← Commit history

mcp73833t-ami: factory component page (tier=mfr)

Ray ·6471bcd748 · ·parent e4265b2
1 file changed +128−8
page.json+128−8
@@ -1,13 +1,138 @@ {+  "schema_version": 1,+  "type": "component",   "slug": "mcp73833t-ami",+  "title": "MCP73833T-AMI",+  "brief": "Microchip Battery Management, DFN-10-EP(3x3). Datasheet-verified pinout, KiCad symbol/footprint/3D.",   "version": "0.1.0",-  "type": "component",-  "description": "Microchip Battery Management, DFN-10-EP(3x3). Datasheet-verified pinout, KiCad symbol/footprint/3D.",+  "license": "CC-BY-SA-4.0",   "tags": [     "component",     "pmic",     "mcp73833t-ami"   ],+  "component": {+    "mpn": "MCP73833T-AMI",+    "manufacturer": "Microchip",+    "package": "DFN-10-EP(3x3)",+    "pin_count": 10,+    "category": "PMIC",+    "subcategory": "Battery Management",+    "datasheet": "https://datasheet.lcsc.com/datasheet/pdf/3ecd7c892c8368fd4dd78f900871fdca.pdf",+    "parts": {+      "symbol": "mcp73833t-ami.kicad_sym",+      "footprint": "mcp73833t-ami.kicad_mod",+      "model_3d": "mcp73833t-ami.glb",+      "model_3d_step": "mcp73833t-ami.step",+      "lbr": "mcp73833t-ami.lbr"+    },+    "distributor_links": {},+    "pins": [+      {+        "number": "1",+        "name": "VDD",+        "type": "power_in",+        "description": "Battery management input supply. Recommended supply of [VREG(typ) + 0.3 V] up to 6 V (absolute max 7.0 V). Bypass to VSS with a minimum of 1 uF. Pins 1 and 2 are internally tied together and both must be connected."+      },+      {+        "number": "2",+        "name": "VDD",+        "type": "power_in",+        "description": "Battery management input supply (paralleled with pin 1). Both VDD pins must be connected to the input supply."+      },+      {+        "number": "3",+        "name": "STAT1",+        "type": "output",+        "description": "Charge status output 1. Open-drain output for LED (through a series resistor, typ. 470 ohm) or MCU logic input. Sink current 15 mA typ, 25 mA max; VOL <= 0.4 V at ISINK = 4 mA. Low during preconditioning / fast charge / constant voltage; Hi-Z in standby/shutdown/charge-complete."+      },+      {+        "number": "4",+        "name": "STAT2",+        "type": "output",+        "description": "Charge status output 2. Open-drain output for LED or MCU logic input. Combined with STAT1 and PG encodes the charger state per the state flow chart (e.g. STAT2 = LOW only in charge-complete)."+      },+      {+        "number": "5",+        "name": "VSS",+        "type": "power_in",+        "description": "Battery management 0 V reference. Connect to negative terminal of the battery and the input supply return. Exposed pad on DFN variant is internally tied to VSS."+      },+      {+        "number": "6",+        "name": "PROG",+        "type": "input",+        "description": "Current regulation set and charge control enable. Program the fast-charge current via a resistor from PROG to VSS using IREG = 1000 V / RPROG (RPROG in kohm). Valid range 1 kohm to 20 kohm (100 mA to 1 A). Floating this pin (>200 kohm) disables the charger and enters standby."+      },+      {+        "number": "7",+        "name": "PG",+        "type": "output",+        "description": "Power Good indication (MCP73833 variant). Pseudo open-drain output; can sink current but has an internal diode path back to VDD, so it must only be pulled up to VDD (not a higher rail). Asserted low whenever VDD is above UVLO and greater than VBAT. On the MCP73834 variant this pin is the Timer Enable (TE) input instead."+      },+      {+        "number": "8",+        "name": "THERM",+        "type": "input",+        "description": "Thermistor input for cell temperature monitoring. Sources ~50 uA (47-53 uA) into an external NTC (nominally 10 kohm) tied to VSS. Comparators trip at VT1 = 1.23 V (upper, high temp) and VT2 = 0.25 V (lower, low temp) versus VTHERM. Tie to VSS through a resistor if unused (comparators disabled by pulling above (VDD-0.1 V) enters System Test / LDO mode)."+      },+      {+        "number": "9",+        "name": "VBAT",+        "type": "power_out",+        "description": "Battery charge control output (drain of the internal P-channel MOSFET pass device, RDSON ~300 mohm). Connect to the positive terminal of the Li-Ion/Li-Polymer cell. Pins 9 and 10 are internally paralleled and both must be connected. Bypass to VSS with a minimum of 1 uF for loop stability when the battery is disconnected."+      },+      {+        "number": "10",+        "name": "VBAT",+        "type": "power_out",+        "description": "Battery charge control output (paralleled with pin 9). Both VBAT pins must be connected to the cell positive terminal."+      }+    ],+    "provenance": {+      "extractor": "ds2sf",+      "datasheet": {+        "url": "https://datasheet.lcsc.com/datasheet/pdf/3ecd7c892c8368fd4dd78f900871fdca.pdf",+        "pages": 32,+        "sha256": "6b4bfb0f376ed244",+        "source_tier": "mfr"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 10,+        "described": 10,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "metadata": {+    "specs": {+      "Manufacturer": "Microchip",+      "Package": "DFN-10-EP(3x3)",+      "Category": "PMIC",+      "Pins": "10"+    }+  },+  "sections": [+    "hero",+    "viewers",+    "readme",+    "breadcrumbs",+    "info"+  ],+  "discovery_triggers": [+    "mcp73833t-ami"+  ],+  "discovery_pitch": "MCP73833T-AMI (Microchip) component page with datasheet-verified CAD.",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  },   "dependencies": {},   "hero": {     "type": "image",@@ -25,10 +150,5 @@     "docs/mcp73833t-ami-datasheet.pdf",     "viewers/symbol.html",     "viewers/footprint.html"-  ],-  "visibility": "public",-  "author": {-    "name": "Ray",-    "email": "[email protected]"-  }+  ] }\ No newline at end of file