Generated by kicad-footprint-generator · KiCad file format 20260206
MCP73833-CNI
Microchip Tech · Pre-ordered MCUs · MSOP-10
MCP73833-CNI from Microchip Tech, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Battery management input supply; a voltage of [VREG (typical) + 0.3V] to 6V is recommended, bypassed to VSS with a minimum of 1 µF. |
| 2 | VDD | power_in | Battery management input supply (second VDD pin); recommended [VREG (typical) + 0.3V] to 6V, bypassed to VSS with a minimum of 1 µF. |
| 3 | STAT1 | output | Open-drain logic charge status output for connection to an LED or, with a pull-up resistor, to a host microcontroller. |
| 4 | STAT2 | output | Open-drain logic charge status output for connection to an LED or, with a pull-up resistor, to a host microcontroller. |
| 5 | VSS | power_in | Battery management 0V reference; connect to the negative terminal of the battery and input supply. |
| 6 | PROG | passive | Current regulation set: a resistor from PROG to VSS scales the preconditioning, fast charge and termination currents, and floating the pin disables the charge controller. |
| 7 | PG | output | MCP73833 power good pseudo open-drain output that sinks but cannot source current, should only be pulled up to the input, and is low whenever the input is above the UVLO threshold and greater than the battery voltage (this pin is TE timer enable input on the MCP73834). |
| 8 | THERM | input | Thermistor input biased by an internal 50 µA current source for 10 kΩ NTC thermistors, compared against factory-set thresholds of 1.20V and 0.25V typically. |
| 9 | VBAT | power_out | Battery charge control output connected to the positive battery terminal (drain of the internal P-channel MOSFET pass transistor), bypassed to VSS with a minimum of 1 µF for loop stability. |
| 10 | VBAT | power_out | Battery charge control output connected to the positive battery terminal (drain of the internal P-channel MOSFET pass transistor), bypassed to VSS with a minimum of 1 µF for loop stability. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-10 |
| Category | Embedded Processors & Controllers |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VDD | 7 | V | 3 | |||
| All inputs and outputs w.r.t. VSS (lower limit) | -0.3 | V | upper limit is (VDD+0.3)V | 3 | |||
| Storage temperature | -65 | 150 | °C | 3 | |||
| ESD HBM | 4 | kV | 1.5 kΩ in series with 100 pF, all pins | 3 | |||
| ESD MM | 300 | V | 200 pF, no series resistance | 3 | |||
| Supply voltage, charging | VDD | 3.75 | 6 | V | Charging | 3 | |
| Supply voltage, charge complete/standby | VDD | 6 | V | Charge Complete, Standby | 3 | ||
| Supply current, charging | ISS | 2000 | 3000 | µA | Charging | 3 | |
| Supply current, charge complete | ISS | 150 | 300 | µA | Charge Complete | 3 | |
| Supply current, standby | ISS | 100 | 300 | µA | Standby (No Battery or PROG Floating) | 3 | |
| Supply current, shutdown | ISS | 50 | 100 | µA | Shutdown (VDD < VBAT, or VDD < VSTOP) | 3 | |
| UVLO start threshold | VSTART | 3.4 | 3.55 | 3.7 | V | VDD Low-to-High | 3 |
| UVLO stop threshold | VSTOP | 3.3 | 3.45 | 3.6 | V | VDD High-to-Low | 3 |
| UVLO hysteresis | VHYS | 100 | mV | 3 | |||
| Line regulation | /(ΔVBAT/VBAT)/ΔVDD/ | 0.1 | 0.3 | %/V | VDD=[VREG(Typical)+1V] to 6V, IOUT=10 mA | 3 | |
| Load regulation | /ΔVBAT/VBAT/ | 0.1 | 0.3 | % | IOUT=10 mA to 100 mA, VDD=[VREG(Typical)+1V] | 3 | |
| Fast charge current regulation | IREG | 90 | 100 | 110 | mA | PROG = 10 kΩ | 3 |
| Fast charge current regulation | IREG | 900 | 1000 | 1100 | mA | PROG = 1.0 kΩ, TA=-5°C to +55°C | 3 |
| Maximum output current limit | IMAX | 1200 | mA | PROG < 833Ω | 3 | ||
| Precondition hysteresis | VPHYS | 100 | mV | VBAT High-to-Low | 4 | ||
| Pass transistor ON-resistance | RDSON | 300 | mΩ | VDD = 3.75V, TJ = 105°C | 4 | ||
| Output reverse leakage current | IDISCHARGE | 0.15 | 2 | µA | PROG Floating | 4 | |
| Output reverse leakage current | IDISCHARGE | 0.25 | 2 | µA | VDD < VBAT | 4 | |
| Output reverse leakage current | IDISCHARGE | -5.5 | -15 | µA | Charge Complete | 4 | |
| Status sink current | ISINK | 15 | 25 | mA | 4 | ||
| Status low output voltage | VOL | 0.4 | 1 | V | ISINK = 4 mA | 4 | |
| Status input leakage current | ILK | 0.01 | 1 | µA | High Impedance, 6V on pin | 4 | |
| PROG charge impedance range | RPROG | 1 | 20 | kΩ | 4 | ||
| PROG standby impedance | RPROG | 70 | 200 | kΩ | Minimum Impedance for Standby | 4 | |
| Thermistor current source | ITHERM | 47 | 50 | 53 | µA | 2 kΩ < RTHERM < 50 kΩ | 4 |
| Thermistor upper trip threshold | VT1 | 1.2 | 1.23 | 1.26 | V | VTHERM Low-to-High | 4 |
| Thermistor upper trip point hysteresis | VT1HYS | -50 | mV | 4 | |||
| Thermistor lower trip threshold | VT2 | 0.235 | 0.25 | 0.265 | V | VTHERM High-to-Low | 4 |
| Thermistor lower trip point hysteresis | VT2HYS | 50 | mV | 4 | |||
| THERM input sink current | ISINK | 3 | 6 | 20 | µA | Stand-by or system test mode | 4 |
| Bypass capacitance | CBAT | 1 | µF | IOUT < 250 mA | 4 | ||
| Bypass capacitance | CBAT | 4.7 | µF | IOUT > 250 mA | 4 | ||
| Timer enable input high voltage | VIH | 2 | V | 5 | |||
| Timer enable input low voltage | VIL | 0.6 | V | 5 | |||
| Timer enable input leakage current | ILK | 0.01 | 1 | µA | VTE = 6V | 5 | |
| Thermal shutdown die temperature | TSD | 150 | °C | 5 | |||
| Thermal shutdown hysteresis | TSDHYS | 10 | °C | 5 | |||
| UVLO start delay | tSTART | 5 | ms | VDD Low-to-High | 5 | ||
| Transition time out of preconditioning | tDELAY | 1 | ms | VBATVPTH | 5 | ||
| Current rise time out of preconditioning | tRISE | 1 | ms | IOUT Rising to 90% of IREG | 5 | ||
| Preconditioning comparator filter time | tPRECON | 0.4 | 1.3 | 3.2 | ms | Average VBAT Rise/Fall | 5 |
| Termination comparator filter time | tTERM | 0.4 | 1.3 | 3.2 | ms | Average IOUT Falling | 5 |
| Charge comparator filter time | tCHARGE | 0.4 | 1.3 | 3.2 | ms | Average VBAT Falling | 5 |
| Thermistor comparator filter time | tTHERM | 0.4 | 1.3 | 3.2 | ms | Average THERM Rise/Fall | 5 |
| Status output turn-off | tOFF | 200 | µs | ISINK = 1 mA to 0 mA | 5 | ||
| Status output turn-on | tON | 200 | µs | ISINK = 0 mA to 1 mA | 5 | ||
| Specified temperature range | TA | -40 | 85 | °C | 5 | ||
| Operating temperature range | TA | -40 | 125 | °C | 5 | ||
| Storage temperature range | TA | -65 | 150 | °C | 5 | ||
| Thermal resistance, MSOP-10 | θJA | 113 | °C/W | 4-Layer JC51-7 Standard Board, Natural Convection | 5 |
CAD (KiCad official)
- Symbol:
MCP73833-CNI - Footprint:
Package_SO:MSOP-10_3x3mm_P0.5mm - 3D model: MSOP-10 (KiCad packages3D, STEP)
- 3D model files:
mcp73833-cni-etched.step/mcp73833-cni-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp73833-cni.step/mcp73833-cni.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (32 pp, sha256
70b297a13b77cebf, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).