main
History Download
Ray Publish 0.1.0 4755002

MCP9902T-1E

Microchip Tech · Temperature Sensors · WDFN-8-EP(2x2)

MCP9902T-1E from Microchip Tech, in a WDFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VDD power_in Power supply pin for the device, operating range 3.0 V to 3.6 V.
2 DP1 passive Analog connection to the anode of remote diode 1.
3 DN1 passive Analog connection to the cathode of remote diode 1.
4 THERM/ADDR output Open-drain, non-maskable THERM limit alert that asserts low when the hardware-set THERM limit is exceeded by a temperature sensor; if enabled, the pull-up resistor on this pin sets the SMBus slave address.
5 GND power_in System ground for the device.
6 ALERT/THERM2 output Open-drain maskable ALERT output that asserts when a diode temperature exceeds the ALERT threshold and may be masked by register settings.
7 SMDATA bidirectional Open-drain, bidirectional SMBus data pin.
8 SMCLK input SMBus input clock pin for SMBus communication, up to 400 kHz clock rate.
9 EP passive Exposed thermal pad, not internally connected, but grounding is recommended for mechanical support.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package WDFN-8-EP(2x2)
Category Sensors
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VDD 3 3.3 3.6 V 3
Supply Current IDD 200 450 µA 0.0625 conversion/second, dynamic averaging disabled 3
Supply Current IDD 225 600 µA 1 conversion/second, dynamic averaging enabled 3
Supply Current IDD 450 850 µA 4 conversions/second, dynamic averaging enabled 3
Supply Current IDD 1120 1500 µA > 16 conversions/second, dynamic averaging enabled 3
One-Shot Supply Current IDD_OS 170 230 µA Device in One-Shot state, no active SMBus communications, ALERT and THERM pins not asserted. 3
Standby Supply Current IDD_SBY 170 230 µA Device in Standby state, no SMBus communications, ALERT and THERM pins not asserted. 3
Power-on Reset Voltage POR_V 0.6 0.9 V Pin states defined 3
VDD Rise Rate VDD_RISE 0.05 V/ms 0 to 3V in 60 ms 3
External Temperature Accuracy (MCP9902) -1 0.25 1 °C -40°C < TDIODE < +105°C, -40°C < TA < +65°C 4
External Temperature Accuracy (MCP9902) -2 0.25 2 °C -40°C < TDIODE < +125°C, -40°C < TA < +125°C 4
Internal Temperature Accuracy -1 0.25 1 °C -40°C < TA < +65°C 4
Internal Temperature Accuracy -2 0.5 2 °C -40°C < TA < +125°C 4
Time to First Communications tINT_T 15 20 ms Time after power up before ready to begin communications and measurement 4
Capacitive Filter CFILTER 2.2 2.7 nF Connected across external diode 4
ALERT/THERM Output Low Voltage VOL 0.4 V ISINK = 8 mA 4
ALERT/THERM Leakage Current ILEAK 5 µA ALERT and THERM pins, Device powered or unpowered, TA < +85°C, pull-up voltage < 3.6V 4
SMBus Input High Voltage VIH 2.1 V max VDD 6
SMBus Input Low Voltage VIL -0.3 0.8 V 6
SMBus Leakage Current ILEAK 5 µA Powered or unpowered, TA < +85°C 6
Output Low Sink Current IOL 8.2 15 mA SMDATA = 0.2V 6
Clock Frequency fSMB 10 400 kHz 6
Bus Free Time Stop to Start tBUF 1.3 µs 6
Clock Low Period tLOW 1.3 µs 6
Clock High Period tHIGH 0.6 µs 6
Timeout tTIMEOUT 25 35 ms Per bus line 6
Ambient Temperature under Bias -40 125 °C 3
Storage Temperature -65 150 °C 3
Voltage on VDD with respect to VSS -0.3 4 V 3
Voltage on all other pins with respect to VSS -0.3 V max (VDD + 0.3V) 3
Total Power Dissipation 500 mW Rating up to +85°C 3
Maximum Current out of VSS pin 20 mA 3
Maximum Current into VDD pin 20 mA 3
Clamp Current IK 20 mA VPIN < 0 or VPIN > VDD 3
ESD Rating, All pins HBM 2000 V 3
Input Current, any pin except VDD 10 mA 3
Specified Temperature Range TA -40 125 °C 4
Operating Temperature Range TA -40 125 °C 4
Storage Temperature Range TA -65 125 °C 4
Thermal Resistance, 8L-WDFN, 2x2 θJA 141.3 °C/W JEDEC 2s2p, board size 76.2 x 114.3 x 1.6 mm, 1 via, airflow = 0 m/s 4
Power-On Reset Release Voltage PORR 1.45 V Rising VDD 3

CAD (KiCad official)

  • Symbol: MCP9902T-1E
  • Footprint: Package_DFN_QFN:WDFN-8-1EP_2x2mm_P0.5mm_EP0.8x1.2mm
  • 3D model: WDFN-8-EP(2x2), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm nominal WSON height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
  • 3D model files: mcp9902t-1e-etched.step / mcp9902t-1e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp9902t-1e.step / mcp9902t-1e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (50 pp, sha256 458bdf381d32ab84, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF