main
Ray mcp7940nt-e-ms: renamed from mcp7940nt-e, the part it was built from (MCP7940NT-E/MS); family listed 788b29a

MCP7940NT-E/MS

Microchip Tech · Real-time Clocks (RTC) · MSOP-8

MCP7940NT-E from Microchip Tech, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 X1 input Quartz crystal input for the 32.768 kHz crystal (6-9 pF load), also serves as the external clock input when EXTOSC is set.
2 X2 passive Quartz crystal output for the 32.768 kHz crystal; leave floating when an external clock is used on X1.
3 VBAT power_in Backup supply input (1.3V to 5.5V) maintaining RTCC and SRAM when VCC is unavailable; connect to VSS if battery backup is not used.
4 VSS power_in Ground.
5 SDA bidirectional Bidirectional open-drain I2C serial data pin for addresses and data, requiring a pull-up resistor to VCC (typically 10 kΩ for 100 kHz, 2 kΩ for 400 kHz).
6 SCL input I2C serial clock input used to synchronize data transfer to and from the device.
7 MFP output Open-drain multifunction output for alarm, square wave or general purpose output (OUT bit), requiring a pull-up to VCC (typically 10 kΩ) and may be left floating if unused.
8 VCC power_in Primary power supply with operating range of 1.8V to 5.5V.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package MSOP-8
Category RTC/Clock Chip
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VCC supply VCC 6.5 V 3
SDA and SCL w.r.t. VSS -0.6 6.5 V 3
Storage temperature -65 150 °C 3
Ambient temperature with power applied -40 125 °C 3
ESD protection on all pins 4 kV 3
Operating voltage VCC 1.8 5.5 V Extended (E) 3
Operating temperature (Extended) TA -40 125 °C Extended (E) 3
High-Level Input Voltage VIH 0.7 V 0.7 VCC 3
Low-Level Input Voltage VIL 0.3 V 0.3 VCC, VCC ≥ 2.5V 3
Low-Level Input Voltage VIL 0.2 V 0.2 VCC, VCC < 2.5V 3
Hysteresis of Schmitt Trigger Inputs (SDA, SCL) VHYS 0.05 V 0.05 VCC, Note 2 3
Low-Level Output Voltage (MFP, SDA) VOL 0.4 V IOL = 3.0 mA @ VCC = 4.5V; IOL = 2.1 mA @ VCC = 2.5V 3
Input Leakage Current ILI -1 1 µA VIN = VSS or VCC 3
Output Leakage Current ILO -1 1 µA VOUT = VSS or VCC 3
Pin Capacitance (SDA, SCL, MFP) CIN, COUT 10 pF VCC = 5.0V (Note 2), TA = +25°C, f = 1 MHz 3
Oscillator Pin Capacitance (X1, X2) COSC 3 pF Note 2 3
SRAM/RTCC Register Operating Current (read) ICCREAD 300 µA VCC = 5.5V, SCL = 400 kHz 3
SRAM/RTCC Register Operating Current (write) ICCWRITE 400 µA VCC = 5.5V, SCL = 400 kHz 3
VCC Data-Retention Current (oscillator off) ICCDAT 5 µA SCL, SDA, VCC = 5.5V (E-temp) 3
Timekeeping Current ICCT 1.2 µA VCC = 3.3V (Note 2) 3
Power-fail Switchover Voltage VTRIP 1.3 1.5 1.7 V 3
Backup Supply Voltage Range VBAT 1.3 5.5 V Note 2 3
Timekeeping Backup Current IBATT 850 nA VBAT = 1.3V, VCC = VSS (Note 2) 4
Timekeeping Backup Current IBATT 925 1200 nA VBAT = 3.0V, VCC = VSS (Note 2) 4
Timekeeping Backup Current IBATT 9000 nA VBAT = 5.5V, VCC = VSS (Note 2) 4
VBAT Data Retention Current (oscillator off) IBATDAT 750 nA VBAT = 3.6V, VCC = VSS 4
Clock Frequency FCLK 100 kHz 1.8V ≤ VCC < 2.5V 5
Clock Frequency FCLK 400 kHz 2.5V ≤ VCC ≤ 5.5V 5
Clock High Time THIGH 4000 ns 1.8V ≤ VCC < 2.5V 5
Clock High Time THIGH 600 ns 2.5V ≤ VCC ≤ 5.5V 5
Clock Low Time TLOW 4700 ns 1.8V ≤ VCC < 2.5V 5
Clock Low Time TLOW 1300 ns 2.5V ≤ VCC ≤ 5.5V 5
SDA and SCL Rise Time TR 1000 ns 1.8V ≤ VCC < 2.5V (Note 1) 5
SDA and SCL Rise Time TR 300 ns 2.5V ≤ VCC ≤ 5.5V (Note 1) 5
SDA and SCL Fall Time TF 1000 ns 1.8V ≤ VCC < 2.5V (Note 1) 5
SDA and SCL Fall Time TF 300 ns 2.5V ≤ VCC ≤ 5.5V (Note 1) 5
Start Condition Hold Time THD:STA 4000 ns 1.8V ≤ VCC < 2.5V 5
Start Condition Hold Time THD:STA 600 ns 2.5V ≤ VCC ≤ 5.5V 5
Start Condition Setup Time TSU:STA 4700 ns 1.8V ≤ VCC < 2.5V 5
Start Condition Setup Time TSU:STA 600 ns 2.5V ≤ VCC ≤ 5.5V 5
Data Input Hold Time THD:DAT 0 ns Note 2 5
Data Input Setup Time TSU:DAT 250 ns 1.8V ≤ VCC < 2.5V 5
Data Input Setup Time TSU:DAT 100 ns 2.5V ≤ VCC ≤ 5.5V 5
Stop Condition Setup Time TSU:STO 4000 ns 1.8V ≤ VCC < 2.5V 5
Stop Condition Setup Time TSU:STO 600 ns 2.5V ≤ VCC ≤ 5.5V 5
Output Valid From Clock TAA 3500 ns 1.8V ≤ VCC < 2.5V 5
Output Valid From Clock TAA 900 ns 2.5V ≤ VCC ≤ 5.5V 5
Bus free time TBUF 4700 ns 1.8V ≤ VCC < 2.5V 5
Bus free time TBUF 1300 ns 2.5V ≤ VCC ≤ 5.5V 5
Input Filter Spike Suppression (SDA, SCL) TSP 50 ns Note 1 5
VCC fall time TFVCC 300 µs Note 1 5
VCC rise time TRVCC 0 µs Note 1 5
Oscillator timeout period TOSF 1 ms Note 1 5
Oscillator frequency FOSC 32.768 kHz 5

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 44

CAD (KiCad official)

  • Symbol: MCP7940NT-E
  • Footprint: Package_SO:MSOP-8_3x3mm_P0.65mm
  • 3D model: MSOP-8 (KiCad packages3D, STEP)
  • 3D model files: mcp7940nt-e-etched.step / mcp7940nt-e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp7940nt-e.step / mcp7940nt-e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (58 pp, sha256 92385d740e31ab2b, retrieved 2026-10-23, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF

Other parts in this family

This page is MCP7940NT-E/MS. These part numbers share its family name but are different parts (another package, rating or grade), each with its own page:

  • MCP7940NT-E/SN