3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownME2206AM6G-N
MICRONE · DC-DC Controllers · SOT-23-6
ME2206AM6G-N from MICRONE, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | SW is the switch node of the boost converter, rated for -0.3V to 6V. |
| 2 | GND | power_in | GND is the ground pin, and the LED current sense resistor Rs is connected between GND and FB. |
| 3 | FB | input | FB is the feedback pin with a internally regulated 95mV reference, where LED current is set as 95mV/Rs. |
| 4 | SHDN | input | SHDN is the shutdown control pin, with input high VSH of 1.0V minimum and input low VSL of 0.4V maximum at Vin=1.8V. |
| 5 | VOUT | power_out | VOUT is the boost output, which also supplies the IC; the load-open protection lets VOUT rise to 5V before the part stops switching. |
| 6 | VIN | power_in | VIN is the input supply, with an input voltage range of 0.9V minimum to VF-0.2V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | MICRONE |
| Package | SOT-23-6 |
| Category | Power Supply Chip |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage Range | Vin | 0.9 | V | 4 | |||
| Feedback Voltage | VFB | 85 | 95 | 105 | mV | 4 | |
| Start-up Voltage | VSTART | 0.9 | V | Vin:0V~3V, ILED =270mA | 4 | ||
| Hold Voltage | VHOLD | 0.75 | V | Vin:3V~0V, ILED =750mA~200mA | 4 | ||
| SHDN Input High | VSH | 1 | V | Vin=1.8V | 4 | ||
| SHDN Input Low | VSL | 0.4 | V | Vin=1.8V | 4 | ||
| Maximum Output Current Range | IMAX | 750 | mA | 4 | |||
| Quiescent Current | IQ | 1 | 3 | mA | ILED =0mA,Vout=3.4V,Device Switch at 1MHz | 4 | |
| Shutdown Current | ISD | 1 | uA | Shutdown mode | 4 | ||
| Input Voltage | VIN | -0.3 | 6 | V | 4 | ||
| SW Pin Voltage | SW | -0.3 | 6 | V | 4 | ||
| SHDN, FB Pin Voltage | SHDN/FB | -0.3 | 6 | V | 4 | ||
| Operating Temperature Range | TOPR | -40 | 85 | ℃ | 4 | ||
| Storage Temperature Range | TSTG | -55 | 125 | ℃ | 4 | ||
| Lead Temperature (Soldering) | TL | 260 | ℃ | Soldering, 10 sec | 4 | ||
| Internal Power Dissipation | PD | 400 | mW | SOT23-6 package | 4 | ||
| Switch on Resistance | RDSON | 0.1 | Ω | Vout=3.4V | 4 | ||
| Current Limit | ILIM | 2 | A | Vout=3.4V | 4 | ||
| Efficiency | η | 90 | % | ILED =750mA | 4 | ||
| Oscillator Frequency | FOSC | 1 | MHz | 4 | |||
| Over Temperature Shutdown | OTS | 150 | ℃ | 4 | |||
| Over Temperature Hysteresis | OTH | 15 | ℃ | 4 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| housing | ppa | body, such as exercise equipment, medical equipment, security systems, gas equipment, or any apparatus installed in airplanes and other vehicles, without prior written permission of Nanjing Micro | 9 |
CAD (KiCad official)
- Symbol:
ME2206AM6G-N - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.25 mm tall, datasheet A, midpoint of min and max). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
me2206am6g-n-etched.step/me2206am6g-n-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);me2206am6g-n.step/me2206am6g-n.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: MICRONE datasheet (9 pp, sha256
c6d024b04ca5a2ff, retrieved 2026-11-12, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).