main
Ray
Publish 0.1.0
1d36174
MCP79510-I
Microchip Tech · Real-time Clocks (RTC) · MSOP-10
MCP79510-I from Microchip Tech, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | X1 | input | Quartz crystal input for the 32.768 kHz crystal (optimized for 6-9 pF load capacitance), also serves as the external clock input when configured for an external oscillator. |
| 2 | X2 | output | Quartz crystal output for the 32.768 kHz crystal; leave floating when an external clock is used on X1. |
| 3 | VBAT | power_in | Backup supply input (1.3V to 3.6V) that maintains the RTCC and SRAM registers when VCC is unavailable; connect to VSS if battery backup is not used. |
| 4 | CS | input | Active-low chip select input; a high level deselects the device and puts SO in high impedance, and a high-to-low transition is required after power-up before any sequence. |
| 5 | VSS | power_in | Ground. |
| 6 | SI | input | Serial data input that receives instructions, addresses and data, latched on the rising edge of SCK. |
| 7 | SO | tri_state | Serial data output shifted out after the falling edge of SCK, going high-impedance when CS is deselected. |
| 8 | SCK | input | Serial clock input that synchronizes SPI communication, up to 5 MHz; SI is latched on the rising edge and SO updates after the falling edge. |
| 9 | MFP | bidirectional | Multifunction pin shared with the clock output divider and alarms; requires an external pull-up to VCC or VBAT, with a maximum sink current of 10 mA. |
| 10 | VCC | power_in | Primary power supply with operating voltage range of 1.8V to 3.6V; power should be applied to VCC before VBAT. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-10 |
| Category | Clock and Timing |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VCC | VCC | 1.8 | 3.6 | V | Industrial (I) | 4 | |
| Operating temperature | TA | -40 | 85 | °C | Industrial (I) | 4 | |
| Backup supply voltage range | VBAT | 1.3 | 3.6 | V | 5 | ||
| Power-fail switchover voltage | VTRIP | 1.3 | 1.5 | 1.7 | V | 5 | |
| Storage temperature | -65 | 150 | °C | 4 | |||
| Ambient temperature under bias | -40 | 85 | °C | 4 | |||
| ESD protection on all pins | 4 | kV | 4 | ||||
| Low-level output voltage | VOL | 0.4 | V | IOL = 2.1 mA, VCC ≥ 2.5V | 4 | ||
| Low-level output voltage | VOL | 0.2 | V | IOL = 1.0 mA, VCC < 2.5V | 4 | ||
| Input leakage current | ILI | -1 | 1 | µA | CS = VCC, VIN = VSS or VCC | 4 | |
| Output leakage current | ILO | -1 | 1 | µA | CS = VCC, VOUT = VSS or VCC | 4 | |
| Pin capacitance (all inputs and outputs) | CINT | 7 | pF | VCC = 3.6V, TA = +25°C, f = 1 MHz | 4 | ||
| EEPROM read operating current | ICCEERD | 3 | mA | VCC = 3.6V, FCLK = 5 MHz, SO = Open | 4 | ||
| EEPROM write operating current | ICCEEWR | 5 | mA | VCC = 3.6V | 4 | ||
| SRAM/RTCC read operating current | ICCREAD | 3 | mA | VCC = 3.6V, FCLK = 5 MHz, SO = Open | 4 | ||
| SRAM/RTCC write operating current | ICCWRITE | 3 | mA | VCC = 3.6V, FCLK = 5 MHz | 4 | ||
| VCC data retention current (oscillator off) | ICCDAT | 1 | µA | VCC = 3.6V | 4 | ||
| Timekeeping current | ICCT | 1.2 | µA | VCC = 1.8V, CS = VCC | 4 | ||
| Timekeeping current | ICCT | 1.2 | 1.8 | µA | VCC = 3.0V, CS = VCC | 4 | |
| Timekeeping current | ICCT | 2.6 | µA | VCC = 3.6V, CS = VCC | 4 | ||
| Timekeeping backup current | IBATT | 850 | nA | VBAT = 1.3V, VCC = VSS | 5 | ||
| Timekeeping backup current | IBATT | 1000 | 1200 | nA | VBAT = 3.0V, VCC = VSS | 5 | |
| Timekeeping backup current | IBATT | 2300 | nA | VBAT = 3.6V, VCC = VSS | 5 | ||
| VBAT data retention current (oscillator off) | IBATDAT | 850 | nA | VBAT = 3.6V, VCC = VSS | 5 | ||
| Oscillator pin capacitance (X1, X2) | COSC | 3 | pF | 4 | |||
| Oscillator frequency | FOSC | 32.768 | kHz | 6 | |||
| Clock frequency | FCLK | 5 | MHz | 2.5V ≤ Vcc < 3.6V | 6 | ||
| Clock frequency | FCLK | 3 | MHz | 1.8V ≤ Vcc < 2.5V | 6 | ||
| CS setup time | TCSS | 100 | ns | 2.5V ≤ Vcc < 3.6V | 6 | ||
| CS setup time | TCSS | 150 | ns | 1.8V ≤ Vcc < 2.5V | 6 | ||
| CS hold time | TCSH | 100 | ns | 2.5V ≤ Vcc < 3.6V | 6 | ||
| CS hold time | TCSH | 150 | ns | 1.8V ≤ Vcc < 2.5V | 6 | ||
| CS disable time | TCSD | 50 | ns | 6 | |||
| Data setup time | TSU | 20 | ns | 2.5V ≤ Vcc < 3.6V | 6 | ||
| Data setup time | TSU | 30 | ns | 1.8V ≤ Vcc < 2.5V | 6 | ||
| Data hold time | THD | 40 | ns | 2.5V ≤ Vcc < 3.6V | 6 | ||
| Data hold time | THD | 50 | ns | 1.8V ≤ Vcc < 2.5V | 6 | ||
| SCK rise time | TR | 100 | ns | 6 | |||
| SCK fall time | TF | 100 | ns | 6 | |||
| Clock high time | THI | 100 | ns | 2.5V ≤ Vcc < 3.6V | 6 | ||
| Clock high time | THI | 150 | ns | 1.8V ≤ Vcc < 2.5V | 6 | ||
| Clock low time | TLO | 100 | ns | 2.5V ≤ Vcc < 3.6V | 6 | ||
| Clock low time | TLO | 150 | ns | 1.8V ≤ Vcc < 2.5V | 6 | ||
| Clock delay time | TCLD | 50 | ns | 6 | |||
| Clock enable time | TCLE | 50 | ns | 6 | |||
| Output valid from clock low | TV | 100 | ns | 2.5V ≤ Vcc < 3.6V | 6 | ||
| Output valid from clock low | TV | 160 | ns | 1.8V ≤ Vcc < 2.5V | 6 | ||
| Output hold time | THO | 0 | ns | 6 | |||
| Output disable time | TDIS | 80 | ns | 2.5V ≤ Vcc < 3.6V | 6 | ||
| Output disable time | TDIS | 160 | ns | 1.8V ≤ Vcc < 2.5V | 6 | ||
| Internal write cycle time | TWC | 5 | ms | 6 | |||
| VCC fall time | TFVCC | 300 | µs | 6 | |||
| VCC rise time | TRVCC | 0 | µs | 6 | |||
| Oscillator timeout period | TOSF | 1 | ms | 6 |
CAD (KiCad official)
- Symbol:
MCP79510-I - Footprint:
Package_SO:MSOP-10_3x3mm_P0.5mm - 3D model: MSOP-10 (KiCad packages3D, STEP)
- 3D model files:
mcp79510-i-etched.step/mcp79510-i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp79510-i.step/mcp79510-i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (58 pp, sha256
1caaeadd97693b59, retrieved 2026-10-23, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MCP79510-I
**Microchip Tech** · Real-time Clocks (RTC) · MSOP-10
MCP79510-I from Microchip Tech, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | X1 | input | Quartz crystal input for the 32.768 kHz crystal (optimized for 6-9 pF load capacitance), also serves as the external clock input when configured for an external oscillator. |
| 2 | X2 | output | Quartz crystal output for the 32.768 kHz crystal; leave floating when an external clock is used on X1. |
| 3 | VBAT | power_in | Backup supply input (1.3V to 3.6V) that maintains the RTCC and SRAM registers when VCC is unavailable; connect to VSS if battery backup is not used. |
| 4 | CS | input | Active-low chip select input; a high level deselects the device and puts SO in high impedance, and a high-to-low transition is required after power-up before any sequence. |
| 5 | VSS | power_in | Ground. |
| 6 | SI | input | Serial data input that receives instructions, addresses and data, latched on the rising edge of SCK. |
| 7 | SO | tri_state | Serial data output shifted out after the falling edge of SCK, going high-impedance when CS is deselected. |
| 8 | SCK | input | Serial clock input that synchronizes SPI communication, up to 5 MHz; SI is latched on the rising edge and SO updates after the falling edge. |
| 9 | MFP | bidirectional | Multifunction pin shared with the clock output divider and alarms; requires an external pull-up to VCC or VBAT, with a maximum sink current of 10 mA. |
| 10 | VCC | power_in | Primary power supply with operating voltage range of 1.8V to 3.6V; power should be applied to VCC before VBAT. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-10 |
| Category | Clock and Timing |
| Pins | 10 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage VCC | VCC | 1.8 | | 3.6 | V | Industrial (I) | 4 |
| Operating temperature | TA | -40 | | 85 | °C | Industrial (I) | 4 |
| Backup supply voltage range | VBAT | 1.3 | | 3.6 | V | | 5 |
| Power-fail switchover voltage | VTRIP | 1.3 | 1.5 | 1.7 | V | | 5 |
| Storage temperature | | -65 | | 150 | °C | | 4 |
| Ambient temperature under bias | | -40 | | 85 | °C | | 4 |
| ESD protection on all pins | | | | 4 | kV | | 4 |
| Low-level output voltage | VOL | | | 0.4 | V | IOL = 2.1 mA, VCC ≥ 2.5V | 4 |
| Low-level output voltage | VOL | | | 0.2 | V | IOL = 1.0 mA, VCC < 2.5V | 4 |
| Input leakage current | ILI | -1 | | 1 | µA | CS = VCC, VIN = VSS or VCC | 4 |
| Output leakage current | ILO | -1 | | 1 | µA | CS = VCC, VOUT = VSS or VCC | 4 |
| Pin capacitance (all inputs and outputs) | CINT | | | 7 | pF | VCC = 3.6V, TA = +25°C, f = 1 MHz | 4 |
| EEPROM read operating current | ICCEERD | | | 3 | mA | VCC = 3.6V, FCLK = 5 MHz, SO = Open | 4 |
| EEPROM write operating current | ICCEEWR | | | 5 | mA | VCC = 3.6V | 4 |
| SRAM/RTCC read operating current | ICCREAD | | | 3 | mA | VCC = 3.6V, FCLK = 5 MHz, SO = Open | 4 |
| SRAM/RTCC write operating current | ICCWRITE | | | 3 | mA | VCC = 3.6V, FCLK = 5 MHz | 4 |
| VCC data retention current (oscillator off) | ICCDAT | | | 1 | µA | VCC = 3.6V | 4 |
| Timekeeping current | ICCT | | | 1.2 | µA | VCC = 1.8V, CS = VCC | 4 |
| Timekeeping current | ICCT | | 1.2 | 1.8 | µA | VCC = 3.0V, CS = VCC | 4 |
| Timekeeping current | ICCT | | | 2.6 | µA | VCC = 3.6V, CS = VCC | 4 |
| Timekeeping backup current | IBATT | | | 850 | nA | VBAT = 1.3V, VCC = VSS | 5 |
| Timekeeping backup current | IBATT | | 1000 | 1200 | nA | VBAT = 3.0V, VCC = VSS | 5 |
| Timekeeping backup current | IBATT | | | 2300 | nA | VBAT = 3.6V, VCC = VSS | 5 |
| VBAT data retention current (oscillator off) | IBATDAT | | | 850 | nA | VBAT = 3.6V, VCC = VSS | 5 |
| Oscillator pin capacitance (X1, X2) | COSC | | 3 | | pF | | 4 |
| Oscillator frequency | FOSC | | 32.768 | | kHz | | 6 |
| Clock frequency | FCLK | | | 5 | MHz | 2.5V ≤ Vcc < 3.6V | 6 |
| Clock frequency | FCLK | | | 3 | MHz | 1.8V ≤ Vcc < 2.5V | 6 |
| CS setup time | TCSS | 100 | | | ns | 2.5V ≤ Vcc < 3.6V | 6 |
| CS setup time | TCSS | 150 | | | ns | 1.8V ≤ Vcc < 2.5V | 6 |
| CS hold time | TCSH | 100 | | | ns | 2.5V ≤ Vcc < 3.6V | 6 |
| CS hold time | TCSH | 150 | | | ns | 1.8V ≤ Vcc < 2.5V | 6 |
| CS disable time | TCSD | 50 | | | ns | | 6 |
| Data setup time | TSU | 20 | | | ns | 2.5V ≤ Vcc < 3.6V | 6 |
| Data setup time | TSU | 30 | | | ns | 1.8V ≤ Vcc < 2.5V | 6 |
| Data hold time | THD | 40 | | | ns | 2.5V ≤ Vcc < 3.6V | 6 |
| Data hold time | THD | 50 | | | ns | 1.8V ≤ Vcc < 2.5V | 6 |
| SCK rise time | TR | | | 100 | ns | | 6 |
| SCK fall time | TF | | | 100 | ns | | 6 |
| Clock high time | THI | 100 | | | ns | 2.5V ≤ Vcc < 3.6V | 6 |
| Clock high time | THI | 150 | | | ns | 1.8V ≤ Vcc < 2.5V | 6 |
| Clock low time | TLO | 100 | | | ns | 2.5V ≤ Vcc < 3.6V | 6 |
| Clock low time | TLO | 150 | | | ns | 1.8V ≤ Vcc < 2.5V | 6 |
| Clock delay time | TCLD | 50 | | | ns | | 6 |
| Clock enable time | TCLE | 50 | | | ns | | 6 |
| Output valid from clock low | TV | | | 100 | ns | 2.5V ≤ Vcc < 3.6V | 6 |
| Output valid from clock low | TV | | | 160 | ns | 1.8V ≤ Vcc < 2.5V | 6 |
| Output hold time | THO | 0 | | | ns | | 6 |
| Output disable time | TDIS | | | 80 | ns | 2.5V ≤ Vcc < 3.6V | 6 |
| Output disable time | TDIS | | | 160 | ns | 1.8V ≤ Vcc < 2.5V | 6 |
| Internal write cycle time | TWC | | | 5 | ms | | 6 |
| VCC fall time | TFVCC | 300 | | | µs | | 6 |
| VCC rise time | TRVCC | 0 | | | µs | | 6 |
| Oscillator timeout period | TOSF | | 1 | | ms | | 6 |
## CAD (KiCad official)
- Symbol: `MCP79510-I`
- Footprint: `Package_SO:MSOP-10_3x3mm_P0.5mm`
- 3D model: MSOP-10 (KiCad packages3D, STEP)
- 3D model files: `mcp79510-i-etched.step` / `mcp79510-i-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mcp79510-i.step` / `mcp79510-i.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](https://ww1.microchip.com/downloads/en/DeviceDoc/MCP7951X-MCP7952X-Battery-Backed-SPI-Real-Time-Clock-Calendar-20002300D.pdf) (58 pp, sha256 `1caaeadd97693b59`, retrieved 2026-10-23, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mcp79510-i-datasheet.pdf)