main
Ray Publish 0.1.0 30e0d13

MCP73842T-840I

Microchip Tech · Battery Management ICs · MSOP-10

MCP73842T-840I from Microchip Tech, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SENSE input Charge current sense input, connected across an external precision sense resistor between VDD and the external pass transistor Q1; a 220 m sense resistor produces a typical fast charge current of 500 mA.
2 VDD power_in Battery management input supply, recommended at [VREG(Typ) + 0.3V] to 12V and bypassed to VSS with a minimum of 4.7 µF.
3 STAT1 output Current-limited open-drain charge status output that can drive an LED directly or interface to a host microcontroller through a pull-up resistor.
4 EN input Logic enable input used to force charge termination, initiate a charge, clear faults, or disable automatic recharge.
5 THREF power_out Voltage reference that biases the external thermistor for continuous cell temperature monitoring and pre-qualification (MCP73841/MCP73842 only).
6 THERM input Input for the external thermistor used for continuous cell temperature monitoring and pre-qualification, where applying 0.85V disables temperature sensing (MCP73841/MCP73842 only).
7 TIMER passive Timer set pin where all safety timers are scaled by CTIMER/0.1 µF.
8 VSS power_in Battery management 0V reference, connected to the negative terminal of the battery.
9 VBAT power_in Battery voltage sense input connected to the positive battery terminal, bypassed to VSS with a minimum of 4.7 µF for loop stability, with an internal divider regulating this pin to VREG.
10 DRV output Direct output drive of an external P-channel MOSFET for current and voltage regulation.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package MSOP-10
Category Power Supply Chip
Pins 10

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage (MCP73842, MCP73844) VDD 8.7 12 V 3
Supply Current, Disabled ISS 0.25 4 µA Disabled 3
Supply Current, Operating ISS 0.75 4 mA Operating; VDD = VREG(Typ)+1V 3
UVLO Start Threshold (MCP73842, MCP73844) VSTART 8.45 8.65 8.9 V VDD Low-to-High 3
UVLO Stop Threshold (MCP73842, MCP73844) VSTOP 8.4 8.6 8.85 V VDD High-to-Low 3
Regulated Output Voltage (MCP73842-8.4, MCP73844-8.4) VREG 8.358 8.4 8.442 V VDD = [VREG(Typ)+1V], IOUT = 10 mA, TA = -5°C to +55°C 3
Line Regulation 0.025 0.25 %/V VDD = [VREG(Typ)+1V] to 12V, IOUT = 10 mA 3
Load Regulation 0.01 0.25 % IOUT = 10 mA to 150 mA, VDD = [VREG(Typ)+1V] 3
Output Reverse Leakage Current IDISCHARGE 0.4 1 µA VDD Floating, VBAT = VREG(Typ) 3
Fast Charge Current Regulation Threshold VFCS 100 110 120 mV VDD, VSENSE, TA = -5°C to +55°C 3
Precondition Current Regulation Threshold VPCS 5 10 15 mV VDD, VSENSE, TA = -5°C to +55°C 4
Precondition Threshold Voltage (MCP73842-8.4, MCP73844-8.4) VPTH 5.5 5.7 5.9 V VBAT Low-to-High 4
Charge Termination Threshold VTCS 4 7 10 mV VDD, VSENSE, TA = -5°C to +55°C 4
Gate Drive Minimum Voltage VDRVMIN 1 V VDD = 4.5V 4
Gate-Source Clamp Voltage VGS -7 -4.5 V VDD = 12.0V 4
Thermistor Reference Output Voltage VTHREF 2.475 2.55 2.625 V TA = +25°C, VDD = VREG(Typ)+1V, ITHREF = 0 mA 4
Thermistor Reference Source Current ITHREF 200 µA 4
Thermistor Reference Line Regulation 0.1 0.25 %/V VDD = [VREG(Typ)+1V] to 12V 4
Thermistor Reference Load Regulation 0.01 0.1 % ITHREF = 0 mA to 0.20 mA 4
Upper Trip Threshold VT1 1.18 1.25 1.32 V 4
Lower Trip Threshold VT2 0.59 0.62 0.66 V 4
Input Bias Current /IBIAS/ 2 µA 4
Status Sink Current ISINK 4 7 12 mA 4
Status Low Output Voltage VOL 200 400 mV ISINK = 1 mA 4
Status Input Leakage Current ILK 0.01 1 µA ISINK = 0 mA, VSTAT1 = 12V 4
Enable Input High-Voltage Level VIH 1.4 V 5
Enable Input Low-Voltage Level VIL 0.8 V 5
Enable Input Leakage Current ILK 0.01 1 µA VENABLE = 12V 5
UVLO Start Delay tSTART 5 msec VDD Low-to-High 5
Current Regulation Transition Time Out of Preconditioning tDELAY 1 msec VBAT < VPTH to VBAT > VPTH 5
Current Rise Time Out of Preconditioning tRISE 1 msec IOUT Rising to 90% of IREG 5
Fast Charge Safety Timer Period tFAST 1.1 1.5 1.9 Hours CTIMER = 0.1 µF 5
Preconditioning Charge Safety Timer Period tPRECON 45 60 75 Minutes CTIMER = 0.1 µF 5
Elapsed Time Termination Period tTERM 2.2 3 3.8 Hours CTIMER = 0.1 µF 5
Status Output turn-off tOFF 200 µsec ISINK = 10 mA to 0 mA 5
Status Output turn-on tON 200 µsec ISINK = 0 mA to 10 mA 5
Specified Temperature Range TA -40 85 °C 5
Operating Temperature Range TA -40 125 °C 5
Storage Temperature Range TA -65 150 °C 5
All inputs and outputs w.r.t. VSS -0.3 V w.r.t. VSS; upper limit printed as (VDD+0.3) V 3
Current at DRV Pin -4 4 mA 3
Current at STAT1 Pin -30 30 mA 3
Maximum Junction Temperature TJ 150 °C 3
ESD Human Body Model 2 kV Human Body Model (1.5 kΩ in series with 100 pF) 3
ESD Machine Model 200 V Machine Model (200 pF, no series resistance) 3
Thermal Resistance, MSOP-10 (junction to ambient) θJA 113 °C/W 4-Layer JC51-7 Standard Board, Natural Convection 5

CAD (KiCad official)

  • Symbol: MCP73842T-840I
  • Footprint: Package_SO:MSOP-10_3x3mm_P0.5mm
  • 3D model: MSOP-10 (KiCad packages3D, STEP)
  • 3D model files: mcp73842t-840i-etched.step / mcp73842t-840i-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp73842t-840i.step / mcp73842t-840i.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (26 pp, sha256 da2a0f52e1435a78, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF