50 85 125 mA VIN = 2.7V; VOUT = 0V 7

CAD (KiCad official)

  • Symbol: MIC2800-G1JJYML-TR
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: QFN-16(3x3) (KiCad packages3D, STEP)
  • 3D model files: mic2800-g1jjyml-tr-etched.step / mic2800-g1jjyml-tr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mic2800-g1jjyml-tr.step / mic2800-g1jjyml-tr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (30 pp, sha256 59709361ca877f0a, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF