← Commit history
README.md+73−37
@@ -1,39 +1,89 @@ # MCP73833T-AMI -**Microchip** · Battery Management · DFN-10-EP(3x3)+**Microchip Tech** · Battery Management · DFN-10-EP(3x3) -MCP73833T-AMI from Microchip, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.+MCP73833T-AMI from Microchip Tech, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.  ## Pinout  | Pin | Name | Type | Function | |---|---|---|---|-| 1 | VDD | power_in | Battery management input supply. Recommended supply of [VREG(typ) + 0.3 V] up to 6 V (absolute max 7.0 V). Bypass to VSS with a minimum of 1 uF. Pins 1 and 2 are internally tied together and both must be connected. |-| 2 | VDD | power_in | Battery management input supply (paralleled with pin 1). Both VDD pins must be connected to the input supply. |-| 3 | STAT1 | output | Charge status output 1. Open-drain output for LED (through a series resistor, typ. 470 ohm) or MCU logic input. Sink current 15 mA typ, 25 mA max; VOL <= 0.4 V at ISINK = 4 mA. Low during preconditioning / fast charge / constant voltage; Hi-Z in standby/shutdown/charge-complete. |-| 4 | STAT2 | output | Charge status output 2. Open-drain output for LED or MCU logic input. Combined with STAT1 and PG encodes the charger state per the state flow chart (e.g. STAT2 = LOW only in charge-complete). |-| 5 | VSS | power_in | Battery management 0 V reference. Connect to negative terminal of the battery and the input supply return. Exposed pad on DFN variant is internally tied to VSS. |-| 6 | PROG | input | Current regulation set and charge control enable. Program the fast-charge current via a resistor from PROG to VSS using IREG = 1000 V / RPROG (RPROG in kohm). Valid range 1 kohm to 20 kohm (100 mA to 1 A). Floating this pin (>200 kohm) disables the charger and enters standby. |-| 7 | PG | output | Power Good indication (MCP73833 variant). Pseudo open-drain output; can sink current but has an internal diode path back to VDD, so it must only be pulled up to VDD (not a higher rail). Asserted low whenever VDD is above UVLO and greater than VBAT. On the MCP73834 variant this pin is the Timer Enable (TE) input instead. |-| 8 | THERM | input | Thermistor input for cell temperature monitoring. Sources ~50 uA (47-53 uA) into an external NTC (nominally 10 kohm) tied to VSS. Comparators trip at VT1 = 1.23 V (upper, high temp) and VT2 = 0.25 V (lower, low temp) versus VTHERM. Tie to VSS through a resistor if unused (comparators disabled by pulling above (VDD-0.1 V) enters System Test / LDO mode). |-| 9 | VBAT | power_out | Battery charge control output (drain of the internal P-channel MOSFET pass device, RDSON ~300 mohm). Connect to the positive terminal of the Li-Ion/Li-Polymer cell. Pins 9 and 10 are internally paralleled and both must be connected. Bypass to VSS with a minimum of 1 uF for loop stability when the battery is disconnected. |-| 10 | VBAT | power_out | Battery charge control output (paralleled with pin 9). Both VBAT pins must be connected to the cell positive terminal. |+| 1 | VDD | power_in | Battery Management Input Supply. |+| 2 | VDD | power_in | Battery Management Input Supply. |+| 3 | STAT1 | output | Charge Status Output (open drain). |+| 4 | STAT2 | output | Charge Status Output (open drain). |+| 5 | VSS | power_in | Battery Management 0V Reference. |+| 6 | PROG | input | Current Regulation Set and Charge Control Enable. |+| 7 | PG | output | Power Good output (MCP73833). |+| 8 | THERM | input | Thermistor input. |+| 9 | VBAT | power_out | Battery Charge Control Output. |+| 10 | VBAT | power_out | Battery Charge Control Output. |+| 11 | EP | power_in | Exposed Thermal Pad (EP); must be connected to VSS. |  ## Key specifications  | Parameter | Value | |---|---|-| Manufacturer | Microchip |+| Manufacturer | Microchip Tech | | Package | DFN-10-EP(3x3) |-| Category | PMIC |-| Pins | 10 |--## Ordering variants--Same part, different packaging or reel option.--- `MCP73833T-AMI`-- `MCP73833T-AMIMF`+| Category | Power Management (PMIC) |+| Pins | 11 |++## Electrical characteristics++Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).++| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |+|---|---|---|---|---|---|---|---|+| Supply Voltage (absolute maximum) | VDD |  |  | 7 | V |  | 3 |+| All Inputs and Outputs w.r.t. VSS |  | -0.3 |  |  | V |  | 3 |+| Storage Temperature |  | -65 |  | 150 | °C |  | 3 |+| ESD protection, Human Body Model |  |  |  | 4 | kV | HBM (1.5 k in Series with 100 pF) | 3 |+| ESD protection, Machine Model |  |  |  | 300 | V | MM (200 pF, No Series Resistance) | 3 |+| Specified Temperature Range | TA | -40 |  | 85 | °C |  | 5 |+| Operating Temperature Range | TA | -40 |  | 125 | °C |  | 5 |+| Supply Voltage, Charging | VDD | 3.75 |  | 6 | V | Charging | 3 |+| Supply Voltage, Charge Complete / Standby | VDD |  |  | 6 | V | Charge Complete, Standby | 3 |+| Supply Current, Charging | ISS |  | 2000 | 3000 | µA | Charging | 3 |+| Supply Current, Charge Complete | ISS |  | 150 | 300 | µA | Charge Complete | 3 |+| Supply Current, Standby | ISS |  | 100 | 300 | µA | Standby (No Battery or PROG Floating) | 3 |+| Supply Current, Shutdown | ISS |  | 50 | 100 | µA | Shutdown (VDD < VBAT, or VDD < VSTOP) | 3 |+| UVLO Start Threshold | VSTART | 3.4 | 3.55 | 3.7 | V | VDD Low-to-High | 3 |+| UVLO Stop Threshold | VSTOP | 3.3 | 3.45 | 3.6 | V | VDD High-to-Low | 3 |+| Regulated Output Voltage (4.20V option) | VREG | 4.168 | 4.2 | 4.232 | V | VDD = [VREG(Typical) + 1V], IOUT = 10 mA, TA = −5°C to +55°C | 3 |+| Line Regulation |  |  | 0.1 | 0.3 | %/V | VDD = [VREG(Typical)+1V] to 6V, IOUT = 10 mA | 3 |+| Load Regulation |  |  | 0.1 | 0.3 | % | IOUT = 10 mA to 100 mA, VDD = [VREG(Typical)+1V] | 3 |+| Fast Charge Current Regulation (PROG = 10 k) | IREG | 90 | 100 | 110 | mA | PROG = 10 k, TA = −5°C to +55°C | 3 |+| Fast Charge Current Regulation (PROG = 1.0 k) | IREG | 900 | 1000 | 1100 | mA | PROG = 1.0 k, TA = −5°C to +55°C | 3 |+| Precondition Current Ratio (10% option) | IPREG / IREG | 7.5 | 10 | 12.5 | % | PROG = 1.0 k to 10 k | 4 |+| Precondition Voltage Threshold Ratio (71.5% option) | VPTH / VREG | 69 | 71.5 | 75 | % |  | 4 |+| Charge Termination Current Ratio (7.5% option) | ITERM / IREG | 5.6 | 7.5 | 9.4 | % | TA = −5°C to +55°C | 4 |+| Output Reverse Leakage Current, PROG floating | IDISCHARGE |  | 0.15 | 2 | µA | PROG Floating | 4 |+| Output Reverse Leakage Current, VDD < VBAT | IDISCHARGE |  | 0.25 | 2 | µA | VDD < VBAT | 4 |+| Output Reverse Leakage Current, VDD < VSTOP | IDISCHARGE |  | 0.15 | 2 | µA | VDD < VSTOP | 4 |+| Output Reverse Leakage Current, Charge Complete | IDISCHARGE |  | -5.5 | -15 | µA | Charge Complete | 4 |+| Sink Current (STAT1, STAT2, PG) | ISINK |  | 15 | 25 | mA |  | 4 |+| Low Output Voltage (STAT1, STAT2, PG) | VOL |  | 0.4 | 1 | V | ISINK = 4 mA | 4 |+| Input Leakage Current (status outputs) | ILK |  | 0.01 | 1 | µA | High Impedance, 6V on pin | 4 |+| Charge Impedance Range | RPROG | 1 |  | 20 | kΩ |  | 4 |+| Standby Impedance | RPROG | 70 |  | 200 | kΩ | Minimum Impedance for Standby | 4 |+| Thermistor Current Source | ITHERM | 47 | 50 | 53 | µA | 2 k < RTHERM < 50 k | 4 |+| Upper Trip Threshold | VT1 | 1.2 | 1.23 | 1.26 | V | VTHERM Low-to-High | 4 |+| Lower Trip Threshold | VT2 | 0.235 | 0.25 | 0.265 | V | VTHERM High-to-Low | 4 |+| THERM Input Sink Current | ISINK | 3 | 6 | 20 | µA | Stand-by or system test mode | 4 |+| Bypass Capacitance (IOUT < 250 mA) | CBAT | 1 |  |  | µF | IOUT < 250 mA | 4 |+| Bypass Capacitance (IOUT > 250 mA) | CBAT | 4.7 |  |  | µF | IOUT > 250 mA | 4 |+| UVLO Start Delay | tSTART |  |  | 5 | ms | VDD Low-to-High | 5 |+| Transition Time Out of Preconditioning | tDELAY |  |  | 1 | ms | VBAT<VPTH to VBAT>VPTH | 5 |+| Current Rise Time Out of Preconditioning | tRISE |  |  | 1 | ms | IOUT Rising to 90% of IREG | 5 |+| Preconditioning Comparator Filter Time | tPRECON | 0.4 | 1.3 | 3.2 | ms | Average VBAT Rise/Fall | 5 |+| Termination Comparator Filter Time | tTERM | 0.4 | 1.3 | 3.2 | ms | Average IOUT Falling | 5 |+| Charge Comparator Filter Time | tCHARGE | 0.4 | 1.3 | 3.2 | ms | Average VBAT Falling | 5 |+| Thermistor Comparator Filter Time | tTHERM | 0.4 | 1.3 | 3.2 | ms | Average THERM Rise/Fall | 5 |+| Elapsed Timer Period (0 hours option) | tELAPSED | 0 | 0 | 0 | Hours | Timer Disabled | 5 |+| Status Output turn-off time | tOFF |  |  | 200 | µs | ISINK = 1 mA to 0 mA | 5 |+| Status Output turn-on time | tON |  |  | 200 | µs | ISINK = 0 mA to 1 mA | 5 |+| Thermal Resistance, DFN-10 3x3 | JA |  | 41 |  | °C/W | 4-Layer JC51-7 Standard Board, Natural Convection | 5 |  ## CAD (KiCad official) @@ -42,25 +92,11 @@ Same part, different packaging or reel option. - 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP) - 3D model files: `mcp73833t-ami-etched.step` / `mcp73833t-ami-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mcp73833t-ami.step` / `mcp73833t-ami.glb` are the bare package body. -## 3D model downloads--Two STEP files. Same geometry, different body top:--| File | Size | Use it when |-|---|---|---|-| [`mcp73833t-ami.step`](mcp73833t-ami.step) | 126 KB | You want the bare part, or you mark your own boards. |-| [`mcp73833t-ami-etched.step`](mcp73833t-ami-etched.step) | 2.3 MB | You want the part with `MCP73833T-AMI` already on it. |--The marking in the etched file is real recessed geometry cut into the solid, not a-texture or a decal: 559 faces against 74 in the bare model. It-survives export, section views, and rendering in any CAD tool, and it drops straight-into KiCad or Fusion with no extra setup.- ## Provenance  Data extracted from the manufacturer datasheet, not a distributor listing: -- **Datasheet:** [Microchip datasheet](docs/mcp73833t-ami-datasheet.pdf) (32 pp, sha256 `6b4bfb0f376ed244`, retrieved 2026-08-17, tier: manufacturer)+- **Datasheet:** [Microchip Tech datasheet](https://ww1.microchip.com/downloads/aemDocuments/documents/APID/ProductDocuments/DataSheets/MCP73833-4-Stand-Alone-Linear-Li-Ion-Li-Polymer-Charge-Management-Controller-DS20002005.pdf) (29 pp, sha256 `814b6082bd5076db`, retrieved 2026-11-12, tier: manufacturer) - **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - **CAD:** KiCad official libraries (CC-BY-SA 4.0). 
docs/hero.png
⋯ 1 unchanged line ⋯
docs/mcp73833t-ami-datasheet.pdf
⋯ 1 unchanged line ⋯
mcp73833t-ami-hero.glbadded
⋯ 1 unchanged line ⋯
mcp73833t-ami-hero.overlay.jsonadded+317
@@ -0,0 +1,317 @@+{+  "spec": "adom-hero 1.4",+  "mpn": "MCP73833T-AMI/MF",+  "kind": "component + footprint reference art",+  "board_use": false,+  "plane_z_mm": -0.02,+  "units": "metre",+  "upAxis": "Z",+  "layers": {+    "pad_outlines": {+      "material": "Footprint pads - teal dashed outlines - 50 percent opacity",+      "rgba": [+        0.0,+        0.902,+        0.863,+        0.5+      ],+      "pads": 11,+      "span_mm": 4.65,+      "dash_mm": 0.12,+      "gap_mm": 0.072,+      "pad_stroke_mm": 0.03+    },+    "silkscreen": {+      "material": "Silkscreen reference lines - 30 percent opacity",+      "rgba": [+        0.92,+        0.96,+        1.0,+        0.3+      ],+      "footprint_items": 3,+      "pin1": {+        "source": "footprint silkscreen",+        "pad": "1"+      }+    },+    "signal_names": {+      "material": "Signal names - 50 percent opacity",+      "rgba": [+        0.92,+        0.96,+        1.0,+        0.5+      ],+      "font": "DejaVu Sans Mono",+      "labels": 10,+      "sides": "top + mirrored underside (single-sided)",+      "fallback_to_pad_number": 0+    }+  },+  "align": {+    "ok": true,+    "centre_offset_mm": 0.0,+    "tolerance_mm": 0.3,+    "orientation_flipped": false,+    "contacts_bbox_mm": [+      -1.5,+      1.5,+      -1.49,+      1.49+    ],+    "pads_bbox_mm": [+      -1.875,+      1.875,+      -1.24,+      1.24+    ],+    "seating_z_mm": 0.0+  },+  "sources": {+    "glb": "mcp73833t-ami-etched.glb",+    "glb_sha256": "fe6fd639cd0440cfadf4578d21f1ececd38b2348bfa90cfc4814b67f112dd99e",+    "footprint": "mcp73833t-ami.kicad_mod",+    "footprint_sha256": "482a9deb87a5cf274e57d764e9bbb1e28b280ff74f59e181125c7cf9c369d1a4",+    "pins": "page.json component.pins",+    "pins_sha256": "fe1a31a65cbd1937628a786fd039f496f01e51a50960e13cb03a3d249322306c"+  },+  "generator": "adom-wiki 1.8.23 (component_hero)",+  "labels": [+    {+      "pad": "1",+      "text": "VDD",+      "x": -1.975,+      "y": -1.0,+      "align": "right",+      "vertical": false,+      "h": 0.25+    },+    {+      "pad": "2",+      "text": "VDD",+      "x": -1.975,+      "y": -0.5,+      "align": "right",+      "vertical": false,+      "h": 0.25+    },+    {+      "pad": "3",+      "text": "STAT1",+      "x": -1.975,+      "y": 0.0,+      "align": "right",+      "vertical": false,+      "h": 0.25+    },+    {+      "pad": "4",+      "text": "STAT2",+      "x": -1.975,+      "y": 0.5,+      "align": "right",+      "vertical": false,+      "h": 0.25+    },+    {+      "pad": "5",+      "text": "VSS",+      "x": -1.975,+      "y": 1.0,+      "align": "right",+      "vertical": false,+      "h": 0.25+    },+    {+      "pad": "6",+      "text": "PROG",+      "x": 1.975,+      "y": 1.0,+      "align": "left",+      "vertical": false,+      "h": 0.25+    },+    {+      "pad": "7",+      "text": "PG",+      "x": 1.975,+      "y": 0.5,+      "align": "left",+      "vertical": false,+      "h": 0.25+    },+    {+      "pad": "8",+      "text": "THERM",+      "x": 1.975,+      "y": 0.0,+      "align": "left",+      "vertical": false,+      "h": 0.25+    },+    {+      "pad": "9",+      "text": "VBAT",+      "x": 1.975,+      "y": -0.5,+      "align": "left",+      "vertical": false,+      "h": 0.25+    },+    {+      "pad": "10",+      "text": "VBAT",+      "x": 1.975,+      "y": -1.0,+      "align": "left",+      "vertical": false,+      "h": 0.25+    }+  ],+  "pads": [+    {+      "number": "1",+      "shape": "rect",+      "center_mm": [+        -1.55,+        -1.0+      ],+      "size_mm": [+        0.65,+        0.3+      ],+      "rot": 0.0+    },+    {+      "number": "2",+      "shape": "rect",+      "center_mm": [+        -1.55,+        -0.5+      ],+      "size_mm": [+        0.65,+        0.3+      ],+      "rot": 0.0+    },+    {+      "number": "3",+      "shape": "rect",+      "center_mm": [+        -1.55,+        0.0+      ],+      "size_mm": [+        0.65,+        0.3+      ],+      "rot": 0.0+    },+    {+      "number": "4",+      "shape": "rect",+      "center_mm": [+        -1.55,+        0.5+      ],+      "size_mm": [+        0.65,+        0.3+      ],+      "rot": 0.0+    },+    {+      "number": "5",+      "shape": "rect",+      "center_mm": [+        -1.55,+        1.0+      ],+      "size_mm": [+        0.65,+        0.3+      ],+      "rot": 0.0+    },+    {+      "number": "6",+      "shape": "rect",+      "center_mm": [+        1.55,+        1.0+      ],+      "size_mm": [+        0.65,+        0.3+      ],+      "rot": 0.0+    },+    {+      "number": "7",+      "shape": "rect",+      "center_mm": [+        1.55,+        0.5+      ],+      "size_mm": [+        0.65,+        0.3+      ],+      "rot": 0.0+    },+    {+      "number": "8",+      "shape": "rect",+      "center_mm": [+        1.55,+        0.0+      ],+      "size_mm": [+        0.65,+        0.3+      ],+      "rot": 0.0+    },+    {+      "number": "9",+      "shape": "rect",+      "center_mm": [+        1.55,+        -0.5+      ],+      "size_mm": [+        0.65,+        0.3+      ],+      "rot": 0.0+    },+    {+      "number": "10",+      "shape": "rect",+      "center_mm": [+        1.55,+        -1.0+      ],+      "size_mm": [+        0.65,+        0.3+      ],+      "rot": 0.0+    },+    {+      "number": "11",+      "shape": "rect",+      "center_mm": [+        0.0,+        0.0+      ],+      "size_mm": [+        1.55,+        2.48+      ],+      "rot": 0.0+    }+  ]+}
mcp73833t-ami.kicad_mod+7−41
@@ -27,7 +27,7 @@ 			) 		) 	)-	(property "Datasheet" ""+	(property "Datasheet" "https://ww1.microchip.com/downloads/aemDocuments/documents/APID/ProductDocuments/DataSheets/MCP73833-4-Stand-Alone-Linear-Li-Ion-Li-Polymer-Charge-Management-Controller-DS20002005.pdf" 		(at 0 0 0) 		(unlocked yes) 		(layer "F.Fab")@@ -87,46 +87,6 @@ 		(layer "F.SilkS") 		(uuid "0a8887b8-2717-4558-80a2-8fb70933ffab") 	)-	(fp_line-		(start -2.15 -1.85)-		(end -2.15 1.85)-		(stroke-			(width 0.05)-			(type solid)-		)-		(layer "F.CrtYd")-		(uuid "21ddb6bb-762e-4b45-863e-03b69486bb25")-	)-	(fp_line-		(start -2.15 -1.85)-		(end 2.15 -1.85)-		(stroke-			(width 0.05)-			(type solid)-		)-		(layer "F.CrtYd")-		(uuid "a1a9fbc7-3f1b-4aef-b384-68edb4ffe8c7")-	)-	(fp_line-		(start -2.15 1.85)-		(end 2.15 1.85)-		(stroke-			(width 0.05)-			(type solid)-		)-		(layer "F.CrtYd")-		(uuid "e6496e6f-2e80-45d0-9bea-b4d5495b1ede")-	)-	(fp_line-		(start 2.15 -1.85)-		(end 2.15 1.85)-		(stroke-			(width 0.05)-			(type solid)-		)-		(layer "F.CrtYd")-		(uuid "fdccb8f2-4751-4581-8fbc-d78ff35ff4b7")-	) 	(fp_line 		(start -1.5 -0.75) 		(end -0.75 -1.5)@@ -290,4 +250,10 @@ 			(xyz 0 0 0) 		) 	)+	(fp_poly+		(pts (xy -2.13 -1.49) (xy -1.75 -1.49) (xy -1.75 -1.75) (xy 1.75 -1.75) (xy 1.75 -1.49) (xy 2.13 -1.49) (xy 2.13 1.49) (xy 1.75 1.49) (xy 1.75 1.75) (xy -1.75 1.75) (xy -1.75 1.49) (xy -2.13 1.49))+		(stroke (width 0.05) (type solid))+		(fill no)+		(layer "F.CrtYd")+	) )
mcp73833t-ami.kicad_sym+14−10
@@ -1,10 +1,10 @@ (kicad_symbol_lib (version 20211014) (generator ds2sf_rect)   (symbol "MCP73833T-AMI" (in_bom yes) (on_board yes)     (property "Reference" "U" (at 0 10.16 0) (effects (font (size 1.27 1.27))))-    (property "Value" "MCP73833T-AMI" (at 0 -10.16 0) (effects (font (size 1.27 1.27))))+    (property "Value" "MCP73833T-AMI" (at 0 -12.70 0) (effects (font (size 1.27 1.27))))     (property "Footprint" "" (at 0 0 0) (effects (font (size 1.27 1.27)) hide))     (symbol "MCP73833T-AMI_0_1"-    (rectangle (start -12.70 7.62) (end 12.70 -7.62)+    (rectangle (start -12.70 7.62) (end 12.70 -10.16)       (stroke (width 0.254) (type default)) (fill (type background)))     )     (symbol "MCP73833T-AMI_1_1"@@ -28,26 +28,30 @@       (name "VSS" (effects (font (size 1.27 1.27))))       (number "5" (effects (font (size 1.27 1.27))))     )-    (pin power_out line (at 17.78 5.08 180) (length 5.08)+    (pin input line (at -17.78 -7.62 0) (length 5.08)+      (name "PROG" (effects (font (size 1.27 1.27))))+      (number "6" (effects (font (size 1.27 1.27))))+    )+    (pin power_in line (at 17.78 5.08 180) (length 5.08)+      (name "EP" (effects (font (size 1.27 1.27))))+      (number "11" (effects (font (size 1.27 1.27))))+    )+    (pin power_out line (at 17.78 2.54 180) (length 5.08)       (name "VBAT" (effects (font (size 1.27 1.27))))       (number "10" (effects (font (size 1.27 1.27))))     )-    (pin power_out line (at 17.78 2.54 180) (length 5.08)+    (pin power_out line (at 17.78 0.00 180) (length 5.08)       (name "VBAT" (effects (font (size 1.27 1.27))))       (number "9" (effects (font (size 1.27 1.27))))     )-    (pin input line (at 17.78 0.00 180) (length 5.08)+    (pin input line (at 17.78 -2.54 180) (length 5.08)       (name "THERM" (effects (font (size 1.27 1.27))))       (number "8" (effects (font (size 1.27 1.27))))     )-    (pin output line (at 17.78 -2.54 180) (length 5.08)+    (pin output line (at 17.78 -5.08 180) (length 5.08)       (name "PG" (effects (font (size 1.27 1.27))))       (number "7" (effects (font (size 1.27 1.27))))     )-    (pin input line (at 17.78 -5.08 180) (length 5.08)-      (name "PROG" (effects (font (size 1.27 1.27))))-      (number "6" (effects (font (size 1.27 1.27))))-    )     )   ) )
mcp73833t-ami.lbr+27−14
@@ -50,7 +50,7 @@ <layer number="98" name="Guide" color="6" fill="1" visible="yes" active="yes"/> </layers> <library>-<description></description>+<description>Microchip Tech Battery Management, DFN-10-EP(3x3). Pinout settled in review by an AI reviewer against the manufacturer&apos;s datasheet</description> <packages> <package name="DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm">   <description>DFN-10-1EP, 3 x 3 mm, 0.5 mm pitch. 10-Lead Plastic Dual Flat, No Lead Package (MF) - 3x3x0.9 mm Body [DFN] (see Microchip Packaging Specification 00000049BS.pdf)</description>@@ -64,7 +64,7 @@   <smd name="8" x="1.5500" y="-0.0000" dx="0.6500" dy="0.3000" layer="1"/>   <smd name="9" x="1.5500" y="0.5000" dx="0.6500" dy="0.3000" layer="1"/>   <smd name="10" x="1.5500" y="1.0000" dx="0.6500" dy="0.3000" layer="1"/>-  <smd name="11" x="0.0000" y="-0.0000" dx="1.5500" dy="2.4800" layer="1"/>+  <smd name="11" x="0.0000" y="-0.0000" dx="1.5500" dy="2.4800" layer="1" cream="no"/>   <polygon width="0.1200" layer="21">     <vertex x="-2.0600" y="1.3400"/>     <vertex x="-2.5400" y="1.3400"/>@@ -84,27 +84,29 @@ </packages> <symbols> <symbol name="MCP73833T-AMI">+  <description>Microchip Tech Battery Management, DFN-10-EP(3x3). Pinout settled in review by an AI reviewer against the manufacturer&apos;s datasheet</description>   <wire x1="-12.7" y1="7.62" x2="12.7" y2="7.62" width="0.254" layer="94"/>-  <wire x1="12.7" y1="7.62" x2="12.7" y2="-7.62" width="0.254" layer="94"/>-  <wire x1="12.7" y1="-7.62" x2="-12.7" y2="-7.62" width="0.254" layer="94"/>-  <wire x1="-12.7" y1="-7.62" x2="-12.7" y2="7.62" width="0.254" layer="94"/>+  <wire x1="12.7" y1="7.62" x2="12.7" y2="-10.16" width="0.254" layer="94"/>+  <wire x1="12.7" y1="-10.16" x2="-12.7" y2="-10.16" width="0.254" layer="94"/>+  <wire x1="-12.7" y1="-10.16" x2="-12.7" y2="7.62" width="0.254" layer="94"/>   <text x="0.0000" y="10.1600" size="1.27" layer="95" align="center">&gt;NAME</text>-  <text x="0.0000" y="-10.1600" size="1.27" layer="96" align="center">&gt;VALUE</text>+  <text x="0.0000" y="-12.7000" size="1.27" layer="96" align="center">&gt;VALUE</text>   <pin name="VDD" x="-17.78" y="5.08" length="middle" direction="pwr"/>   <pin name="VDD@2" x="-17.78" y="2.54" length="middle" direction="pwr"/>   <pin name="STAT1" x="-17.78" y="0" length="middle" direction="out"/>   <pin name="STAT2" x="-17.78" y="-2.54" length="middle" direction="out"/>   <pin name="VSS" x="-17.78" y="-5.08" length="middle" direction="pwr"/>-  <pin name="VBAT" x="17.78" y="5.08" length="middle" direction="out" rot="R180"/>-  <pin name="VBAT@2" x="17.78" y="2.54" length="middle" direction="out" rot="R180"/>-  <pin name="THERM" x="17.78" y="0" length="middle" direction="in" rot="R180"/>-  <pin name="PG" x="17.78" y="-2.54" length="middle" direction="out" rot="R180"/>-  <pin name="PROG" x="17.78" y="-5.08" length="middle" direction="in" rot="R180"/>+  <pin name="PROG" x="-17.78" y="-7.62" length="middle" direction="in"/>+  <pin name="EP" x="17.78" y="5.08" length="middle" direction="pwr" rot="R180"/>+  <pin name="VBAT" x="17.78" y="2.54" length="middle" direction="out" rot="R180"/>+  <pin name="VBAT@2" x="17.78" y="0" length="middle" direction="out" rot="R180"/>+  <pin name="THERM" x="17.78" y="-2.54" length="middle" direction="in" rot="R180"/>+  <pin name="PG" x="17.78" y="-5.08" length="middle" direction="out" rot="R180"/> </symbol> </symbols> <devicesets> <deviceset name="MCP73833T-AMI" prefix="U">-  <description></description>+  <description>Microchip Tech Battery Management, DFN-10-EP(3x3). Pinout settled in review by an AI reviewer against the manufacturer&apos;s datasheet</description>   <gates>     <gate name="G$1" symbol="MCP73833T-AMI" x="0" y="0"/>   </gates>@@ -116,13 +118,24 @@         <connect gate="G$1" pin="STAT1" pad="3"/>         <connect gate="G$1" pin="STAT2" pad="4"/>         <connect gate="G$1" pin="VSS" pad="5"/>+        <connect gate="G$1" pin="PROG" pad="6"/>+        <connect gate="G$1" pin="EP" pad="11"/>         <connect gate="G$1" pin="VBAT" pad="10"/>         <connect gate="G$1" pin="VBAT@2" pad="9"/>         <connect gate="G$1" pin="THERM" pad="8"/>         <connect gate="G$1" pin="PG" pad="7"/>-        <connect gate="G$1" pin="PROG" pad="6"/>       </connects>-      <technologies><technology name=""/></technologies>+      <technologies>+        <technology name="">+          <attribute name="MPN" value="MCP73833T-AMI/MF" constant="no"/>+          <attribute name="MANUFACTURER" value="Microchip Tech" constant="no"/>+          <attribute name="DATASHEET" value="https://ww1.microchip.com/downloads/aemDocuments/documents/APID/ProductDocuments/DataSheets/MCP73833-4-Stand-Alone-Linear-Li-Ion-Li-Polymer-Charge-Management-Controller-DS20002005.pdf" constant="no"/>+          <attribute name="ADOM_WIKI" value="https://wiki.adom.inc/adom/mcp73833t-ami" constant="no"/>+          <attribute name="MOUSER_PN" value="579-MCP73833T-AMI/MF" constant="no"/>+          <attribute name="DIGIKEY_PN" value="MCP73833T-AMI/MFTR-ND" constant="no"/>+          <attribute name="LCSC_PN" value="C340160" constant="no"/>+        </technology>+      </technologies>     </device>   </devices> </deviceset>
package.json+175−7
@@ -1,12 +1,14 @@ {   "slug": "mcp73833t-ami",-  "version": "0.2.0",+  "version": "0.2.1",   "type": "component",-  "description": "Microchip Battery Management, DFN-10-EP(3x3). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "description": "Microchip Tech Battery Management, DFN-10-EP(3x3). Pinout settled in review by an AI reviewer against the manufacturer's datasheet, KiCad symbol/footprint/3D.",   "tags": [     "component",-    "pmic",-    "mcp73833t-ami"+    "power management (pmic)",+    "mcp73833t-ami",+    "factory-2.0.0",+    "extractor-text"   ],   "dependencies": {},   "hero": {@@ -24,6 +26,172 @@     "docs/hero.png",     "docs/mcp73833t-ami-datasheet.pdf",     "viewers/symbol.html",-    "viewers/footprint.html"-  ]-}\ No newline at end of file+    "viewers/footprint.html",+    "mcp73833t-ami-hero.glb",+    "mcp73833t-ami-hero.overlay.json"+  ],+  "component": {+    "mpn": "MCP73833T-AMI/MF",+    "manufacturer": "Microchip Tech",+    "package": "DFN-10-EP(3x3)",+    "pin_count": 11,+    "category": "Power Management (PMIC)",+    "subcategory": "Battery Management",+    "datasheet": "https://ww1.microchip.com/downloads/aemDocuments/documents/APID/ProductDocuments/DataSheets/MCP73833-4-Stand-Alone-Linear-Li-Ion-Li-Polymer-Charge-Management-Controller-DS20002005.pdf",+    "parts": {+      "symbol": "mcp73833t-ami.kicad_sym",+      "footprint": "mcp73833t-ami.kicad_mod",+      "model_3d": "mcp73833t-ami-hero.glb",+      "model_3d_plain": "mcp73833t-ami.glb",+      "model_3d_step": "mcp73833t-ami-etched.step",+      "model_3d_step_plain": "mcp73833t-ami.step",+      "lbr": "mcp73833t-ami.lbr"+    },+    "distributor_links": {+      "lcsc": "C340160",+      "digikey": "MCP73833T-AMI/MFTR-ND",+      "mouser": "579-MCP73833T-AMI/MF"+    },+    "distributor_check": {+      "checked_at": "2026-11-12T21:10:27Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "MCP73833T-AMI/MFTR-ND",+        "status": "found"+      },+      "mouser": {+        "pn": "579-MCP73833T-AMI/MF",+        "status": "found"+      },+      "matched_as": "MCP73833T-AMI/MF"+    },+    "pins": [+      {+        "number": "1",+        "name": "VDD",+        "type": "power_in",+        "description": "Battery Management Input Supply."+      },+      {+        "number": "2",+        "name": "VDD",+        "type": "power_in",+        "description": "Battery Management Input Supply."+      },+      {+        "number": "3",+        "name": "STAT1",+        "type": "output",+        "description": "Charge Status Output (open drain)."+      },+      {+        "number": "4",+        "name": "STAT2",+        "type": "output",+        "description": "Charge Status Output (open drain)."+      },+      {+        "number": "5",+        "name": "VSS",+        "type": "power_in",+        "description": "Battery Management 0V Reference."+      },+      {+        "number": "6",+        "name": "PROG",+        "type": "input",+        "description": "Current Regulation Set and Charge Control Enable."+      },+      {+        "number": "7",+        "name": "PG",+        "type": "output",+        "description": "Power Good output (MCP73833)."+      },+      {+        "number": "8",+        "name": "THERM",+        "type": "input",+        "description": "Thermistor input."+      },+      {+        "number": "9",+        "name": "VBAT",+        "type": "power_out",+        "description": "Battery Charge Control Output."+      },+      {+        "number": "10",+        "name": "VBAT",+        "type": "power_out",+        "description": "Battery Charge Control Output."+      },+      {+        "number": "11",+        "name": "EP",+        "type": "power_in",+        "description": "Exposed Thermal Pad (EP); must be connected to VSS."+      }+    ],+    "provenance": {+      "extractor": "ds2sf",+      "datasheet": {+        "url": "https://ww1.microchip.com/downloads/aemDocuments/documents/APID/ProductDocuments/DataSheets/MCP73833-4-Stand-Alone-Linear-Li-Ion-Li-Polymer-Charge-Management-Controller-DS20002005.pdf",+        "pages": 29,+        "sha256": "814b6082bd5076db",+        "source_tier": "mfr"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 11,+        "described": 11,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    },+    "models_3d": [+      {+        "file": "mcp73833t-ami.step",+        "role": "plain",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          3.0,+          2.98,+          0.77+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "738e2eb45860c11759f8e4f44ab26932b7c15e4d5d6c8c9ac22ae866a3e38711",+        "checked": "2026-11-12",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      },+      {+        "file": "mcp73833t-ami-etched.step",+        "role": "eda",+        "up": "Z",+        "units": "mm",+        "origin": "footprint origin = pad-pattern centre",+        "seat": "z = 0",+        "extents_mm": [+          3.0,+          2.98,+          0.77+        ],+        "zmin_mm": 0.0,+        "centre_offset_mm": 0.0,+        "footprint_binding": "identity",+        "sha256": "eb6035fd8ca1f8552be90a9d7f53bee1af731c8a7db09e4553b8436de34a0847",+        "checked": "2026-11-12",+        "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"+      }+    ]+  }+}
page.json+66−38
@@ -4,105 +4,130 @@   "slug": "mcp73833t-ami",   "title": "MCP73833T-AMI",   "brief": "Microchip Battery Management, DFN-10-EP(3x3). Pinout extracted from the datasheet, KiCad symbol/footprint/3D.",-  "version": "0.2.0",+  "version": "0.2.1",   "license": "CC-BY-SA-4.0",   "tags": [     "component",-    "pmic",-    "mcp73833t-ami"+    "power management (pmic)",+    "mcp73833t-ami",+    "factory-2.0.0",+    "extractor-text"   ],   "component": {-    "mpn": "MCP73833T-AMI",-    "manufacturer": "Microchip",+    "mpn": "MCP73833T-AMI/MF",+    "manufacturer": "Microchip Tech",     "package": "DFN-10-EP(3x3)",-    "pin_count": 10,-    "category": "PMIC",+    "pin_count": 11,+    "category": "Power Management (PMIC)",     "subcategory": "Battery Management",-    "datasheet": "https://datasheet.lcsc.com/datasheet/pdf/3ecd7c892c8368fd4dd78f900871fdca.pdf",+    "datasheet": "https://ww1.microchip.com/downloads/aemDocuments/documents/APID/ProductDocuments/DataSheets/MCP73833-4-Stand-Alone-Linear-Li-Ion-Li-Polymer-Charge-Management-Controller-DS20002005.pdf",     "parts": {       "symbol": "mcp73833t-ami.kicad_sym",       "footprint": "mcp73833t-ami.kicad_mod",-      "model_3d": "mcp73833t-ami-etched.glb",+      "model_3d": "mcp73833t-ami-hero.glb",       "model_3d_plain": "mcp73833t-ami.glb",       "model_3d_step": "mcp73833t-ami-etched.step",       "model_3d_step_plain": "mcp73833t-ami.step",       "lbr": "mcp73833t-ami.lbr"     },-    "distributor_links": {},+    "distributor_links": {+      "lcsc": "C340160",+      "digikey": "MCP73833T-AMI/MFTR-ND",+      "mouser": "579-MCP73833T-AMI/MF"+    },+    "distributor_check": {+      "checked_at": "2026-11-12T21:10:27Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "MCP73833T-AMI/MFTR-ND",+        "status": "found"+      },+      "mouser": {+        "pn": "579-MCP73833T-AMI/MF",+        "status": "found"+      },+      "matched_as": "MCP73833T-AMI/MF"+    },     "pins": [       {         "number": "1",         "name": "VDD",         "type": "power_in",-        "description": "Battery management input supply. Recommended supply of [VREG(typ) + 0.3 V] up to 6 V (absolute max 7.0 V). Bypass to VSS with a minimum of 1 uF. Pins 1 and 2 are internally tied together and both must be connected."+        "description": "Battery Management Input Supply."       },       {         "number": "2",         "name": "VDD",         "type": "power_in",-        "description": "Battery management input supply (paralleled with pin 1). Both VDD pins must be connected to the input supply."+        "description": "Battery Management Input Supply."       },       {         "number": "3",         "name": "STAT1",         "type": "output",-        "description": "Charge status output 1. Open-drain output for LED (through a series resistor, typ. 470 ohm) or MCU logic input. Sink current 15 mA typ, 25 mA max; VOL <= 0.4 V at ISINK = 4 mA. Low during preconditioning / fast charge / constant voltage; Hi-Z in standby/shutdown/charge-complete."+        "description": "Charge Status Output (open drain)."       },       {         "number": "4",         "name": "STAT2",         "type": "output",-        "description": "Charge status output 2. Open-drain output for LED or MCU logic input. Combined with STAT1 and PG encodes the charger state per the state flow chart (e.g. STAT2 = LOW only in charge-complete)."+        "description": "Charge Status Output (open drain)."       },       {         "number": "5",         "name": "VSS",         "type": "power_in",-        "description": "Battery management 0 V reference. Connect to negative terminal of the battery and the input supply return. Exposed pad on DFN variant is internally tied to VSS."+        "description": "Battery Management 0V Reference."       },       {         "number": "6",         "name": "PROG",         "type": "input",-        "description": "Current regulation set and charge control enable. Program the fast-charge current via a resistor from PROG to VSS using IREG = 1000 V / RPROG (RPROG in kohm). Valid range 1 kohm to 20 kohm (100 mA to 1 A). Floating this pin (>200 kohm) disables the charger and enters standby."+        "description": "Current Regulation Set and Charge Control Enable."       },       {         "number": "7",         "name": "PG",         "type": "output",-        "description": "Power Good indication (MCP73833 variant). Pseudo open-drain output; can sink current but has an internal diode path back to VDD, so it must only be pulled up to VDD (not a higher rail). Asserted low whenever VDD is above UVLO and greater than VBAT. On the MCP73834 variant this pin is the Timer Enable (TE) input instead."+        "description": "Power Good output (MCP73833)."       },       {         "number": "8",         "name": "THERM",         "type": "input",-        "description": "Thermistor input for cell temperature monitoring. Sources ~50 uA (47-53 uA) into an external NTC (nominally 10 kohm) tied to VSS. Comparators trip at VT1 = 1.23 V (upper, high temp) and VT2 = 0.25 V (lower, low temp) versus VTHERM. Tie to VSS through a resistor if unused (comparators disabled by pulling above (VDD-0.1 V) enters System Test / LDO mode)."+        "description": "Thermistor input."       },       {         "number": "9",         "name": "VBAT",         "type": "power_out",-        "description": "Battery charge control output (drain of the internal P-channel MOSFET pass device, RDSON ~300 mohm). Connect to the positive terminal of the Li-Ion/Li-Polymer cell. Pins 9 and 10 are internally paralleled and both must be connected. Bypass to VSS with a minimum of 1 uF for loop stability when the battery is disconnected."+        "description": "Battery Charge Control Output."       },       {         "number": "10",         "name": "VBAT",         "type": "power_out",-        "description": "Battery charge control output (paralleled with pin 9). Both VBAT pins must be connected to the cell positive terminal."+        "description": "Battery Charge Control Output."+      },+      {+        "number": "11",+        "name": "EP",+        "type": "power_in",+        "description": "Exposed Thermal Pad (EP); must be connected to VSS."       }     ],     "provenance": {       "extractor": "ds2sf",       "datasheet": {-        "url": "https://datasheet.lcsc.com/datasheet/pdf/3ecd7c892c8368fd4dd78f900871fdca.pdf",-        "pages": 32,-        "sha256": "6b4bfb0f376ed244",+        "url": "https://ww1.microchip.com/downloads/aemDocuments/documents/APID/ProductDocuments/DataSheets/MCP73833-4-Stand-Alone-Linear-Li-Ion-Li-Polymer-Charge-Management-Controller-DS20002005.pdf",+        "pages": 29,+        "sha256": "814b6082bd5076db",         "source_tier": "mfr"       },       "cad": "KiCad official (CC-BY-SA 4.0)",       "pins": {-        "total": 10,-        "described": 10,+        "total": 11,+        "described": 11,         "cites_pages": true,         "refuses_to_fabricate": true       }@@ -120,15 +145,15 @@         "origin": "footprint origin = pad-pattern centre",         "seat": "z = 0",         "extents_mm": [-          3.0,+          3,           2.98,           0.77         ],-        "zmin_mm": 0.0,-        "centre_offset_mm": 0.0,+        "zmin_mm": 0,+        "centre_offset_mm": 0,         "footprint_binding": "identity",         "sha256": "738e2eb45860c11759f8e4f44ab26932b7c15e4d5d6c8c9ac22ae866a3e38711",-        "checked": "2026-10-07",+        "checked": "2026-11-12",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       },       {@@ -139,15 +164,15 @@         "origin": "footprint origin = pad-pattern centre",         "seat": "z = 0",         "extents_mm": [-          3.0,+          3,           2.98,           0.77         ],-        "zmin_mm": 0.0,-        "centre_offset_mm": 0.0,+        "zmin_mm": 0,+        "centre_offset_mm": 0,         "footprint_binding": "identity",-        "sha256": "76189f00804ae8e6292211683fdd11778551f610f09e58834a54555c012afa54",-        "checked": "2026-10-07",+        "sha256": "eb6035fd8ca1f8552be90a9d7f53bee1af731c8a7db09e4553b8436de34a0847",+        "checked": "2026-11-12",         "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"       }     ]@@ -187,12 +212,13 @@     "mcp73833t-ami.kicad_mod",     "mcp73833t-ami.glb",     "mcp73833t-ami.step",-    "mcp73833t-ami-etched.step",     "mcp73833t-ami.lbr",     "docs/hero.png",     "docs/mcp73833t-ami-datasheet.pdf",     "viewers/symbol.html",-    "viewers/footprint.html"+    "viewers/footprint.html",+    "mcp73833t-ami-hero.glb",+    "mcp73833t-ami-hero.overlay.json"   ],   "visibility": {     "public": true@@ -207,5 +233,7 @@       "kind": "packaging"     }   ],-  "updated_at": "2026-09-25T01:26:05.249Z"-}+  "updated_at": "2026-09-25T01:26:05.249Z",+  "description": "Microchip Tech Battery Management, DFN-10-EP(3x3). Pinout settled in review by an AI reviewer against the manufacturer's datasheet, KiCad symbol/footprint/3D.",+  "org": "adom"+}\ No newline at end of file
viewers/footprint.html+1−65
@@ -1,65 +1 @@-<!doctype html><html lang=en><head><meta charset=utf-8>-<meta name=viewport content="width=device-width,initial-scale=1"><title>RAY/MCP73833T-AMI footprint</title>-<style>-:root{--bg:#0d1117;--panel:#161b22;--edge:#30363d;--ink:#e6edf3;--mut:#8b949e;--acc:#00b8b0;--accb:#00e6dc;--hi:#6ea8fe}-*{box-sizing:border-box;margin:0}html,body{height:100%}-body{background:var(--bg);color:var(--ink);font-family:'Satoshi',system-ui,sans-serif;display:flex;flex-direction:column}-.bar{display:flex;flex-wrap:wrap;align-items:center;gap:8px;padding:8px 11px;border-bottom:1px solid var(--edge);flex:none}-.bar .h{font-size:11px;text-transform:uppercase;letter-spacing:.06em;color:var(--mut);font-weight:700}-.bar .sp{flex:1}-.lyrtog{display:inline-flex;align-items:center;gap:6px;font-size:11px;color:var(--mut);background:#1a2130;border:1px solid var(--edge);border-radius:999px;padding:3px 9px;cursor:pointer;user-select:none}-.lyrtog.on{color:var(--ink);border-color:#485162}.lyrtog:not(.on){opacity:.5}-.lyrtog .d{width:8px;height:8px;border-radius:50%;background:#485162}-.stage{flex:1;min-height:0;position:relative;overflow:hidden;background:var(--bg);cursor:grab;touch-action:none}-.stage.drag{cursor:grabbing}-.stage svg{position:absolute;inset:0;width:100%;height:100%}-.pingroup,.pad{cursor:pointer}-.pingroup.hi .pinvis{stroke:var(--hi)!important;stroke-width:7}-rect.pad.hi{stroke:var(--hi);stroke-width:.15;paint-order:stroke}-.lyr-off{display:none}-#tip{position:fixed;z-index:99;pointer-events:none;display:none;max-width:250px;background:#0d1117;border:1px solid var(--acc);border-radius:8px;padding:7px 10px;box-shadow:0 8px 26px #000a}-#tip .tn{font:700 12px ui-monospace,monospace;color:var(--accb)}-#tip .tt{font-size:10px;text-transform:uppercase;letter-spacing:.04em;color:var(--mut);margin-top:1px}-#tip .td{font-size:11px;color:var(--ink);margin-top:5px;line-height:1.4}-</style></head><body>-<div class=bar><span class=h>PCB footprint</span><span class=sp></span><button class="lyrtog on" data-lyr="copper"><span class="d" style="background:#e35d5d"></span>Copper</button><button class="lyrtog on" data-lyr="silk"><span class="d" style="background:#e6edf3"></span>Silkscreen</button><button class="lyrtog" data-lyr="fab"><span class="d" style="background:#8b949e"></span>Fab</button><button class="lyrtog" data-lyr="courtyard"><span class="d" style="background:#bc8cff"></span>Courtyard</button></div>-<div class=stage id=stage><svg xmlns='http://www.w3.org/2000/svg' viewBox='-2.550 -2.250 5.100 4.500' style='width:100%;height:100%'><line class='ly-silk' x1='-1.500' y1='-1.610' x2='1.500' y2='-1.610' stroke='#d8b4fe' stroke-width='0.120'/><line class='ly-silk' x1='-1.500' y1='1.610' x2='1.500' y2='1.610' stroke='#d8b4fe' stroke-width='0.120'/><line class='ly-courtyard' x1='-2.150' y1='-1.850' x2='-2.150' y2='1.850' stroke='#4ade80' stroke-width='0.050'/><line class='ly-courtyard' x1='-2.150' y1='-1.850' x2='2.150' y2='-1.850' stroke='#4ade80' stroke-width='0.050'/><line class='ly-courtyard' x1='-2.150' y1='1.850' x2='2.150' y2='1.850' stroke='#4ade80' stroke-width='0.050'/><line class='ly-courtyard' x1='2.150' y1='-1.850' x2='2.150' y2='1.850' stroke='#4ade80' stroke-width='0.050'/><line class='ly-fab' x1='-1.500' y1='-0.750' x2='-0.750' y2='-1.500' stroke='#f472b6' stroke-width='0.100'/><line class='ly-fab' x1='-1.500' y1='1.500' x2='-1.500' y2='-0.750' stroke='#f472b6' stroke-width='0.100'/><line class='ly-fab' x1='-0.750' y1='-1.500' x2='1.500' y2='-1.500' stroke='#f472b6' stroke-width='0.100'/><line class='ly-fab' x1='1.500' y1='-1.500' x2='1.500' y2='1.500' stroke='#f472b6' stroke-width='0.100'/><line class='ly-fab' x1='1.500' y1='1.500' x2='-1.500' y2='1.500' stroke='#f472b6' stroke-width='0.100'/><rect class='ly-copper pad' data-num='' data-name='' x='-0.688' y='-1.145' width='0.600' height='1.050' rx='0.000' fill='#f59e0b' stroke='#00000033' stroke-width='0.03' opacity='0.94'/><text class='padnum' x='-0.388' y='-0.620' font-size='0.360' transform='rotate(-90 -0.388 -0.620)' fill='#1c1206' text-anchor='middle' dominant-baseline='central' pointer-events='none' font-family='ui-monospace,monospace' font-weight='700'></text><rect class='ly-copper pad' data-num='' data-name='' x='-0.688' y='0.095' width='0.600' height='1.050' rx='0.000' fill='#f59e0b' stroke='#00000033' stroke-width='0.03' opacity='0.94'/><text class='padnum' x='-0.388' y='0.620' font-size='0.360' transform='rotate(-90 -0.388 0.620)' fill='#1c1206' text-anchor='middle' dominant-baseline='central' pointer-events='none' font-family='ui-monospace,monospace' font-weight='700'></text><rect class='ly-copper pad' data-num='' data-name='' x='0.088' y='-1.145' width='0.600' height='1.050' rx='0.000' fill='#f59e0b' stroke='#00000033' stroke-width='0.03' opacity='0.94'/><text class='padnum' x='0.388' y='-0.620' font-size='0.360' transform='rotate(-90 0.388 -0.620)' fill='#1c1206' text-anchor='middle' dominant-baseline='central' pointer-events='none' font-family='ui-monospace,monospace' font-weight='700'></text><rect class='ly-copper pad' data-num='' data-name='' x='0.088' y='0.095' width='0.600' height='1.050' rx='0.000' fill='#f59e0b' stroke='#00000033' stroke-width='0.03' opacity='0.94'/><text class='padnum' x='0.388' y='0.620' font-size='0.360' transform='rotate(-90 0.388 0.620)' fill='#1c1206' text-anchor='middle' dominant-baseline='central' pointer-events='none' font-family='ui-monospace,monospace' font-weight='700'></text><rect class='ly-copper pad' data-num='1' data-name='VDD' x='-1.875' y='-1.150' width='0.650' height='0.300' rx='0.000' fill='#f59e0b' stroke='#00000033' stroke-width='0.03' opacity='0.94'/><text class='padnum' x='-1.550' y='-1.000' font-size='0.350' fill='#1c1206' text-anchor='middle' dominant-baseline='central' pointer-events='none' font-family='ui-monospace,monospace' font-weight='700'>1</text><rect class='ly-copper pad' data-num='2' data-name='VDD' x='-1.875' y='-0.650' width='0.650' height='0.300' rx='0.000' fill='#f59e0b' stroke='#00000033' stroke-width='0.03' opacity='0.94'/><text class='padnum' x='-1.550' y='-0.500' font-size='0.350' fill='#1c1206' text-anchor='middle' dominant-baseline='central' pointer-events='none' font-family='ui-monospace,monospace' font-weight='700'>2</text><rect class='ly-copper pad' data-num='3' data-name='STAT1' x='-1.875' y='-0.150' width='0.650' height='0.300' rx='0.000' fill='#f59e0b' stroke='#00000033' stroke-width='0.03' opacity='0.94'/><text class='padnum' x='-1.550' y='0.000' font-size='0.350' fill='#1c1206' text-anchor='middle' dominant-baseline='central' pointer-events='none' font-family='ui-monospace,monospace' font-weight='700'>3</text><rect class='ly-copper pad' data-num='4' data-name='STAT2' x='-1.875' y='0.350' width='0.650' height='0.300' rx='0.000' fill='#f59e0b' stroke='#00000033' stroke-width='0.03' opacity='0.94'/><text class='padnum' x='-1.550' y='0.500' font-size='0.350' fill='#1c1206' text-anchor='middle' dominant-baseline='central' pointer-events='none' font-family='ui-monospace,monospace' font-weight='700'>4</text><rect class='ly-copper pad' data-num='5' data-name='VSS' x='-1.875' y='0.850' width='0.650' height='0.300' rx='0.000' fill='#f59e0b' stroke='#00000033' stroke-width='0.03' opacity='0.94'/><text class='padnum' x='-1.550' y='1.000' font-size='0.350' fill='#1c1206' text-anchor='middle' dominant-baseline='central' pointer-events='none' font-family='ui-monospace,monospace' font-weight='700'>5</text><rect class='ly-copper pad' data-num='6' data-name='PROG' x='1.225' y='0.850' width='0.650' height='0.300' rx='0.000' fill='#f59e0b' stroke='#00000033' stroke-width='0.03' opacity='0.94'/><text class='padnum' x='1.550' y='1.000' font-size='0.350' fill='#1c1206' text-anchor='middle' dominant-baseline='central' pointer-events='none' font-family='ui-monospace,monospace' font-weight='700'>6</text><rect class='ly-copper pad' data-num='7' data-name='PG' x='1.225' y='0.350' width='0.650' height='0.300' rx='0.000' fill='#f59e0b' stroke='#00000033' stroke-width='0.03' opacity='0.94'/><text class='padnum' x='1.550' y='0.500' font-size='0.350' fill='#1c1206' text-anchor='middle' dominant-baseline='central' pointer-events='none' font-family='ui-monospace,monospace' font-weight='700'>7</text><rect class='ly-copper pad' data-num='8' data-name='THERM' x='1.225' y='-0.150' width='0.650' height='0.300' rx='0.000' fill='#f59e0b' stroke='#00000033' stroke-width='0.03' opacity='0.94'/><text class='padnum' x='1.550' y='0.000' font-size='0.350' fill='#1c1206' text-anchor='middle' dominant-baseline='central' pointer-events='none' font-family='ui-monospace,monospace' font-weight='700'>8</text><rect class='ly-copper pad' data-num='9' data-name='VBAT' x='1.225' y='-0.650' width='0.650' height='0.300' rx='0.000' fill='#f59e0b' stroke='#00000033' stroke-width='0.03' opacity='0.94'/><text class='padnum' x='1.550' y='-0.500' font-size='0.350' fill='#1c1206' text-anchor='middle' dominant-baseline='central' pointer-events='none' font-family='ui-monospace,monospace' font-weight='700'>9</text><rect class='ly-copper pad' data-num='10' data-name='VBAT' x='1.225' y='-1.150' width='0.650' height='0.300' rx='0.000' fill='#f59e0b' stroke='#00000033' stroke-width='0.03' opacity='0.94'/><text class='padnum' x='1.550' y='-1.000' font-size='0.350' fill='#1c1206' text-anchor='middle' dominant-baseline='central' pointer-events='none' font-family='ui-monospace,monospace' font-weight='700'>10</text><rect class='ly-copper pad' data-num='11' data-name='' x='-0.775' y='-1.240' width='1.550' height='2.480' rx='0.000' fill='#f59e0b' stroke='#00000033' stroke-width='0.03' opacity='0.94'/><text class='padnum' x='0.000' y='0.000' font-size='0.930' transform='rotate(-90 0.000 0.000)' fill='#1c1206' text-anchor='middle' dominant-baseline='central' pointer-events='none' font-family='ui-monospace,monospace' font-weight='700'>11</text></svg></div>-<div id=tip></div>-<script>-var KIND="footprint", MPN="RAY/MCP73833T-AMI", PINS=[{"desc":"","name":"VDD","number":"1","type":""},{"desc":"","name":"VDD","number":"2","type":""},{"desc":"","name":"STAT1","number":"3","type":""},{"desc":"","name":"STAT2","number":"4","type":""},{"desc":"","name":"VSS","number":"5","type":""},{"desc":"","name":"VBAT","number":"10","type":""},{"desc":"","name":"VBAT","number":"9","type":""},{"desc":"","name":"THERM","number":"8","type":""},{"desc":"","name":"PG","number":"7","type":""},{"desc":"","name":"PROG","number":"6","type":""}];-var byNum={}; PINS.forEach(function(p){byNum[String(p.number)]=p;});-var stage=document.getElementById('stage'), svg=stage.querySelector('svg'), tip=document.getElementById('tip');-// ---- pan/zoom -----var vb=(svg.getAttribute('viewBox')||'0 0 100 100').split(/\s+/).map(Number), base=vb.slice();-function setVB(){svg.setAttribute('viewBox',vb.join(' '));}-stage.addEventListener('wheel',function(e){e.preventDefault();var r=stage.getBoundingClientRect();var mx=(e.clientX-r.left)/r.width,my=(e.clientY-r.top)/r.height;var f=e.deltaY<0?0.88:1.14;var nw=vb[2]*f,nh=vb[3]*f;vb[0]+=(vb[2]-nw)*mx;vb[1]+=(vb[3]-nh)*my;vb[2]=nw;vb[3]=nh;setVB();},{passive:false});-var pan=null;-stage.addEventListener('pointerdown',function(e){pan={x:e.clientX,y:e.clientY};stage.classList.add('drag');stage.setPointerCapture(e.pointerId);});-stage.addEventListener('pointermove',function(e){if(!pan)return;var r=stage.getBoundingClientRect();vb[0]-=(e.clientX-pan.x)/r.width*vb[2];vb[1]-=(e.clientY-pan.y)/r.height*vb[3];pan={x:e.clientX,y:e.clientY};setVB();});-function endPan(){pan=null;stage.classList.remove('drag');}-stage.addEventListener('pointerup',endPan);stage.addEventListener('pointerleave',endPan);-stage.addEventListener('dblclick',function(){vb=base.slice();setVB();});-// ---- cross-highlight bus -----function els(n){return [].slice.call(document.querySelectorAll('[data-num="'+n+'"]'));}-function clearHi(){[].slice.call(document.querySelectorAll('.hi')).forEach(function(e){e.classList.remove('hi');});}-function hi(n){els(n).forEach(function(e){e.classList.add('hi');});}-function post(n){try{parent.postMessage({type:'lbr-hover',pin:n===null?null:String(n),mpn:MPN},'*');}catch(_){}}-function showTip(n,x,y){var p=byNum[String(n)];if(!p)return;tip.innerHTML='<span class=tn></span><div class=tt></div><div class=td></div>';tip.querySelector('.tn').textContent=n+'  '+(p.name||'');tip.querySelector('.tt').textContent=p.type||'';var d=p.desc||'';if(d)tip.querySelector('.td').textContent=d;else tip.querySelector('.td').style.display='none';tip.style.display='block';tip.style.left=(x+14)+'px';tip.style.top=(y+12)+'px';}-[].slice.call(document.querySelectorAll('.pingroup,.pad')).forEach(function(g){-  var n=g.getAttribute('data-num');-  g.addEventListener('mouseenter',function(e){clearHi();hi(n);post(n);showTip(n,e.clientX,e.clientY);});-  g.addEventListener('mousemove',function(e){tip.style.left=(e.clientX+14)+'px';tip.style.top=(e.clientY+12)+'px';});-  g.addEventListener('mouseleave',function(){clearHi();post(null);tip.style.display='none';});-});-window.addEventListener('message',function(e){var d=e.data||{};if(d.type!=='lbr-hover')return;clearHi();if(d.pin!=null)hi(d.pin);});-// ---- footprint layer toggles -----[].slice.call(document.querySelectorAll('.lyrtog')).forEach(function(b){-  function apply(on){[].slice.call(document.querySelectorAll('.ly-'+b.getAttribute('data-lyr'))).forEach(function(el){el.classList.toggle('lyr-off',!on);});}-  apply(b.classList.contains('on'));-  b.addEventListener('click',function(){apply(b.classList.toggle('on'));});-});-// ---- auto-grow the host readme iframe -----function ph(){var h=Math.max(360,Math.min(16000,document.body.scrollHeight||420));parent.postMessage({type:'readme-height',height:h},'*');}-window.addEventListener('load',ph);setTimeout(ph,300);-</script>-</body></html>+<!doctype html><title>mcp73833t-ami</title>\ No newline at end of file
viewers/symbol.html+1−65
@@ -1,65 +1 @@-<!doctype html><html lang=en><head><meta charset=utf-8>-<meta name=viewport content="width=device-width,initial-scale=1"><title>RAY/MCP73833T-AMI symbol</title>-<style>-:root{--bg:#0d1117;--panel:#161b22;--edge:#30363d;--ink:#e6edf3;--mut:#8b949e;--acc:#00b8b0;--accb:#00e6dc;--hi:#6ea8fe}-*{box-sizing:border-box;margin:0}html,body{height:100%}-body{background:var(--bg);color:var(--ink);font-family:'Satoshi',system-ui,sans-serif;display:flex;flex-direction:column}-.bar{display:flex;flex-wrap:wrap;align-items:center;gap:8px;padding:8px 11px;border-bottom:1px solid var(--edge);flex:none}-.bar .h{font-size:11px;text-transform:uppercase;letter-spacing:.06em;color:var(--mut);font-weight:700}-.bar .sp{flex:1}-.lyrtog{display:inline-flex;align-items:center;gap:6px;font-size:11px;color:var(--mut);background:#1a2130;border:1px solid var(--edge);border-radius:999px;padding:3px 9px;cursor:pointer;user-select:none}-.lyrtog.on{color:var(--ink);border-color:#485162}.lyrtog:not(.on){opacity:.5}-.lyrtog .d{width:8px;height:8px;border-radius:50%;background:#485162}-.stage{flex:1;min-height:0;position:relative;overflow:hidden;background:var(--bg);cursor:grab;touch-action:none}-.stage.drag{cursor:grabbing}-.stage svg{position:absolute;inset:0;width:100%;height:100%}-.pingroup,.pad{cursor:pointer}-.pingroup.hi .pinvis{stroke:var(--hi)!important;stroke-width:7}-rect.pad.hi{stroke:var(--hi);stroke-width:.15;paint-order:stroke}-.lyr-off{display:none}-#tip{position:fixed;z-index:99;pointer-events:none;display:none;max-width:250px;background:#0d1117;border:1px solid var(--acc);border-radius:8px;padding:7px 10px;box-shadow:0 8px 26px #000a}-#tip .tn{font:700 12px ui-monospace,monospace;color:var(--accb)}-#tip .tt{font-size:10px;text-transform:uppercase;letter-spacing:.04em;color:var(--mut);margin-top:1px}-#tip .td{font-size:11px;color:var(--ink);margin-top:5px;line-height:1.4}-</style></head><body>-<div class=bar><span class=h>Schematic symbol</span><span class=sp></span></div>-<div class=stage id=stage><svg xmlns='http://www.w3.org/2000/svg' viewBox='-750 -350 1500 700' style='width:100%;height:100%'><rect x='-500.0' y='-300.0' width='1000.0' height='600.0' fill='#e35d5d22' stroke='#e35d5d' stroke-width='4'/><g class='pingroup' data-num='1' data-name='VDD'><line class='pinvis' x1='-700.0' y1='-200.0' x2='-500.0' y2='-200.0' stroke='#dfe4ec' stroke-width='4'/><line x1='-700.0' y1='-200.0' x2='-500.0' y2='-200.0' stroke='transparent' stroke-width='26' pointer-events='stroke'/></g><text x='-600.0' y='-155.0' font-size='60' fill='#9fb0c8' text-anchor='middle' dominant-baseline='central'>1</text><text x='-470.0' y='-200.0' font-size='60' fill='#e6e9ef' text-anchor='start' dominant-baseline='central'>VDD</text><g class='pingroup' data-num='2' data-name='VDD'><line class='pinvis' x1='-700.0' y1='-100.0' x2='-500.0' y2='-100.0' stroke='#dfe4ec' stroke-width='4'/><line x1='-700.0' y1='-100.0' x2='-500.0' y2='-100.0' stroke='transparent' stroke-width='26' pointer-events='stroke'/></g><text x='-600.0' y='-55.0' font-size='60' fill='#9fb0c8' text-anchor='middle' dominant-baseline='central'>2</text><text x='-470.0' y='-100.0' font-size='60' fill='#e6e9ef' text-anchor='start' dominant-baseline='central'>VDD</text><g class='pingroup' data-num='3' data-name='STAT1'><line class='pinvis' x1='-700.0' y1='-0.0' x2='-500.0' y2='-0.0' stroke='#dfe4ec' stroke-width='4'/><line x1='-700.0' y1='-0.0' x2='-500.0' y2='-0.0' stroke='transparent' stroke-width='26' pointer-events='stroke'/></g><text x='-600.0' y='45.0' font-size='60' fill='#9fb0c8' text-anchor='middle' dominant-baseline='central'>3</text><text x='-470.0' y='0.0' font-size='60' fill='#e6e9ef' text-anchor='start' dominant-baseline='central'>STAT1</text><g class='pingroup' data-num='4' data-name='STAT2'><line class='pinvis' x1='-700.0' y1='100.0' x2='-500.0' y2='100.0' stroke='#dfe4ec' stroke-width='4'/><line x1='-700.0' y1='100.0' x2='-500.0' y2='100.0' stroke='transparent' stroke-width='26' pointer-events='stroke'/></g><text x='-600.0' y='145.0' font-size='60' fill='#9fb0c8' text-anchor='middle' dominant-baseline='central'>4</text><text x='-470.0' y='100.0' font-size='60' fill='#e6e9ef' text-anchor='start' dominant-baseline='central'>STAT2</text><g class='pingroup' data-num='5' data-name='VSS'><line class='pinvis' x1='-700.0' y1='200.0' x2='-500.0' y2='200.0' stroke='#dfe4ec' stroke-width='4'/><line x1='-700.0' y1='200.0' x2='-500.0' y2='200.0' stroke='transparent' stroke-width='26' pointer-events='stroke'/></g><text x='-600.0' y='245.0' font-size='60' fill='#9fb0c8' text-anchor='middle' dominant-baseline='central'>5</text><text x='-470.0' y='200.0' font-size='60' fill='#e6e9ef' text-anchor='start' dominant-baseline='central'>VSS</text><g class='pingroup' data-num='10' data-name='VBAT'><line class='pinvis' x1='700.0' y1='-200.0' x2='500.0' y2='-200.0' stroke='#dfe4ec' stroke-width='4'/><line x1='700.0' y1='-200.0' x2='500.0' y2='-200.0' stroke='transparent' stroke-width='26' pointer-events='stroke'/></g><text x='600.0' y='-245.0' font-size='60' fill='#9fb0c8' text-anchor='middle' dominant-baseline='central'>10</text><text x='470.0' y='-200.0' font-size='60' fill='#e6e9ef' text-anchor='end' dominant-baseline='central'>VBAT</text><g class='pingroup' data-num='9' data-name='VBAT'><line class='pinvis' x1='700.0' y1='-100.0' x2='500.0' y2='-100.0' stroke='#dfe4ec' stroke-width='4'/><line x1='700.0' y1='-100.0' x2='500.0' y2='-100.0' stroke='transparent' stroke-width='26' pointer-events='stroke'/></g><text x='600.0' y='-145.0' font-size='60' fill='#9fb0c8' text-anchor='middle' dominant-baseline='central'>9</text><text x='470.0' y='-100.0' font-size='60' fill='#e6e9ef' text-anchor='end' dominant-baseline='central'>VBAT</text><g class='pingroup' data-num='8' data-name='THERM'><line class='pinvis' x1='700.0' y1='-0.0' x2='500.0' y2='-0.0' stroke='#dfe4ec' stroke-width='4'/><line x1='700.0' y1='-0.0' x2='500.0' y2='-0.0' stroke='transparent' stroke-width='26' pointer-events='stroke'/></g><text x='600.0' y='-45.0' font-size='60' fill='#9fb0c8' text-anchor='middle' dominant-baseline='central'>8</text><text x='470.0' y='0.0' font-size='60' fill='#e6e9ef' text-anchor='end' dominant-baseline='central'>THERM</text><g class='pingroup' data-num='7' data-name='PG'><line class='pinvis' x1='700.0' y1='100.0' x2='500.0' y2='100.0' stroke='#dfe4ec' stroke-width='4'/><line x1='700.0' y1='100.0' x2='500.0' y2='100.0' stroke='transparent' stroke-width='26' pointer-events='stroke'/></g><text x='600.0' y='55.0' font-size='60' fill='#9fb0c8' text-anchor='middle' dominant-baseline='central'>7</text><text x='470.0' y='100.0' font-size='60' fill='#e6e9ef' text-anchor='end' dominant-baseline='central'>PG</text><g class='pingroup' data-num='6' data-name='PROG'><line class='pinvis' x1='700.0' y1='200.0' x2='500.0' y2='200.0' stroke='#dfe4ec' stroke-width='4'/><line x1='700.0' y1='200.0' x2='500.0' y2='200.0' stroke='transparent' stroke-width='26' pointer-events='stroke'/></g><text x='600.0' y='155.0' font-size='60' fill='#9fb0c8' text-anchor='middle' dominant-baseline='central'>6</text><text x='470.0' y='200.0' font-size='60' fill='#e6e9ef' text-anchor='end' dominant-baseline='central'>PROG</text></svg></div>-<div id=tip></div>-<script>-var KIND="symbol", MPN="RAY/MCP73833T-AMI", PINS=[{"desc":"","name":"VDD","number":"1","type":""},{"desc":"","name":"VDD","number":"2","type":""},{"desc":"","name":"STAT1","number":"3","type":""},{"desc":"","name":"STAT2","number":"4","type":""},{"desc":"","name":"VSS","number":"5","type":""},{"desc":"","name":"VBAT","number":"10","type":""},{"desc":"","name":"VBAT","number":"9","type":""},{"desc":"","name":"THERM","number":"8","type":""},{"desc":"","name":"PG","number":"7","type":""},{"desc":"","name":"PROG","number":"6","type":""}];-var byNum={}; PINS.forEach(function(p){byNum[String(p.number)]=p;});-var stage=document.getElementById('stage'), svg=stage.querySelector('svg'), tip=document.getElementById('tip');-// ---- pan/zoom -----var vb=(svg.getAttribute('viewBox')||'0 0 100 100').split(/\s+/).map(Number), base=vb.slice();-function setVB(){svg.setAttribute('viewBox',vb.join(' '));}-stage.addEventListener('wheel',function(e){e.preventDefault();var r=stage.getBoundingClientRect();var mx=(e.clientX-r.left)/r.width,my=(e.clientY-r.top)/r.height;var f=e.deltaY<0?0.88:1.14;var nw=vb[2]*f,nh=vb[3]*f;vb[0]+=(vb[2]-nw)*mx;vb[1]+=(vb[3]-nh)*my;vb[2]=nw;vb[3]=nh;setVB();},{passive:false});-var pan=null;-stage.addEventListener('pointerdown',function(e){pan={x:e.clientX,y:e.clientY};stage.classList.add('drag');stage.setPointerCapture(e.pointerId);});-stage.addEventListener('pointermove',function(e){if(!pan)return;var r=stage.getBoundingClientRect();vb[0]-=(e.clientX-pan.x)/r.width*vb[2];vb[1]-=(e.clientY-pan.y)/r.height*vb[3];pan={x:e.clientX,y:e.clientY};setVB();});-function endPan(){pan=null;stage.classList.remove('drag');}-stage.addEventListener('pointerup',endPan);stage.addEventListener('pointerleave',endPan);-stage.addEventListener('dblclick',function(){vb=base.slice();setVB();});-// ---- cross-highlight bus -----function els(n){return [].slice.call(document.querySelectorAll('[data-num="'+n+'"]'));}-function clearHi(){[].slice.call(document.querySelectorAll('.hi')).forEach(function(e){e.classList.remove('hi');});}-function hi(n){els(n).forEach(function(e){e.classList.add('hi');});}-function post(n){try{parent.postMessage({type:'lbr-hover',pin:n===null?null:String(n),mpn:MPN},'*');}catch(_){}}-function showTip(n,x,y){var p=byNum[String(n)];if(!p)return;tip.innerHTML='<span class=tn></span><div class=tt></div><div class=td></div>';tip.querySelector('.tn').textContent=n+'  '+(p.name||'');tip.querySelector('.tt').textContent=p.type||'';var d=p.desc||'';if(d)tip.querySelector('.td').textContent=d;else tip.querySelector('.td').style.display='none';tip.style.display='block';tip.style.left=(x+14)+'px';tip.style.top=(y+12)+'px';}-[].slice.call(document.querySelectorAll('.pingroup,.pad')).forEach(function(g){-  var n=g.getAttribute('data-num');-  g.addEventListener('mouseenter',function(e){clearHi();hi(n);post(n);showTip(n,e.clientX,e.clientY);});-  g.addEventListener('mousemove',function(e){tip.style.left=(e.clientX+14)+'px';tip.style.top=(e.clientY+12)+'px';});-  g.addEventListener('mouseleave',function(){clearHi();post(null);tip.style.display='none';});-});-window.addEventListener('message',function(e){var d=e.data||{};if(d.type!=='lbr-hover')return;clearHi();if(d.pin!=null)hi(d.pin);});-// ---- footprint layer toggles -----[].slice.call(document.querySelectorAll('.lyrtog')).forEach(function(b){-  function apply(on){[].slice.call(document.querySelectorAll('.ly-'+b.getAttribute('data-lyr'))).forEach(function(el){el.classList.toggle('lyr-off',!on);});}-  apply(b.classList.contains('on'));-  b.addEventListener('click',function(){apply(b.classList.toggle('on'));});-});-// ---- auto-grow the host readme iframe -----function ph(){var h=Math.max(360,Math.min(16000,document.body.scrollHeight||420));parent.postMessage({type:'readme-height',height:h},'*');}-window.addEventListener('load',ph);setTimeout(ph,300);-</script>-</body></html>+<!doctype html><title>mcp73833t-ami</title>\ No newline at end of file