← Commit history

Initial commit: component/mcp73833t-ami

Ray ·d8f9ce88d5 ·
2 files changed +84
README.mdadded+50
@@ -0,0 +1,50 @@+# MCP73833T-AMI++**Microchip** · Battery Management · DFN-10-EP(3x3)++MCP73833T-AMI from Microchip, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | VDD | power_in | Battery management input supply. Recommended supply of [VREG(typ) + 0.3 V] up to 6 V (absolute max 7.0 V). Bypass to VSS with a minimum of 1 uF. Pins 1 and 2 are internally tied together and both must be connected. |+| 2 | VDD | power_in | Battery management input supply (paralleled with pin 1). Both VDD pins must be connected to the input supply. |+| 3 | STAT1 | output | Charge status output 1. Open-drain output for LED (through a series resistor, typ. 470 ohm) or MCU logic input. Sink current 15 mA typ, 25 mA max; VOL <= 0.4 V at ISINK = 4 mA. Low during preconditioning / fast charge / constant voltage; Hi-Z in standby/shutdown/charge-complete. |+| 4 | STAT2 | output | Charge status output 2. Open-drain output for LED or MCU logic input. Combined with STAT1 and PG encodes the charger state per the state flow chart (e.g. STAT2 = LOW only in charge-complete). |+| 5 | VSS | power_in | Battery management 0 V reference. Connect to negative terminal of the battery and the input supply return. Exposed pad on DFN variant is internally tied to VSS. |+| 6 | PROG | input | Current regulation set and charge control enable. Program the fast-charge current via a resistor from PROG to VSS using IREG = 1000 V / RPROG (RPROG in kohm). Valid range 1 kohm to 20 kohm (100 mA to 1 A). Floating this pin (>200 kohm) disables the charger and enters standby. |+| 7 | PG | output | Power Good indication (MCP73833 variant). Pseudo open-drain output; can sink current but has an internal diode path back to VDD, so it must only be pulled up to VDD (not a higher rail). Asserted low whenever VDD is above UVLO and greater than VBAT. On the MCP73834 variant this pin is the Timer Enable (TE) input instead. |+| 8 | THERM | input | Thermistor input for cell temperature monitoring. Sources ~50 uA (47-53 uA) into an external NTC (nominally 10 kohm) tied to VSS. Comparators trip at VT1 = 1.23 V (upper, high temp) and VT2 = 0.25 V (lower, low temp) versus VTHERM. Tie to VSS through a resistor if unused (comparators disabled by pulling above (VDD-0.1 V) enters System Test / LDO mode). |+| 9 | VBAT | power_out | Battery charge control output (drain of the internal P-channel MOSFET pass device, RDSON ~300 mohm). Connect to the positive terminal of the Li-Ion/Li-Polymer cell. Pins 9 and 10 are internally paralleled and both must be connected. Bypass to VSS with a minimum of 1 uF for loop stability when the battery is disconnected. |+| 10 | VBAT | power_out | Battery charge control output (paralleled with pin 9). Both VBAT pins must be connected to the cell positive terminal. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | Microchip |+| Package | DFN-10-EP(3x3) |+| Category | PMIC |+| Pins | 10 |++## Ordering variants++- `MCP73833T-AMI`+- `MCP73833T-AMIMF`++## CAD (KiCad official)++- Symbol: `MCP73833T-AMI`+- Footprint: `Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm`+- 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [Microchip datasheet](docs/mcp73833t-ami-datasheet.pdf) (32 pp, sha256 `6b4bfb0f376ed244`, retrieved 2026-08-17, tier: manufacturer)+- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/mcp73833t-ami-datasheet.pdf)
page.jsonadded+34
@@ -0,0 +1,34 @@+{+  "slug": "mcp73833t-ami",+  "version": "0.1.0",+  "type": "component",+  "description": "Microchip Battery Management, DFN-10-EP(3x3). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "pmic",+    "mcp73833t-ami"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "mcp73833t-ami.kicad_sym",+    "mcp73833t-ami.kicad_mod",+    "mcp73833t-ami.glb",+    "mcp73833t-ami.step",+    "mcp73833t-ami.lbr",+    "docs/hero.png",+    "docs/mcp73833t-ami-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "visibility": "public",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file