Generated by kicad-footprint-generator · KiCad file format 20260206
MIC2547-2YTS
Microchip Tech · Power Management Specialized - PMIC · TSSOP-16
MIC2547-2YTS from Microchip Tech, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | INA | power_in | Input A is the output A MOSFET drain and also supplies the internal circuitry. |
| 2 | OUTA | output | Switch A output is the output A MOSFET source and must be externally connected to pin 16. |
| 3 | ENA | input | Enable A is a logic-compatible input with a high input above 1.7V typical and a low input below 1.5V typical; on the MIC2547 it also resets the thermal shutdown latch. |
| 4 | NC | unconnected | Not internally connected. |
| 5 | FLGA | output | Fault Flag A is an active-low open-drain output that indicates overcurrent or thermal shutdown, and on the MIC2547 it is latched low on thermal shutdown. |
| 6 | GNDB | power_in | Ground; this pin must be connected to GND. |
| 7 | ILIMB | passive | Current Limit Channel B sets the current-limit threshold through a resistor RSET to ground, with 154Ω < RSET < 2.29kΩ. |
| 8 | OUTB | output | Switch B output is the output B MOSFET source and must be externally connected to pin 11. |
| 9 | INB | power_in | Input B is the power supply connection to the channel B logic circuitry and the output B MOSFET drain. |
| 10 | NC | unconnected | Not internally connected. |
| 11 | OUTB | output | Switch B output is the output B MOSFET source and must be externally connected to pin 8. |
| 12 | ENB | input | Enable B is a logic-compatible enable input that must be driven high or low and not left floating. |
| 13 | FLGB | output | Fault Flag B is an active-low open-drain output that indicates overcurrent or thermal shutdown, and on the MIC2547 it is latched low on thermal shutdown. |
| 14 | GNDA | power_in | Ground; this pin must be connected to GND. |
| 15 | ILIMA | passive | Current Limit Channel A sets the current-limit threshold through a resistor RSET to ground, with 154Ω < RSET < 2.29kΩ. |
| 16 | OUTA | output | Switch A output is the output A MOSFET source and must be externally connected to pin 2. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TSSOP-16 |
| Category | Power Supply Chip |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply current, switch on (per channel supply; table row) | 200 | 320 | µA | Switch on, OUT = open, Note 4; VIN = 5V, TA = 25°C (bold values -40°C to +85°C) | 4 | ||
| Enable Low input voltage | VEN | 0.8 | V | Enable Low, Note 4 | 4 | ||
| Enable High input voltage | VEN | 2.4 | V | Enable High, Note 4 | 4 | ||
| Enable input current | 0.01 | 1 | µA | VEN = VOH(MIN) = 2.4V | 4 | ||
| Switch resistance (on-resistance) | RDS(ON) | 80 | 120 | mΩ | IOUT = 500mA | 4 | |
| Current limit factor | 184 | 230 | 276 | V | IOUT = 500mA to 1.5A, VOUT = 1.0V to 4.0V, Note 6 (ILIMIT = 230V / RSET) | 4 | |
| Output leakage current | 1 | 10 | µA | Switch off | 4 | ||
| Output turn-on delay | tON | 1 | 2 | 5 | ms | RL = 10Ω, CL = 1µF, Figure 1a and 1b | 4 |
| Output turn-on rise time | tR | 1 | 2 | 5 | ms | RL = 10Ω, CL = 1µF, Figure 1a and 1b | 4 |
| Error flag output resistance | 4 | 15 | Ω | VIN = 5V, IL = 10µA | 4 | ||
| Error flag output resistance | 5 | 20 | Ω | VIN = 3.3V, IL = 10µA | 4 | ||
| Error flag off current | 0.01 | 1 | µA | VFLG = 5V | 4 | ||
| Supply current, switch off | 1.5 | 10 | µA | Switch off, OUT = open, Note 4 | 4 | ||
| Output turn-off fall time | tF | 21 | µs | RL = 10Ω, CL = 1µF, Figure 1a and 1b | 4 | ||
| Output turn-off delay | tOFF | 22 | µs | RL = 10Ω, CL = 1µF, Figure 1a and 1b | 4 | ||
| Enable input capacitance | 1 | pF | Note 5 (guaranteed by design, not production tested) | 4 | |||
| Overtemperature shutdown threshold, TJ increasing | 140 | °C | TJ increasing | 4 | |||
| Overtemperature shutdown threshold, TJ decreasing | 130 | °C | TJ decreasing | 4 | |||
| EN pulse reset width (MIC2547 thermal shutdown latch) | 5 | µs | MIC2547 thermal shutdown latch | 4 | |||
| VIN to EN set-up | 0 | µs | MIC2547, Note 5 | 4 | |||
| Current-limit response time | 25 | µs | VOUT = oV (as printed) | 4 | |||
| Overcurrent FLG response time | 5 | µs | VOUT = VIN/2 to FLG low | 4 | |||
| Supply voltage (VIN) operating range | VIN | 2.7 | 5.5 | V | Operating Ratings | 4 | |
| Ambient temperature range | TA | -40 | 85 | °C | Operating Ratings | 4 | |
| Current-limit set resistor RSET lower bound | RSET | 154 | Ω | 154Ω < RSET < 2.29kΩ | 3 | ||
| Current-limit set resistor RSET upper bound | RSET | 2.29 | kΩ | 154Ω < RSET < 2.29kΩ | 3 | ||
| Supply voltage (VIN) absolute maximum | VIN | 6 | V | Absolute Maximum Ratings | 4 | ||
| Output voltage (VOUT) absolute maximum | VOUT | 6 | V | Absolute Maximum Ratings | 4 | ||
| Enable input voltage (VEN) minimum | VEN | -0.3 | V | VEN to VIN + 0.3V (upper limit not numeric) | 4 | ||
| Fault flag voltage (VFLG) absolute maximum | VFLG | 6 | V | Absolute Maximum Ratings | 4 | ||
| Storage temperature (TS) | TS | -65 | 150 | °C | Absolute Maximum Ratings | 4 | |
| Lead temperature (soldering) | 260 | °C | soldering 5 sec | 4 | |||
| ESD rating | 2 | kV | Human body model, 1.5k in series with 100pF, Note 3 | 4 | |||
| Package thermal resistance, TSSOP (θJA) | θJA | 100 | °C/W | TSSOP package | 4 | ||
| Current-limit set point accuracy | -20 | 20 | % | Adjustable current-limit, better than ±20% | 12 | ||
| Short-circuit foldback current | 80 | % | Output current folds back to approximately 80% of short-circuit current limit | 12 | |||
| Fault flag output low voltage | 100 | mV | FLGX sinking 10mA load, above ground | 12 |
CAD (KiCad official)
- Symbol:
MIC2547-2YTS - Footprint:
Package_SO:TSSOP-16_4.4x5mm_P0.65mm - 3D model: TSSOP-16 (KiCad packages3D, STEP)
- 3D model files:
mic2547-2yts-etched.step/mic2547-2yts-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mic2547-2yts.step/mic2547-2yts.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (15 pp, sha256
0ba11f6ec8a1c3dc, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).