main
Ray
Publish 0.1.0
942dc30
MCP73855-I
Microchip Tech · Battery Management ICs · DFN-10-EP(3x3)
MCP73855-I from Microchip Tech, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | STAT1 | output | Charge status output is a current-limited open-drain drive for direct connection to an LED, or it can use a pull-up resistor to interface with a host microcontroller. |
| 2 | VSET | input | Voltage regulation selection: connect to VSS for 4.1V regulation voltage or to VDD for 4.2V regulation voltage. |
| 3 | VDD1 | power_in | Battery management input supply; a supply of [VREG(Typ) + 0.3V] to 5.5V is recommended, bypassed to VSS with a minimum of 4.7 µF. |
| 4 | VSS1 | power_in | Battery management 0V reference, to be connected to the negative terminal of the battery. |
| 5 | PROG | passive | Current regulation set: a resistor from PROG to VSS scales the preconditioning, fast-charge and termination currents. |
| 6 | TIMER | passive | Timer set: all safety timers are scaled by CTIMER/0.1 µF, where CTIMER is the external capacitor on this pin. |
| 7 | VSS2 | power_in | Battery management 0V reference, to be connected to the negative terminal of the battery. |
| 8 | VBAT1 | power_out | Battery charge control output connected to the positive battery terminal; it is the drain of the internal P-channel pass transistor and needs a minimum 4.7 µF bypass to VSS for loop stability when the battery is disconnected. |
| 9 | VBAT2 | power_out | Battery charge control output connected to the positive battery terminal; it is the drain of the internal P-channel pass transistor and needs a minimum 4.7 µF bypass to VSS for loop stability when the battery is disconnected. |
| 10 | EN | input | Logic enable input used to force charge termination, initiate a charge, clear faults, or disable automatic recharge. |
| 11 | EP | power_in | Exposed pad, which is at VSS potential and should be connected to VSS. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | DFN-10-EP(3x3) |
| Category | Power Management |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (VDD1,2) absolute maximum | VDD1,2 | 6.5 | V | 3 | |||
| All Inputs and Outputs w.r.t. VSS | -0.3 | V | 3 | ||||
| ESD protection, Human Body Model | 4 | kV | Human Body Model (1.5k in series with 100pF) | 3 | |||
| ESD protection, Machine Model | 400 | V | Machine Model (200pF, no series resistance) | 3 | |||
| Supply Voltage | VDD | 4.5 | 5.5 | V | 3 | ||
| Supply Current (disabled) | ISS | 0.28 | 4 | µA | Disabled | 3 | |
| Supply Current (operating) | ISS | 0.83 | 4 | mA | Operating | 3 | |
| UVLO Start Threshold | VSTART | 4.25 | 4.45 | 4.65 | V | VDD Low-to-High | 3 |
| UVLO Stop Threshold | VSTOP | 4.2 | 4.4 | 4.55 | V | VDD High-to-Low | 3 |
| Regulated Output Voltage (4.1V option) | VREG | 4.079 | 4.1 | 4.121 | V | VSET = VSS | 3 |
| Regulated Output Voltage (4.2V option) | VREG | 4.179 | 4.2 | 4.221 | V | VSET = VDD; VDD = [VREG(Typ) + 1V], IOUT = 10 mA, TA = -5°C to +55°C (printed note below this row) | 3 |
| Line Regulation | ΔVBAT/(VBAT·ΔVDD) | 0.02 | 0.25 | %/V | VDD = [VREG(Typ) + 1V] to 5.5V; IOUT = 10 mA | 3 | |
| Load Regulation | ΔVBAT/VBAT | 0.022 | 0.25 | % | IOUT = 10 mA to 150 mA; VDD = [VREG(Typ) + 1V] | 3 | |
| Output Reverse-Leakage Current | IDISCHARGE | 0.24 | 1 | µA | VDD < VBAT = VREG(Typ) | 3 | |
| Fast Charge Current Regulation (PROG open) | IREG | 70 | 85 | 100 | mA | PROG = OPEN | 3 |
| Fast Charge Current Regulation (PROG = VSS) | IREG | 325 | 400 | 475 | mA | PROG = VSS; TA = -5°C to +55°C | 3 |
| Precondition Current Regulation (PROG open) | IPREG | 5 | 9 | 15 | mA | PROG = OPEN | 3 |
| Precondition Current Regulation (PROG = VSS) | IPREG | 25 | 40 | 75 | mA | PROG = VSS; TA = -5°C to +55°C | 3 |
| Precondition Threshold Voltage (VSET = VSS) | VPTH | 2.7 | 2.8 | 2.9 | V | VSET = VSS; VBAT Low-to-High | 3 |
| Precondition Threshold Voltage (VSET = VDD) | VPTH | 2.75 | 2.85 | 2.95 | V | VSET = VDD; VBAT Low-to-High | 3 |
| Charge Termination Current (PROG open) | ITERM | 3.7 | 6.5 | 9.3 | mA | PROG = OPEN | 4 |
| Charge Termination Current (PROG = VSS) | ITERM | 18 | 32 | 46 | mA | PROG = VSS; TA = -5°C to +55°C | 4 |
| Status Indicator STAT1 Sink Current | ISINK | 4 | 8 | 12 | mA | 4 | |
| Status Indicator Low Output Voltage | VOL | 200 | 400 | mV | ISINK = 1 mA | 4 | |
| Status Input Leakage Current | ILK | 0.01 | 1 | µA | ISINK = 0 mA, VSTAT1,2 = 5.5V | 4 | |
| Enable Input High Voltage Level | VIH | 1.4 | V | 4 | |||
| Enable Input Low Voltage Level | VIL | 0.8 | V | 4 | |||
| Enable Input Leakage Current | ILK | 0.01 | 1 | µA | VENABLE = 5.5V | 4 | |
| UVLO Start Delay | tSTART | 5 | ms | VDD Low-to-High | 5 | ||
| Transition Time Out of Preconditioning | tDELAY | 1 | ms | VBAT < VPTH to VBAT > VPTH | 5 | ||
| Current Rise Time Out of Preconditioning | tRISE | 1 | ms | IOUT Rising to 90% of IREG | 5 | ||
| Fast Charge Safety Timer Period | tFAST | 1.1 | 1.5 | 1.9 | Hours | CTIMER = 0.1 µF | 5 |
| Preconditioning Charge Safety Timer Period | tPRECON | 45 | 60 | 75 | Minutes | CTIMER = 0.1 µF | 5 |
| Elapsed Time Termination Period | tTERM | 2.2 | 3 | 3.8 | Hours | CTIMER = 0.1 µF | 5 |
| Status Output Turn-off Time | tOFF | 200 | µs | ISINK = 1 mA to 0 mA | 5 | ||
| Status Output Turn-on Time | tON | 200 | µs | ISINK = 0 mA to 1 mA | 5 | ||
| Specified Temperature Range | TA | -40 | 85 | °C | 5 | ||
| Operating Temperature Range | TJ | -40 | 125 | °C | 5 | ||
| Storage Temperature Range | TA | -65 | 150 | °C | 5 | ||
| Thermal Resistance, 10-L 3x3 mm DFN, junction-to-ambient | JA | 51 | °C/W | 4-Layer JC51-7 Standard Board, Natural Convection | 5 |
CAD (KiCad official)
- Symbol:
MCP73855-I - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
mcp73855-i-etched.step/mcp73855-i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp73855-i.step/mcp73855-i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (32 pp, sha256
58fc7769055374e6, retrieved 2026-11-05, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MCP73855-I
**Microchip Tech** · Battery Management ICs · DFN-10-EP(3x3)
MCP73855-I from Microchip Tech, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | STAT1 | output | Charge status output is a current-limited open-drain drive for direct connection to an LED, or it can use a pull-up resistor to interface with a host microcontroller. |
| 2 | VSET | input | Voltage regulation selection: connect to VSS for 4.1V regulation voltage or to VDD for 4.2V regulation voltage. |
| 3 | VDD1 | power_in | Battery management input supply; a supply of [VREG(Typ) + 0.3V] to 5.5V is recommended, bypassed to VSS with a minimum of 4.7 µF. |
| 4 | VSS1 | power_in | Battery management 0V reference, to be connected to the negative terminal of the battery. |
| 5 | PROG | passive | Current regulation set: a resistor from PROG to VSS scales the preconditioning, fast-charge and termination currents. |
| 6 | TIMER | passive | Timer set: all safety timers are scaled by CTIMER/0.1 µF, where CTIMER is the external capacitor on this pin. |
| 7 | VSS2 | power_in | Battery management 0V reference, to be connected to the negative terminal of the battery. |
| 8 | VBAT1 | power_out | Battery charge control output connected to the positive battery terminal; it is the drain of the internal P-channel pass transistor and needs a minimum 4.7 µF bypass to VSS for loop stability when the battery is disconnected. |
| 9 | VBAT2 | power_out | Battery charge control output connected to the positive battery terminal; it is the drain of the internal P-channel pass transistor and needs a minimum 4.7 µF bypass to VSS for loop stability when the battery is disconnected. |
| 10 | EN | input | Logic enable input used to force charge termination, initiate a charge, clear faults, or disable automatic recharge. |
| 11 | EP | power_in | Exposed pad, which is at VSS potential and should be connected to VSS. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | DFN-10-EP(3x3) |
| Category | Power Management |
| Pins | 11 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (VDD1,2) absolute maximum | VDD1,2 | | | 6.5 | V | | 3 |
| All Inputs and Outputs w.r.t. VSS | | -0.3 | | | V | | 3 |
| ESD protection, Human Body Model | | | | 4 | kV | Human Body Model (1.5k in series with 100pF) | 3 |
| ESD protection, Machine Model | | | | 400 | V | Machine Model (200pF, no series resistance) | 3 |
| Supply Voltage | VDD | 4.5 | | 5.5 | V | | 3 |
| Supply Current (disabled) | ISS | | 0.28 | 4 | µA | Disabled | 3 |
| Supply Current (operating) | ISS | | 0.83 | 4 | mA | Operating | 3 |
| UVLO Start Threshold | VSTART | 4.25 | 4.45 | 4.65 | V | VDD Low-to-High | 3 |
| UVLO Stop Threshold | VSTOP | 4.2 | 4.4 | 4.55 | V | VDD High-to-Low | 3 |
| Regulated Output Voltage (4.1V option) | VREG | 4.079 | 4.1 | 4.121 | V | VSET = VSS | 3 |
| Regulated Output Voltage (4.2V option) | VREG | 4.179 | 4.2 | 4.221 | V | VSET = VDD; VDD = [VREG(Typ) + 1V], IOUT = 10 mA, TA = -5°C to +55°C (printed note below this row) | 3 |
| Line Regulation | ΔVBAT/(VBAT·ΔVDD) | | 0.02 | 0.25 | %/V | VDD = [VREG(Typ) + 1V] to 5.5V; IOUT = 10 mA | 3 |
| Load Regulation | ΔVBAT/VBAT | | 0.022 | 0.25 | % | IOUT = 10 mA to 150 mA; VDD = [VREG(Typ) + 1V] | 3 |
| Output Reverse-Leakage Current | IDISCHARGE | | 0.24 | 1 | µA | VDD < VBAT = VREG(Typ) | 3 |
| Fast Charge Current Regulation (PROG open) | IREG | 70 | 85 | 100 | mA | PROG = OPEN | 3 |
| Fast Charge Current Regulation (PROG = VSS) | IREG | 325 | 400 | 475 | mA | PROG = VSS; TA = -5°C to +55°C | 3 |
| Precondition Current Regulation (PROG open) | IPREG | 5 | 9 | 15 | mA | PROG = OPEN | 3 |
| Precondition Current Regulation (PROG = VSS) | IPREG | 25 | 40 | 75 | mA | PROG = VSS; TA = -5°C to +55°C | 3 |
| Precondition Threshold Voltage (VSET = VSS) | VPTH | 2.7 | 2.8 | 2.9 | V | VSET = VSS; VBAT Low-to-High | 3 |
| Precondition Threshold Voltage (VSET = VDD) | VPTH | 2.75 | 2.85 | 2.95 | V | VSET = VDD; VBAT Low-to-High | 3 |
| Charge Termination Current (PROG open) | ITERM | 3.7 | 6.5 | 9.3 | mA | PROG = OPEN | 4 |
| Charge Termination Current (PROG = VSS) | ITERM | 18 | 32 | 46 | mA | PROG = VSS; TA = -5°C to +55°C | 4 |
| Status Indicator STAT1 Sink Current | ISINK | 4 | 8 | 12 | mA | | 4 |
| Status Indicator Low Output Voltage | VOL | | 200 | 400 | mV | ISINK = 1 mA | 4 |
| Status Input Leakage Current | ILK | | 0.01 | 1 | µA | ISINK = 0 mA, VSTAT1,2 = 5.5V | 4 |
| Enable Input High Voltage Level | VIH | 1.4 | | | V | | 4 |
| Enable Input Low Voltage Level | VIL | | | 0.8 | V | | 4 |
| Enable Input Leakage Current | ILK | | 0.01 | 1 | µA | VENABLE = 5.5V | 4 |
| UVLO Start Delay | tSTART | | | 5 | ms | VDD Low-to-High | 5 |
| Transition Time Out of Preconditioning | tDELAY | | | 1 | ms | VBAT < VPTH to VBAT > VPTH | 5 |
| Current Rise Time Out of Preconditioning | tRISE | | | 1 | ms | IOUT Rising to 90% of IREG | 5 |
| Fast Charge Safety Timer Period | tFAST | 1.1 | 1.5 | 1.9 | Hours | CTIMER = 0.1 µF | 5 |
| Preconditioning Charge Safety Timer Period | tPRECON | 45 | 60 | 75 | Minutes | CTIMER = 0.1 µF | 5 |
| Elapsed Time Termination Period | tTERM | 2.2 | 3 | 3.8 | Hours | CTIMER = 0.1 µF | 5 |
| Status Output Turn-off Time | tOFF | | | 200 | µs | ISINK = 1 mA to 0 mA | 5 |
| Status Output Turn-on Time | tON | | | 200 | µs | ISINK = 0 mA to 1 mA | 5 |
| Specified Temperature Range | TA | -40 | | 85 | °C | | 5 |
| Operating Temperature Range | TJ | -40 | | 125 | °C | | 5 |
| Storage Temperature Range | TA | -65 | | 150 | °C | | 5 |
| Thermal Resistance, 10-L 3x3 mm DFN, junction-to-ambient | JA | | 51 | | °C/W | 4-Layer JC51-7 Standard Board, Natural Convection | 5 |
## CAD (KiCad official)
- Symbol: `MCP73855-I`
- Footprint: `Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm`
- 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files: `mcp73855-i-etched.step` / `mcp73855-i-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mcp73855-i.step` / `mcp73855-i.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/mcp73855-i-datasheet.pdf) (32 pp, sha256 `58fc7769055374e6`, retrieved 2026-11-05, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mcp73855-i-datasheet.pdf)