3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMIC2587R-1YM
Microchip Tech · Monitors & Reset Circuits · SOIC-8
MIC2587R-1YM from Microchip Tech, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | ON | input | Enable input: a start cycle begins when ON is above VONH, below VONL causes undervoltage lockout, and toggling it LOW then HIGH resets the circuit breaker after a fault. |
| 2 | FB | input | Output voltage feedback input from an external resistor divider; PWRGD asserts when FB crosses VFBH (1.313V typ) and de-asserts below VFBL (1.233V typ), with 80mV typical hysteresis, and it also sets the foldback current limit. |
| 3 | PWRGD | output | Active-HIGH open-drain Power-is-Good output (MIC2587R-1) that is high-impedance when FB is above VFBH and pulls to GND when FB is below VFBL, and can work with pull-up supplies up to 100V. |
| 4 | GND | power_in | Ground pin, tied directly to the system's analog GND plane. |
| 5 | TIMER | passive | Current-limit response timer: a capacitor to GND sets the fault time before the breaker trips, and on the MIC2587R it sets the auto-retry period with a fixed nominal 5% duty cycle. |
| 6 | GATE | output | Gate drive output of the internal charge pump for the external N-channel MOSFET, providing at least +7.5V gate drive above VCC (16µA IGATEON pull-up) and pulled low by an 80mA IGATEFLT source on overcurrent faults. |
| 7 | SENSE | input | Circuit breaker sense input (-) Kelvin connection, with RSENSE between this pin and VCC setting the trip point at VTRIP (47mV typ), and tying it to VCC disables the circuit breaker. |
| 8 | VCC | power_in | Positive supply input and (+) Kelvin sense connection, with a +10V to +80V operating range, transients to +100V, and an undervoltage lockout that holds GATE low. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-8 |
| Category | Power Management ICs |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VCC | 10 | 80 | V | 6 | ||
| Ambient Temperature Range | TA | -40 | 85 | °C | Operating ratings | 6 | |
| Supply Current | ICC | 2 | 5 | mA | VON = VFB = 1.5V | 6 | |
| Undervoltage Lockout rising | VUVH | 7.5 | 8 | 8.5 | V | VCC rising | 6 |
| Undervoltage Lockout falling | VUVL | 7 | 7.5 | 8 | V | VCC falling | 6 |
| Feedback Pin Voltage High Threshold | VFBH | 1.28 | 1.313 | 1.345 | V | FB Low-to-High transition | 6 |
| Feedback Pin Voltage Low Threshold | VFBL | 1.208 | 1.233 | 1.258 | V | FB High-to-Low transition | 6 |
| FB Pin Threshold Line Regulation | ∆VFB | -0.05 | 0.05 | mV/V | 10V ≤ VCC ≤ 80V | 6 | |
| FB Pin Input Current | IFB | -1 | 1 | µA | 0V ≤ VFB ≤ 3V | 6 | |
| Circuit Breaker Trip Voltage | VTRIP | 5 | 12 | 17 | mV | VFB = 0V (see Figure 1) | 6 |
| Circuit Breaker Trip Voltage | VTRIP | 39 | 47 | 55 | mV | VFB = 1V (see Figure 1) | 6 |
| MOSFET Gate Drive, VGATE - VCC | ∆VGATE | 7.5 | 18 | V | +10V ≤ VCC ≤ +80V | 6 | |
| GATE Pin Pull-Up Current | IGATEON | -22 | -16 | -10 | µA | Start cycle, VGATE = 7V | 6 |
| GATE Pin rapid pull-down current during fault | IGATEFLT | 30 | 80 | 200 | mA | (VCC − VSENSE) = (VTRIP + 10mV), VGATE = 5V | 6 |
| GATE Pin Turn-off Current | IGATEOFF | 1.8 | mA | Normal turn-off, or from VGATE[TH] (MOSFET) to 0V after a fault condition | 7 | ||
| Timer Pin Charging Current | ITIMERUP | -120 | -65 | -24 | µA | (VCC, VSENSE) > VTRIP, VTIMER = 0V | 7 |
| Timer Pin Pull-Down Current | ITIMERDN | 1.5 | 3.5 | 5 | µA | (VCC, VSENSE) < VTRIP, VTIMER = 0.6V | 7 |
| TIMER Pin High Threshold Voltage | VTIMERH | 1.28 | 1.313 | 1.345 | V | 7 | |
| TIMER Pin Low Threshold Voltage | VTIMERL | 0.4 | 0.49 | 0.6 | V | 7 | |
| ON Pin High Threshold Voltage | VONH | 1.28 | 1.313 | 1.355 | V | ON Low-to-High transition | 7 |
| ON Pin Low Threshold Voltage | VONL | 1.208 | 1.233 | 1.258 | V | ON High-to-Low transition | 7 |
| ON Pin Input Current | ION | 2 | µA | 0V ≤ VON ≤ 80V | 7 | ||
| Power-Good Output Voltage | VOL | 0.4 | V | PWRGD or /PWRGD = LOW, IOL = 1.6mA | 7 | ||
| Power-Good Output Voltage | VOL | 0.8 | V | PWRGD or /PWRGD = LOW, IOL = 4mA | 7 | ||
| Power-Good Leakage Current | IOFF | 10 | µA | PWRGD or /PWRGD = Open-Drain, VPG = VCC, VON = 1.5V | 7 | ||
| Overcurrent Sense to GATE Low Trip Time | tOCSENSE | 1 | 2 | µs | (VCC - VSENSE) = (VTRIP + 10mV), Figure 7 | 7 | |
| Supply Voltage (VCC) | VCC | -0.3 | 100 | V | Referred to GND | 6 | |
| GATE pin | -0.3 | 100 | V | 6 | |||
| ON, SENSE pins | -0.3 | 100 | V | 6 | |||
| PWRGD, /PWRGD pins | -0.3 | 100 | V | 6 | |||
| FB pin | -0.3 | 100 | V | 6 | |||
| TIMER pin | -0.3 | 6 | V | 6 | |||
| Junction Temperature | TJ | 125 | °C | 6 | |||
| Lead Temperature | 260 | °C | Soldering, 10s | 6 | |||
| Storage Temperature | TA | -65 | 150 | °C | 6 | ||
| ESD Rating Human Body Model | 2 | kV | 1.5kΩ in series with 100pF | 6 | |||
| ESD Rating Machine Model | 200 | V | 6 | ||||
| Package Thermal Resistance | θJA | 160 | °C/W | 8-pin SOIC | 6 | ||
| VCC Undervoltage Lockout Hysteresis | VHYSLO | 500 | mV | 6 | |||
| Feedback Voltage Hysteresis | VHYSFB | 80 | mV | 6 | |||
| ON Pin Hysteresis | VHYSON | 80 | mV | 7 | |||
| ON High to GATE High | tPONLH | 3 | ms | CGATE = 10nF | 7 | ||
| ON Low to GATE Low | tPONHL | 1 | ms | VIN = 48V, CGATE = 10nF | 7 | ||
| FB Valid to PWRGD High | tPFBLH | 2 | µs | RPG = 50kΩ pull-up to 48V, CL=100pF | 7 | ||
| FB Invalid to PWRGD Low | tPFBHL | 4 | µs | RPG = 50kΩ pull-up to 48V, CL=100pF | 7 |
CAD (KiCad official)
- Symbol:
MIC2587R-1YM - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOIC-8 (KiCad packages3D, STEP)
- 3D model files:
mic2587r-1ym-etched.step/mic2587r-1ym-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic2587r-1ym.step/mic2587r-1ym.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet, copy hosted by LCSC (22 pp, sha256
2bebc64bbe8a71f7, retrieved 2026-11-20) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).