main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs mcp7940nt-i: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
viewers pin 1: carry the footprint's marker into the .lbr, the viewer and page.json (silk-marker, drawn, top-left) · Ray
mcp7940nt-i-etched.fit.json mcp7940nt-i: re-etch, flat white mark read from pin 1 (service-occt 1.4.0) + chip hero · Ray
mcp7940nt-i-etched.glb mcp7940nt-i: white body in tscircuit (pre-1.8 etch structure under an assembly instance); Ray 2026-10-19: black IC body… · Ray
mcp7940nt-i-etched.step mcp7940nt-i: white body in tscircuit (pre-1.8 etch structure under an assembly instance); Ray 2026-10-19: black IC body… · Ray
mcp7940nt-i-sn-hero.glb Publish 0.1.1 · Ray
mcp7940nt-i-sn-hero.overlay.json Publish 0.1.1 · Ray
mcp7940nt-i.glb Publish 0.1.0 · Ray
mcp7940nt-i.kicad_mod Publish 0.1.0 · Ray
mcp7940nt-i.kicad_sym Publish 0.1.0 · Ray
mcp7940nt-i.lbr mcp7940nt-i-sn: renamed from mcp7940nt-i, the part it was built from (MCP7940NT-I/SN); family listed · Ray
mcp7940nt-i.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
pads.json page.json: drop the phantom "EP" pin. The datasheet package drawing is an 8-lead SOIC with 8 pads and no thermal pad, m… · Ray
page.json Publish 0.1.1 · Ray
README.md mcp7940nt-i-sn: renamed from mcp7940nt-i, the part it was built from (MCP7940NT-I/SN); family listed · Ray

MCP7940NT-I/SN

Microchip · Real-time Clocks (RTC) · SOIC-8

MCP7940NT-I from Microchip, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 X1 input Quartz crystal input / external oscillator input. Connects to one terminal of the 32.768 kHz tuning-fork crystal (optimized for 6-9 pF load capacitance) with its external load capacitor to VSS. Also usable as the external clock input when driving the device from an external oscillator.
2 X2 output Quartz crystal output. Connects to the second terminal of the 32.768 kHz crystal with its external load capacitor to VSS. Leave floating when using an external oscillator driving X1.
3 VBAT power_in Battery backup supply input, 1.3 V to 5.5 V. Maintains RTCC and SRAM when VCC is lost; typical timekeeping backup current is 925 nA at 3.0 V. Tie to VSS if the battery backup feature is not used.
4 VSS power_in Device ground (0 V) reference for VCC and VBAT rails and all logic signals.
5 SDA bidirectional Bidirectional I2C serial data (open-drain). Requires an external pull-up resistor to VCC (typ. 10 kΩ at 100 kHz or 2 kΩ at 400 kHz). Data may change only while SCL is low; changes while SCL is high signal Start/Stop conditions.
6 SCL input I2C serial clock input from the bus master, used to synchronize data transfer to/from the device. Supports clock rates up to 400 kHz. Schmitt-trigger input with 50 ns spike suppression; requires an external pull-up to VCC.
7 MFP output Multifunction output (open-drain). Configurable as alarm output on an alarm match, as a selectable-frequency square-wave output, or as a general-purpose output driven by the OUT bit in the CONTROL register. Requires an external pull-up resistor to VCC (typ. 10 kΩ); leave floating if unused. VOL = 0.40 V at IOL = 3.0 mA (VCC = 4.5 V).
8 VCC power_in Primary power supply, 1.8 V to 5.5 V. Typical timekeeping current 1.2 uA at 3.3 V; SRAM/RTCC register operating current is 300 uA (read) / 400 uA (write) at VCC = 5.5 V, SCL = 400 kHz. Power-fail switchover to VBAT occurs at VTRIP (1.3-1.7 V).
EP EP passive Exposed thermal/mechanical pad on the underside of the TDFN package. May be connected to VSS or left floating (per the Note under Table 3-1). Connection to VSS is recommended for mechanical anchoring and improved thermal performance.

Key specifications

Parameter Value
Manufacturer Microchip
Package SOIC-8
Category RTC
Pins 9

Ordering variants

Same part, different packaging or reel option.

  • MCP7940NT-IMNY
  • MCP7940NT-I/MNY
  • MCP7940NT-ISN
  • MCP7940NT-IMS
  • MCP7940NT-IST
  • MCP7940NT-IP

CAD (KiCad official)

  • Symbol: MCP7940NT-I
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: mcp7940nt-i-etched.step / mcp7940nt-i-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp7940nt-i.step / mcp7940nt-i.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip datasheet (56 pp, sha256 4aafe310fbafe313, retrieved 2026-08-17, tier: manufacturer)
  • Extractor: ds2sf (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF

Other parts in this family

This page is MCP7940NT-I/SN. These part numbers share its family name but are different parts (another package, rating or grade), each with its own page:

  • MCP7940NT-I/MS