main
History Download
Ray Publish 0.1.0 b6255b5

MCP79521-I

Microchip Tech · Real-time Clocks (RTC) · MSOP-10

MCP79521-I from Microchip Tech, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 X1 input Quartz crystal input for the 32.768 kHz crystal (optimized for 6-9 pF load) and also the external clock input when EXTOSC is set.
2 X2 output Quartz crystal output for the 32.768 kHz crystal; leave floating when an external clock is used on X1.
3 VBAT power_in Backup supply input (1.3V to 3.6V) that maintains the RTCC and SRAM when VCC is unavailable; connect to VSS if battery backup is not used.
4 CS input Active-low chip select; a high level deselects the device and puts SO in high-impedance, and a high-to-low transition is required after power-up before any sequence.
5 VSS power_in Ground.
6 SI input Serial data input for instructions, addresses and data, latched on the rising edge of SCK.
7 SO tri_state Serial data output, shifted out after the falling edge of SCK and high-impedance when CS is high.
8 SCK input Serial clock input that synchronizes communication, up to 5 MHz.
9 MFP bidirectional Multifunction pin shared by the clock output and alarms; requires an external pull-up to VCC or VBAT and has a maximum sink current of 10 mA.
10 VCC power_in Primary power supply, operating range 1.8V to 3.6V.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package MSOP-10
Category RTC/Clock Chip
Pins 10

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage (VCC) VCC 1.8 3.6 V Industrial TA = -40°C to +85°C 4
Power-Fail Switchover Voltage VTRIP 1.3 1.5 1.7 V 5
Backup Supply Voltage Range VBAT 1.3 3.6 V 5
Low-Level Input Voltage (min) VIL -0.3 V Max is 0.3VCC (VCC ≥ 2.5V) or 0.2VCC (VCC < 2.5V) 4
Low-Level Output Voltage VOL 0.4 V IOL = 2.1 mA, VCC ≥ 2.5V 4
Low-Level Output Voltage VOL 0.2 V IOL = 1.0 mA, VCC < 2.5V 4
Input Leakage Current ILI -1 1 µA CS = VCC, VIN = VSS or VCC 4
Output Leakage Current ILO -1 1 µA CS = VCC, VOUT = VSS or VCC 4
Pin Capacitance (all inputs and outputs) CINT 7 pF VCC = 3.6V, TA = +25°C, f = 1 MHz (Note 2) 4
EEPROM Read Operating Current ICCEERD 3 mA VCC = 3.6V, FCLK = 5 MHz, SO = Open 4
EEPROM Write Operating Current ICCEEWR 5 mA VCC = 3.6V 4
SRAM/RTCC Read Operating Current ICCREAD 3 mA VCC = 3.6V, FCLK = 5 MHz, SO = Open 4
SRAM/RTCC Write Operating Current ICCWRITE 3 mA VCC = 3.6V, FCLK = 5 MHz 4
VCC Data Retention Current (oscillator off) ICCDAT 1 µA VCC = 3.6V 4
Timekeeping Current ICCT 1.2 µA VCC = 1.8V, CS = VCC (Note 2) 4
Timekeeping Current ICCT 1.2 1.8 µA VCC = 3.0V, CS = VCC (Note 2) 4
Timekeeping Current ICCT 2.6 µA VCC = 3.6V, CS = VCC (Note 2) 4
Timekeeping Backup Current IBATT 850 nA VBAT = 1.3V, VCC = VSS (Note 2) 5
Timekeeping Backup Current IBATT 1000 1200 nA VBAT = 3.0V, VCC = VSS (Note 2) 5
Timekeeping Backup Current IBATT 2300 nA VBAT = 3.6V, VCC = VSS (Note 2) 5
VBAT Data Retention Current (oscillator off) IBATDAT 850 nA VBAT = 3.6V, VCC = VSS 5
Clock Frequency FCLK 5 MHz 2.5V ≤ Vcc < 3.6V 6
Clock Frequency FCLK 3 MHz 1.8V ≤ Vcc < 2.5V 6
CS Setup Time TCSS 100 ns 2.5V ≤ Vcc < 3.6V 6
CS Setup Time TCSS 150 ns 1.8V ≤ Vcc < 2.5V 6
CS Hold Time TCSH 100 ns 2.5V ≤ Vcc < 3.6V 6
CS Hold Time TCSH 150 ns 1.8V ≤ Vcc < 2.5V 6
CS Disable Time TCSD 50 ns 6
Data Setup Time TSU 20 ns 2.5V ≤ Vcc < 3.6V 6
Data Setup Time TSU 30 ns 1.8V ≤ Vcc < 2.5V 6
Data Hold Time THD 40 ns 2.5V ≤ Vcc < 3.6V 6
Data Hold Time THD 50 ns 1.8V ≤ Vcc < 2.5V 6
SCK Rise Time TR 100 ns Note 1 6
SCK Fall Time TF 100 ns Note 1 6
Clock High Time THI 100 ns 2.5V ≤ Vcc < 3.6V 6
Clock High Time THI 150 ns 1.8V ≤ Vcc < 2.5V 6
Clock Low Time TLO 100 ns 2.5V ≤ Vcc < 3.6V 6
Clock Low Time TLO 150 ns 1.8V ≤ Vcc < 2.5V 6
Clock Delay Time TCLD 50 ns 6
Clock Enable Time TCLE 50 ns 6
Output Valid from Clock Low TV 100 ns 2.5V ≤ Vcc < 3.6V 6
Output Valid from Clock Low TV 160 ns 1.8V ≤ Vcc < 2.5V 6
Output Hold Time THO 0 ns Note 1 6
Output Disable Time TDIS 80 ns 2.5V ≤ Vcc < 3.6V (Note 1) 6
Output Disable Time TDIS 160 ns 1.8V ≤ Vcc < 2.5V (Note 1) 6
Internal Write Cycle Time TWC 5 ms Note 2 6
VCC Fall Time TFVCC 300 µs Note 1 6
VCC Rise Time TRVCC 0 µs Note 1 6
Absolute max input/output voltage w.r.t. VSS (lower limit) -0.6 V All inputs and outputs w.r.t. VSS; upper limit VCC+1.0V 4
Storage temperature -65 150 °C 4
Ambient temperature under bias -40 85 °C 4
ESD protection on all pins 4 kV 4
Operating temperature (Industrial) TA -40 85 °C Industrial (I) 4
Oscillator Pin Capacitance (X1, X2) COSC 3 pF Note 2 4
Oscillator Frequency FOSC 32.768 kHz 6
Oscillator Timeout Period TOSF 1 ms Note 1 6

CAD (KiCad official)

  • Symbol: MCP79521-I
  • Footprint: Package_SO:MSOP-10_3x3mm_P0.5mm
  • 3D model: MSOP-10 (KiCad packages3D, STEP)
  • 3D model files: mcp79521-i-etched.step / mcp79521-i-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp79521-i.step / mcp79521-i.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (58 pp, sha256 1caaeadd97693b59, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF