← Commit history

me3118aspg: restore the component block (pinout + model declarations) from this page's own README and symbol

Ray ·9fbba88385 · ·parent fe7c4e8
1 file changed +80−1
page.json+80−1
@@ -31,5 +31,84 @@   "author": {     "name": "Ray",     "email": "[email protected]"+  },+  "component": {+    "mpn": "ME3118ASPG",+    "manufacturer": "MICRONE",+    "package": "ESOP-8",+    "pin_count": 9,+    "category": "DC-DC Converters",+    "parts": {+      "symbol": "me3118aspg.kicad_sym",+      "footprint": "me3118aspg.kicad_mod",+      "model_3d": "me3118aspg-etched.glb",+      "model_3d_plain": "me3118aspg.glb",+      "model_3d_step": "me3118aspg-etched.step",+      "model_3d_step_plain": "me3118aspg.step",+      "lbr": "me3118aspg.lbr"+    },+    "pins": [+      {+        "number": "1",+        "name": "PGND",+        "type": "power_in",+        "description": "Power ground. Return path for the internal low-side NMOS power switch. Must be connected to AGND (recommended star-tie at a single point to avoid PGND noise coupling into AGND)."+      },+      {+        "number": "2",+        "name": "VIN",+        "type": "power_in",+        "description": "Power supply input, 4.5 V to 18 V (absolute max 20 V). The device starts operating when VIN is above the UVLO threshold (typ. 4.0 V rising / 3.6 V falling) and EN is high. Bypass with a low-ESR ceramic input capacitor placed close to this pin and PGND."+      },+      {+        "number": "3",+        "name": "AGND",+        "type": "power_in",+        "description": "Analog ground and reference potential for the internal controller. Must be connected to PGND (single-point tie when a ground plane is not used)."+      },+      {+        "number": "4",+        "name": "FB",+        "type": "input",+        "description": "Feedback input to the internal error amplifier. Set the output voltage with a resistor divider from VOUT to AGND: VO = 0.8 V × (1 + R1/R2). Internal reference VFB = 0.8 V (788-812 mV); input bias current is 200 nA max."+      },+      {+        "number": "5",+        "name": "COMP",+        "type": "output",+        "description": "External loop compensation node - output of the internal transconductance error amplifier. Connect a series RC network from COMP to AGND to place the compensation pole/zero pair. Internal clamp limits COMP swing to approximately 0.4 V to 2.5 V."+      },+      {+        "number": "6",+        "name": "EN",+        "type": "input",+        "description": "Enable input. Drive high (≥2 V) to enable the regulator; drive low (≤0.6 V) to shut it down (IOFF ≈ 1 µA typ.). Input hysteresis ~200 mV; input current ≤1 µA. Do not float - tie to VIN if enable control is not needed."+      },+      {+        "number": "7",+        "name": "SS",+        "type": "output",+        "description": "Soft-start pin. An internal 5 µA current source charges an external capacitor from SS to AGND, ramping the internal reference during startup to limit inrush current and provide a monotonic output rise. Typical soft-start time is ~3 ms."+      },+      {+        "number": "8",+        "name": "NC",+        "type": "unconnected",+        "description": "No internal connection. Leave floating or tie to ground for best PCB layout; do not use as a routing via."+      },+      {+        "number": "9",+        "name": "LX",+        "type": "power_out",+        "description": "Switch node - exposed thermal pad on the ESOP-8. Internally the common drain of the high-side PMOS and low-side NMOS power switches; connect to the external filter inductor. Also serves as the primary thermal dissipation path - solder to a large copper area to lower θJA. Absolute max: −0.7 V to VIN+0.3 V DC (−5 V to 22 V for 20 ns transients)."+      }+    ],+    "provenance": {+      "rebuilt": "component block rebuilt 2026-10-05 from this page's own README pinout table and .kicad_sym (pins cross-checked), no re-extraction"+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }   }-}\ No newline at end of file+}