4a92e91
ME6221CM5G
MICRONE · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · SOT-23-5
ME6221CM5G from MICRONE, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Power input voltage. Operating range 2.8 V to 18 V (absolute max 18 V). Bypass with a 1 uF or larger tantalum capacitor close to the pin. |
| 2 | VSS | power_in | Device ground reference. Connect to system ground return. |
| 3 | CE | input | Chip enable (ON/OFF control). Drive high (>=1.3 V, up to 18 V) to enable the regulator; drive low (<=0.7 V) to disable and enter standby (ICEL ~0 uA). Input leakage is <=0.1 uA. |
| 4 | FB | input | Feedback voltage input. Regulated internally to the 1.25 V reference. Connect to the midpoint of an external resistor divider from VOUT to VSS to set the output voltage: VOUT = 1.25 * (1 + R1/R2). R2 should be >=100 kOhm for best accuracy. |
| 5 | VOUT | power_out | Regulated output voltage, adjustable 1.25 V to 5.0 V, up to 400 mA (typ) / 550 mA (max) with current-limit at ~600 mA. Requires a >=2.2 uF tantalum output capacitor with ESR <1 Ohm for stability. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MICRONE |
| Package | SOT-23-5 |
| Category | PMIC |
| Pins | 5 |
Ordering variants
Same part, different packaging or reel option.
ME6221CM5G
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage (effective, VOUT(E)) / Output Voltage (trimmed, VOUT(T)) | VOUT(E)/VOUT(T) | 0.98 | 1.02 | V | IOUT=30mA; printed as 'X 0.98' / 'X 1.02' (X = nominal VOUT) | 5 | |
| Output Voltage Range | VROUT | 1.25 | 5 | V | VIN=VOUT(T)+1V, VCE=VIN, using test circuit 2 | 5 | |
| Maximum Output Current | IOUTMAX | 400 | 550 | mA | VIN=VOUT+1V (Note 1) | 5 | |
| Load Regulation | ΔVOUT | 4 | 10 | mV | 1mA≤IOUT≤100mA | 5 | |
| Dropout Voltage VDIF1 | VDIF1 | 125 | 140 | mV | IOUT=100mA | 5 | |
| Dropout Voltage VDIF2 | VDIF2 | 250 | 270 | mV | IOUT=200mA | 5 | |
| Supply Current | ISS | 45 | 60 | μA | VIN=3V, VCE=VIN | 5 | |
| Stand-by Current | ICEL | 0 | 1 | μA | VIN=3V, VCE=0V | 5 | |
| Line Regulation | ΔVOUT | 4 | 15 | mV | IOUT=30mA, Vout+1V ≤ VIN ≤ 18V (Note 1) | 5 | |
| CE High Voltage | VCEH | 1.3 | 18 | V | RL=1.0KΩ | 5 | |
| CE Low Voltage | VCEL | 0 | 0.7 | V | RL=1.0KΩ | 5 | |
| CE High Current | ISH | -0.1 | 0.1 | μA | VCE=7V | 5 | |
| CE Low Current | ISL | -0.1 | 0.1 | μA | VCE=0V | 5 | |
| Short-circuit Current | ISHORT | 70 | mA | VOUT=0V | 5 | ||
| Thermal Shutdown Protection | Tsd | 165 | ℃ | IOUT=1mA | 5 | ||
| Over Current Protection | Ilimit | 600 | mA | 5 | |||
| Operating Voltage Range (input) | VIN | 2.8 | 18 | V | 1 | ||
| Input Voltage | VIN | 18 | V | 4 | |||
| Output Current | IOUT | 500 | mA | 4 | |||
| Output Voltage | VOUT | -0.3 | 8 | V | Referenced to VSS (printed Vss-0.3~8.0) | 4 | |
| Power Dissipation SOT23-5 | PD | 300 | mW | 4 | |||
| Operating Temperature Range | TOPR | -40 | 150 | ℃ | 4 | ||
| Storage Temperature Range | TSTG | -55 | 150 | ℃ | 4 | ||
| Lead Temperature | 260 | ℃ | 4 sec | 4 |
CAD (KiCad official)
- Symbol:
ME6221CM5G - Footprint:
Package_TO_SOT_SMD:SOT-23-5 - 3D model: SOT-23-5 (KiCad packages3D, STEP)
- 3D model files:
me6221cm5g-etched.step/me6221cm5g-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);me6221cm5g.step/me6221cm5g.glbare the bare package body.
3D model downloads
Two STEP files. Same geometry, different body top:
| File | Size | Use it when |
|---|---|---|
me6221cm5g.step |
85 KB | You want the bare part, or you mark your own boards. |
me6221cm5g-etched.step |
1.9 MB | You want the part with ME6221CM5G already on it. |
The marking in the etched file is real recessed geometry cut into the solid, not a texture or a decal: 460 faces against 102 in the bare model. It survives export, section views, and rendering in any CAD tool, and it drops straight into KiCad or Fusion with no extra setup.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MICRONE datasheet (10 pp, sha256
2b7a8783ac554210, retrieved 2026-08-17, tier: lcsc) - Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# ME6221CM5G
**MICRONE** · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · SOT-23-5
ME6221CM5G from MICRONE, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Power input voltage. Operating range 2.8 V to 18 V (absolute max 18 V). Bypass with a 1 uF or larger tantalum capacitor close to the pin. |
| 2 | VSS | power_in | Device ground reference. Connect to system ground return. |
| 3 | CE | input | Chip enable (ON/OFF control). Drive high (>=1.3 V, up to 18 V) to enable the regulator; drive low (<=0.7 V) to disable and enter standby (ICEL ~0 uA). Input leakage is <=0.1 uA. |
| 4 | FB | input | Feedback voltage input. Regulated internally to the 1.25 V reference. Connect to the midpoint of an external resistor divider from VOUT to VSS to set the output voltage: VOUT = 1.25 * (1 + R1/R2). R2 should be >=100 kOhm for best accuracy. |
| 5 | VOUT | power_out | Regulated output voltage, adjustable 1.25 V to 5.0 V, up to 400 mA (typ) / 550 mA (max) with current-limit at ~600 mA. Requires a >=2.2 uF tantalum output capacitor with ESR <1 Ohm for stability. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MICRONE |
| Package | SOT-23-5 |
| Category | PMIC |
| Pins | 5 |
## Ordering variants
Same part, different packaging or reel option.
- `ME6221CM5G`
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage (effective, VOUT(E)) / Output Voltage (trimmed, VOUT(T)) | VOUT(E)/VOUT(T) | 0.98 | | 1.02 | V | IOUT=30mA; printed as 'X 0.98' / 'X 1.02' (X = nominal VOUT) | 5 |
| Output Voltage Range | VROUT | 1.25 | | 5 | V | VIN=VOUT(T)+1V, VCE=VIN, using test circuit 2 | 5 |
| Maximum Output Current | IOUTMAX | | 400 | 550 | mA | VIN=VOUT+1V (Note 1) | 5 |
| Load Regulation | ΔVOUT | | 4 | 10 | mV | 1mA≤IOUT≤100mA | 5 |
| Dropout Voltage VDIF1 | VDIF1 | | 125 | 140 | mV | IOUT=100mA | 5 |
| Dropout Voltage VDIF2 | VDIF2 | | 250 | 270 | mV | IOUT=200mA | 5 |
| Supply Current | ISS | | 45 | 60 | μA | VIN=3V, VCE=VIN | 5 |
| Stand-by Current | ICEL | 0 | | 1 | μA | VIN=3V, VCE=0V | 5 |
| Line Regulation | ΔVOUT | | 4 | 15 | mV | IOUT=30mA, Vout+1V ≤ VIN ≤ 18V (Note 1) | 5 |
| CE High Voltage | VCEH | 1.3 | | 18 | V | RL=1.0KΩ | 5 |
| CE Low Voltage | VCEL | 0 | | 0.7 | V | RL=1.0KΩ | 5 |
| CE High Current | ISH | -0.1 | | 0.1 | μA | VCE=7V | 5 |
| CE Low Current | ISL | -0.1 | | 0.1 | μA | VCE=0V | 5 |
| Short-circuit Current | ISHORT | | 70 | | mA | VOUT=0V | 5 |
| Thermal Shutdown Protection | Tsd | | 165 | | ℃ | IOUT=1mA | 5 |
| Over Current Protection | Ilimit | | 600 | | mA | | 5 |
| Operating Voltage Range (input) | VIN | 2.8 | | 18 | V | | 1 |
| Input Voltage | VIN | | | 18 | V | | 4 |
| Output Current | IOUT | | | 500 | mA | | 4 |
| Output Voltage | VOUT | -0.3 | | 8 | V | Referenced to VSS (printed Vss-0.3~8.0) | 4 |
| Power Dissipation SOT23-5 | PD | | | 300 | mW | | 4 |
| Operating Temperature Range | TOPR | -40 | | 150 | ℃ | | 4 |
| Storage Temperature Range | TSTG | -55 | | 150 | ℃ | | 4 |
| Lead Temperature | | | | 260 | ℃ | 4 sec | 4 |
## CAD (KiCad official)
- Symbol: `ME6221CM5G`
- Footprint: `Package_TO_SOT_SMD:SOT-23-5`
- 3D model: SOT-23-5 (KiCad packages3D, STEP)
- 3D model files: `me6221cm5g-etched.step` / `me6221cm5g-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `me6221cm5g.step` / `me6221cm5g.glb` are the bare package body.
## 3D model downloads
Two STEP files. Same geometry, different body top:
| File | Size | Use it when |
|---|---|---|
| [`me6221cm5g.step`](me6221cm5g.step) | 85 KB | You want the bare part, or you mark your own boards. |
| [`me6221cm5g-etched.step`](me6221cm5g-etched.step) | 1.9 MB | You want the part with `ME6221CM5G` already on it. |
The marking in the etched file is real recessed geometry cut into the solid, not a
texture or a decal: 460 faces against 102 in the bare model. It
survives export, section views, and rendering in any CAD tool, and it drops straight
into KiCad or Fusion with no extra setup.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [MICRONE datasheet](docs/me6221cm5g-datasheet.pdf) (10 pp, sha256 `2b7a8783ac554210`, retrieved 2026-08-17, tier: lcsc)
- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/me6221cm5g-datasheet.pdf)