main
Ray
mcp7940m-i-ms: renamed from mcp7940m-i, the part it was built from (MCP7940M-I/MS); family listed
964fc7b
MCP7940M-I/MS
Microchip Tech · Real-time Clocks (RTC) · MSOP-8
MCP7940M-I from Microchip Tech, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | X1 | input | Quartz crystal input for the 32.768 kHz crystal (6-9 pF load), also serves as the external clock input when EXTOSC is set. |
| 2 | X2 | output | Quartz crystal output for the external 32.768 kHz crystal; leave floating when an external clock is used on X1. |
| 3 | NC | unconnected | Not connected. |
| 4 | VSS | power_in | Ground. |
| 5 | SDA | bidirectional | Open-drain bidirectional I2C serial data pin that needs a pull-up resistor to VCC (typically 10 kΩ for 100 kHz, 2 kΩ for 400 kHz). |
| 6 | SCL | input | I2C serial clock input used to synchronize data transfer to and from the device (up to 400 kHz). |
| 7 | MFP | output | Open-drain multifunction output for alarm, square wave or general purpose output (OUT bit); requires a pull-up to VCC (typically 10 kΩ) and may be left floating if unused. |
| 8 | VCC | power_in | Primary power supply, operating range 1.8V to 5.5V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-8 |
| Category | RTC/Clock Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| High-level input voltage | VIH | 0.7 | V | min is 0.7 VCC | 3 | ||
| Low-level input voltage (VCC ≥ 2.5V) | VIL | 0.3 | V | max is 0.3 VCC; VCC ≥ 2.5V | 3 | ||
| Low-level input voltage (VCC < 2.5V) | VIL | 0.2 | V | max is 0.2 VCC; VCC < 2.5V | 3 | ||
| Hysteresis of Schmitt Trigger inputs (SDA, SCL) | VHYS | 0.05 | V | min is 0.05 VCC; Note 1 | 3 | ||
| Low-level output voltage (MFP, SDA) | VOL | 0.4 | V | IOL = 3.0 mA @ VCC = 4.5V; IOL = 2.1 mA @ VCC = 2.5V | 3 | ||
| Input leakage current | ILI | -1 | 1 | µA | VIN = VSS or VCC | 3 | |
| Output leakage current | ILO | -1 | 1 | µA | VOUT = VSS or VCC | 3 | |
| Pin capacitance (SDA, SCL, MFP) | CIN, COUT | 10 | pF | VCC = 5.0V (Note 1); TA = 25°C, f = 1 MHz | 3 | ||
| SRAM/RTCC register operating current (read) | ICCREAD | 300 | µA | VCC = 5.5V, SCL = 400 kHz | 3 | ||
| SRAM/RTCC register operating current (write) | ICCWRITE | 400 | µA | VCC = 5.5V, SCL = 400 kHz | 3 | ||
| VCC data-retention current (oscillator off) | ICCDAT | 1 | µA | SCL, SDA, VCC = 5.5V | 3 | ||
| Clock frequency | FCLK | 100 | kHz | 1.8V ≤ VCC < 2.5V | 4 | ||
| Clock frequency | FCLK | 400 | kHz | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| Clock high time | THIGH | 4000 | ns | 1.8V ≤ VCC < 2.5V | 4 | ||
| Clock high time | THIGH | 600 | ns | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| Clock low time | TLOW | 4700 | ns | 1.8V ≤ VCC < 2.5V | 4 | ||
| Clock low time | TLOW | 1300 | ns | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| SDA and SCL rise time | TR | 1000 | ns | 1.8V ≤ VCC < 2.5V (Note 1) | 4 | ||
| SDA and SCL rise time | TR | 300 | ns | 2.5V ≤ VCC ≤ 5.5V (Note 1) | 4 | ||
| SDA and SCL fall time | TF | 1000 | ns | 1.8V ≤ VCC < 2.5V (Note 1) | 4 | ||
| SDA and SCL fall time | TF | 300 | ns | 2.5V ≤ VCC ≤ 5.5V (Note 1) | 4 | ||
| Start condition hold time | THD:STA | 4000 | ns | 1.8V ≤ VCC < 2.5V | 4 | ||
| Start condition hold time | THD:STA | 600 | ns | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| Start condition setup time | TSU:STA | 4700 | ns | 1.8V ≤ VCC < 2.5V | 4 | ||
| Start condition setup time | TSU:STA | 600 | ns | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| Data input hold time | THD:DAT | 0 | ns | Note 2 | 4 | ||
| Data input setup time | TSU:DAT | 250 | ns | 1.8V ≤ VCC < 2.5V | 4 | ||
| Data input setup time | TSU:DAT | 100 | ns | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| Stop condition setup time | TSU:STO | 4000 | ns | 1.8V ≤ VCC < 2.5V | 4 | ||
| Stop condition setup time | TSU:STO | 600 | ns | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| Output valid from clock | TAA | 3500 | ns | 1.8V ≤ VCC < 2.5V | 4 | ||
| Output valid from clock | TAA | 900 | ns | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| Bus free time | TBUF | 4700 | ns | 1.8V ≤ VCC < 2.5V | 4 | ||
| Bus free time | TBUF | 1300 | ns | 2.5V ≤ VCC ≤ 5.5V | 4 | ||
| Input filter spike suppression (SDA and SCL) | TSP | 50 | ns | Note 1 | 4 | ||
| Oscillator timeout period | TOSF | 1 | ms | Note 1 | 4 | ||
| Supply voltage | VCC | 6.5 | V | 3 | |||
| All inputs and outputs (except SDA and SCL) w.r.t. VSS | -0.6 | V | -0.6V to VCC +1.0V | 3 | |||
| SDA and SCL w.r.t. VSS | -0.6 | 6.5 | V | 3 | |||
| Storage temperature | -65 | 150 | °C | 3 | |||
| Ambient temperature with power applied | -40 | 125 | °C | 3 | |||
| Operating voltage range | VCC | 1.8 | 5.5 | V | Industrial (I) | 3 | |
| Operating temperature | TA | -40 | 85 | °C | Industrial (I) | 3 | |
| Oscillator pin capacitance (X1, X2) | COSC | 3 | pF | Note 1 | 3 | ||
| Timekeeping current | ICCT | 1.2 | µA | VCC = 3.3V (Note 1) | 3 | ||
| Oscillator frequency | FOSC | 32.768 | kHz | 4 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 | 33 |
CAD (KiCad official)
- Symbol:
MCP7940M-I - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
mcp7940m-i-etched.step/mcp7940m-i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp7940m-i.step/mcp7940m-i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (50 pp, sha256
618ec2c897719bef, retrieved 2026-10-26, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
Other parts in this family
This page is MCP7940M-I/MS. These part numbers share its family name but are different parts (another package, rating or grade), each with its own page:
- MCP7940M-I/SN
- MCP7940M-I/ST
# MCP7940M-I/MS
**Microchip Tech** · Real-time Clocks (RTC) · MSOP-8
MCP7940M-I from Microchip Tech, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | X1 | input | Quartz crystal input for the 32.768 kHz crystal (6-9 pF load), also serves as the external clock input when EXTOSC is set. |
| 2 | X2 | output | Quartz crystal output for the external 32.768 kHz crystal; leave floating when an external clock is used on X1. |
| 3 | NC | unconnected | Not connected. |
| 4 | VSS | power_in | Ground. |
| 5 | SDA | bidirectional | Open-drain bidirectional I2C serial data pin that needs a pull-up resistor to VCC (typically 10 kΩ for 100 kHz, 2 kΩ for 400 kHz). |
| 6 | SCL | input | I2C serial clock input used to synchronize data transfer to and from the device (up to 400 kHz). |
| 7 | MFP | output | Open-drain multifunction output for alarm, square wave or general purpose output (OUT bit); requires a pull-up to VCC (typically 10 kΩ) and may be left floating if unused. |
| 8 | VCC | power_in | Primary power supply, operating range 1.8V to 5.5V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-8 |
| Category | RTC/Clock Chip |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| High-level input voltage | VIH | 0.7 | | | V | min is 0.7 VCC | 3 |
| Low-level input voltage (VCC ≥ 2.5V) | VIL | | | 0.3 | V | max is 0.3 VCC; VCC ≥ 2.5V | 3 |
| Low-level input voltage (VCC < 2.5V) | VIL | | | 0.2 | V | max is 0.2 VCC; VCC < 2.5V | 3 |
| Hysteresis of Schmitt Trigger inputs (SDA, SCL) | VHYS | 0.05 | | | V | min is 0.05 VCC; Note 1 | 3 |
| Low-level output voltage (MFP, SDA) | VOL | | | 0.4 | V | IOL = 3.0 mA @ VCC = 4.5V; IOL = 2.1 mA @ VCC = 2.5V | 3 |
| Input leakage current | ILI | -1 | | 1 | µA | VIN = VSS or VCC | 3 |
| Output leakage current | ILO | -1 | | 1 | µA | VOUT = VSS or VCC | 3 |
| Pin capacitance (SDA, SCL, MFP) | CIN, COUT | | | 10 | pF | VCC = 5.0V (Note 1); TA = 25°C, f = 1 MHz | 3 |
| SRAM/RTCC register operating current (read) | ICCREAD | | | 300 | µA | VCC = 5.5V, SCL = 400 kHz | 3 |
| SRAM/RTCC register operating current (write) | ICCWRITE | | | 400 | µA | VCC = 5.5V, SCL = 400 kHz | 3 |
| VCC data-retention current (oscillator off) | ICCDAT | | | 1 | µA | SCL, SDA, VCC = 5.5V | 3 |
| Clock frequency | FCLK | | | 100 | kHz | 1.8V ≤ VCC < 2.5V | 4 |
| Clock frequency | FCLK | | | 400 | kHz | 2.5V ≤ VCC ≤ 5.5V | 4 |
| Clock high time | THIGH | 4000 | | | ns | 1.8V ≤ VCC < 2.5V | 4 |
| Clock high time | THIGH | 600 | | | ns | 2.5V ≤ VCC ≤ 5.5V | 4 |
| Clock low time | TLOW | 4700 | | | ns | 1.8V ≤ VCC < 2.5V | 4 |
| Clock low time | TLOW | 1300 | | | ns | 2.5V ≤ VCC ≤ 5.5V | 4 |
| SDA and SCL rise time | TR | | | 1000 | ns | 1.8V ≤ VCC < 2.5V (Note 1) | 4 |
| SDA and SCL rise time | TR | | | 300 | ns | 2.5V ≤ VCC ≤ 5.5V (Note 1) | 4 |
| SDA and SCL fall time | TF | | | 1000 | ns | 1.8V ≤ VCC < 2.5V (Note 1) | 4 |
| SDA and SCL fall time | TF | | | 300 | ns | 2.5V ≤ VCC ≤ 5.5V (Note 1) | 4 |
| Start condition hold time | THD:STA | 4000 | | | ns | 1.8V ≤ VCC < 2.5V | 4 |
| Start condition hold time | THD:STA | 600 | | | ns | 2.5V ≤ VCC ≤ 5.5V | 4 |
| Start condition setup time | TSU:STA | 4700 | | | ns | 1.8V ≤ VCC < 2.5V | 4 |
| Start condition setup time | TSU:STA | 600 | | | ns | 2.5V ≤ VCC ≤ 5.5V | 4 |
| Data input hold time | THD:DAT | 0 | | | ns | Note 2 | 4 |
| Data input setup time | TSU:DAT | 250 | | | ns | 1.8V ≤ VCC < 2.5V | 4 |
| Data input setup time | TSU:DAT | 100 | | | ns | 2.5V ≤ VCC ≤ 5.5V | 4 |
| Stop condition setup time | TSU:STO | 4000 | | | ns | 1.8V ≤ VCC < 2.5V | 4 |
| Stop condition setup time | TSU:STO | 600 | | | ns | 2.5V ≤ VCC ≤ 5.5V | 4 |
| Output valid from clock | TAA | | | 3500 | ns | 1.8V ≤ VCC < 2.5V | 4 |
| Output valid from clock | TAA | | | 900 | ns | 2.5V ≤ VCC ≤ 5.5V | 4 |
| Bus free time | TBUF | 4700 | | | ns | 1.8V ≤ VCC < 2.5V | 4 |
| Bus free time | TBUF | 1300 | | | ns | 2.5V ≤ VCC ≤ 5.5V | 4 |
| Input filter spike suppression (SDA and SCL) | TSP | | | 50 | ns | Note 1 | 4 |
| Oscillator timeout period | TOSF | 1 | | | ms | Note 1 | 4 |
| Supply voltage | VCC | | | 6.5 | V | | 3 |
| All inputs and outputs (except SDA and SCL) w.r.t. VSS | | -0.6 | | | V | -0.6V to VCC +1.0V | 3 |
| SDA and SCL w.r.t. VSS | | -0.6 | | 6.5 | V | | 3 |
| Storage temperature | | -65 | | 150 | °C | | 3 |
| Ambient temperature with power applied | | -40 | | 125 | °C | | 3 |
| Operating voltage range | VCC | 1.8 | | 5.5 | V | Industrial (I) | 3 |
| Operating temperature | TA | -40 | | 85 | °C | Industrial (I) | 3 |
| Oscillator pin capacitance (X1, X2) | COSC | | 3 | | pF | Note 1 | 3 |
| Timekeeping current | ICCT | | 1.2 | | µA | VCC = 3.3V (Note 1) | 3 |
| Oscillator frequency | FOSC | | 32.768 | | kHz | | 4 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | | tin | 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] A A2 | 33 |
## CAD (KiCad official)
- Symbol: `MCP7940M-I`
- Footprint: `Package_SO:MSOP-8_3x3mm_P0.65mm`
- 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files: `mcp7940m-i-etched.step` / `mcp7940m-i-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mcp7940m-i.step` / `mcp7940m-i.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/mcp7940m-i-datasheet.pdf) (50 pp, sha256 `618ec2c897719bef`, retrieved 2026-10-26, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mcp7940m-i-datasheet.pdf)
## Other parts in this family
This page is **MCP7940M-I/MS**. These part numbers share its family name but are different parts (another package, rating or grade), each with its own page:
- MCP7940M-I/SN
- MCP7940M-I/ST