main
Ray
mcp73833-bzi-mf: renamed from mcp73833-bzi, the part it was built from (MCP73833-BZI/MF); family listed
f60f2ed
MCP73833-BZI/MF
Microchip Tech · Battery Management ICs · DFN-10(3x3)
MCP73833-BZI from Microchip Tech, in a DFN-10(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Battery management input supply; a supply of [VREG (typical) + 0.3V] to 6V is recommended, bypassed to VSS with a minimum of 1 µF. |
| 2 | VDD | power_in | Battery management input supply; a supply of [VREG (typical) + 0.3V] to 6V is recommended, bypassed to VSS with a minimum of 1 µF. |
| 3 | STAT1 | output | Open-drain charge status output for an LED or a pull-up resistor to a host microcontroller. |
| 4 | STAT2 | output | Open-drain charge status output for an LED or a pull-up resistor to a host microcontroller. |
| 5 | VSS | power_in | Battery management 0V reference; connect to the negative terminal of the battery and the input supply. |
| 6 | PROG | passive | A resistor from PROG to VSS scales the preconditioning, fast charge and termination currents; letting PROG float disables the charge controller. |
| 7 | PG | output | Pseudo open-drain power good output that can sink but not source current, is low when the input is above UVLO and greater than the battery voltage, and should only be pulled up to the input. |
| 8 | THERM | input | Thermistor input with an internal 50 µA bias for 10 kΩ NTC thermistors, compared against typical factory thresholds of 1.20V and 0.25V. |
| 9 | VBAT | power_out | Battery charge control output connected to the battery positive terminal and the drain of the internal P-channel pass transistor; bypass to VSS with a minimum of 1 µF for loop stability when the battery is disconnected. |
| 10 | VBAT | power_out | Battery charge control output connected to the battery positive terminal and the drain of the internal P-channel pass transistor; bypass to VSS with a minimum of 1 µF for loop stability when the battery is disconnected. |
| 11 | EP | passive | Exposed thermal pad that is internally connected to the VSS pin and must be held at the same potential as VSS. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | DFN-10(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VDD | 3.75 | 6 | V | Charging | 3 | |
| Supply Voltage | VDD | 6 | V | Charge Complete, Standby | 3 | ||
| Supply Current | ISS | 2000 | 3000 | µA | Charging | 3 | |
| Supply Current | ISS | 150 | 300 | µA | Charge Complete | 3 | |
| Supply Current | ISS | 100 | 300 | µA | Standby (No Battery or PROG Floating) | 3 | |
| Supply Current | ISS | 50 | 100 | µA | Shutdown (VDD < VBAT, or VDD < VSTOP) | 3 | |
| UVLO Start Threshold | VSTART | 3.4 | 3.55 | 3.7 | V | VDD Low-to-High | 3 |
| UVLO Stop Threshold | VSTOP | 3.3 | 3.45 | 3.6 | V | VDD High-to-Low | 3 |
| Line Regulation | /(ΔVBAT/VBAT)/ΔVDD/ | 0.1 | 0.3 | %/V | VDD=[VREG(Typical)+1V] to 6V, IOUT=10 mA | 3 | |
| Load Regulation | /ΔVBAT/VBAT/ | 0.1 | 0.3 | % | IOUT=10 mA to 100 mA, VDD=[VREG(Typical)+1V] | 3 | |
| Fast Charge Current Regulation | IREG | 90 | 100 | 110 | mA | PROG = 10 kΩ | 3 |
| Fast Charge Current Regulation | IREG | 900 | 1000 | 1100 | mA | PROG = 1.0 kΩ | 3 |
| Output Reverse Leakage Current | IDISCHARGE | 0.15 | 2 | µA | PROG Floating | 4 | |
| Output Reverse Leakage Current | IDISCHARGE | 0.25 | 2 | µA | VDD < VBAT | 4 | |
| Output Reverse Leakage Current | IDISCHARGE | -5.5 | -15 | µA | Charge Complete | 4 | |
| Sink Current | ISINK | 15 | 25 | mA | 4 | ||
| Low Output Voltage | VOL | 0.4 | 1 | V | ISINK = 4 mA | 4 | |
| Input Leakage Current | ILK | 0.01 | 1 | µA | High Impedance, 6V on pin | 4 | |
| Charge Impedance Range | RPROG | 1 | 20 | kΩ | 4 | ||
| Standby Impedance | RPROG | 70 | 200 | kΩ | Minimum Impedance for Standby | 4 | |
| Thermistor Current Source | ITHERM | 47 | 50 | 53 | µA | 2 kΩ < RTHERM < 50 kΩ | 4 |
| Upper Trip Threshold | VT1 | 1.2 | 1.23 | 1.26 | V | VTHERM Low-to-High | 4 |
| Lower Trip Threshold | VT2 | 0.235 | 0.25 | 0.265 | V | VTHERM High-to-Low | 4 |
| THERM Input Sink Current | ISINK | 3 | 6 | 20 | µA | Stand-by or system test mode | 4 |
| Bypass Capacitance | CBAT | 1 | µF | IOUT < 250 mA | 4 | ||
| Bypass Capacitance | CBAT | 4.7 | µF | IOUT > 250 mA | 4 | ||
| Timer Enable Input High Voltage Level | VIH | 2 | V | 5 | |||
| Timer Enable Input Low Voltage Level | VIL | 0.6 | V | 5 | |||
| Timer Enable Input Leakage Current | ILK | 0.01 | 1 | µA | VTE = 6V | 5 | |
| UVLO Start Delay | tSTART | 5 | ms | VDD Low-to-High | 5 | ||
| Transition Time Out of Preconditioning | tDELAY | 1 | ms | VBATVPTH | 5 | ||
| Current Rise Time Out of Preconditioning | tRISE | 1 | ms | IOUT Rising to 90% of IREG | 5 | ||
| Preconditioning Comparator Filter Time | tPRECON | 0.4 | 1.3 | 3.2 | ms | Average VBAT Rise/Fall | 5 |
| Termination Comparator Filter Time | tTERM | 0.4 | 1.3 | 3.2 | ms | Average IOUT Falling | 5 |
| Charge Comparator Filter Time | tCHARGE | 0.4 | 1.3 | 3.2 | ms | Average VBAT Falling | 5 |
| Thermistor Comparator Filter Time | tTHERM | 0.4 | 1.3 | 3.2 | ms | Average THERM Rise/Fall | 5 |
| Status Output turn-off | tOFF | 200 | µs | ISINK = 1 mA to 0 mA | 5 | ||
| Status Output turn-on | tON | 200 | µs | ISINK = 0 mA to 1 mA | 5 | ||
| Specified Temperature Range | TA | -40 | 85 | °C | 5 | ||
| Operating Temperature Range | TA | -40 | 125 | °C | 5 | ||
| Supply Voltage | VDD | 7 | V | 3 | |||
| All Inputs and Outputs | -0.3 | V | w.r.t. VSS; upper limit is (VDD+0.3)V | 3 | |||
| Storage Temperature Range | TA | -65 | 150 | °C | 5 | ||
| ESD Human Body Model | 4 | kV | Human Body Model (HBM) (1.5 kΩ in Series with 100 pF) | 3 | |||
| ESD Machine Model | 300 | V | Machine Model (MM) (200 pF, No Series Resistance) | 3 | |||
| Thermal Resistance, DFN-10, 3 mm x 3 mm | θJA | 41 | °C/W | 4-Layer JC51-7 Standard Board, Natural Convection | 5 |
CAD (KiCad official)
- Symbol:
MCP73833-BZI - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10(3x3) (KiCad packages3D, STEP)
- 3D model files:
mcp73833-bzi-etched.step/mcp73833-bzi-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp73833-bzi.step/mcp73833-bzi.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (32 pp, sha256
70b297a13b77cebf, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
Other parts in this family
This page is MCP73833-BZI/MF. These part numbers share its family name but are different parts (another package, rating or grade), each with its own page:
- MCP73833-BZI/UN
# MCP73833-BZI/MF
**Microchip Tech** · Battery Management ICs · DFN-10(3x3)
MCP73833-BZI from Microchip Tech, in a DFN-10(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VDD | power_in | Battery management input supply; a supply of [VREG (typical) + 0.3V] to 6V is recommended, bypassed to VSS with a minimum of 1 µF. |
| 2 | VDD | power_in | Battery management input supply; a supply of [VREG (typical) + 0.3V] to 6V is recommended, bypassed to VSS with a minimum of 1 µF. |
| 3 | STAT1 | output | Open-drain charge status output for an LED or a pull-up resistor to a host microcontroller. |
| 4 | STAT2 | output | Open-drain charge status output for an LED or a pull-up resistor to a host microcontroller. |
| 5 | VSS | power_in | Battery management 0V reference; connect to the negative terminal of the battery and the input supply. |
| 6 | PROG | passive | A resistor from PROG to VSS scales the preconditioning, fast charge and termination currents; letting PROG float disables the charge controller. |
| 7 | PG | output | Pseudo open-drain power good output that can sink but not source current, is low when the input is above UVLO and greater than the battery voltage, and should only be pulled up to the input. |
| 8 | THERM | input | Thermistor input with an internal 50 µA bias for 10 kΩ NTC thermistors, compared against typical factory thresholds of 1.20V and 0.25V. |
| 9 | VBAT | power_out | Battery charge control output connected to the battery positive terminal and the drain of the internal P-channel pass transistor; bypass to VSS with a minimum of 1 µF for loop stability when the battery is disconnected. |
| 10 | VBAT | power_out | Battery charge control output connected to the battery positive terminal and the drain of the internal P-channel pass transistor; bypass to VSS with a minimum of 1 µF for loop stability when the battery is disconnected. |
| 11 | EP | passive | Exposed thermal pad that is internally connected to the VSS pin and must be held at the same potential as VSS. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | DFN-10(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VDD | 3.75 | | 6 | V | Charging | 3 |
| Supply Voltage | VDD | | | 6 | V | Charge Complete, Standby | 3 |
| Supply Current | ISS | | 2000 | 3000 | µA | Charging | 3 |
| Supply Current | ISS | | 150 | 300 | µA | Charge Complete | 3 |
| Supply Current | ISS | | 100 | 300 | µA | Standby (No Battery or PROG Floating) | 3 |
| Supply Current | ISS | | 50 | 100 | µA | Shutdown (VDD < VBAT, or VDD < VSTOP) | 3 |
| UVLO Start Threshold | VSTART | 3.4 | 3.55 | 3.7 | V | VDD Low-to-High | 3 |
| UVLO Stop Threshold | VSTOP | 3.3 | 3.45 | 3.6 | V | VDD High-to-Low | 3 |
| Line Regulation | /(ΔVBAT/VBAT)/ΔVDD/ | | 0.1 | 0.3 | %/V | VDD=[VREG(Typical)+1V] to 6V, IOUT=10 mA | 3 |
| Load Regulation | /ΔVBAT/VBAT/ | | 0.1 | 0.3 | % | IOUT=10 mA to 100 mA, VDD=[VREG(Typical)+1V] | 3 |
| Fast Charge Current Regulation | IREG | 90 | 100 | 110 | mA | PROG = 10 kΩ | 3 |
| Fast Charge Current Regulation | IREG | 900 | 1000 | 1100 | mA | PROG = 1.0 kΩ | 3 |
| Output Reverse Leakage Current | IDISCHARGE | | 0.15 | 2 | µA | PROG Floating | 4 |
| Output Reverse Leakage Current | IDISCHARGE | | 0.25 | 2 | µA | VDD < VBAT | 4 |
| Output Reverse Leakage Current | IDISCHARGE | | -5.5 | -15 | µA | Charge Complete | 4 |
| Sink Current | ISINK | | 15 | 25 | mA | | 4 |
| Low Output Voltage | VOL | | 0.4 | 1 | V | ISINK = 4 mA | 4 |
| Input Leakage Current | ILK | | 0.01 | 1 | µA | High Impedance, 6V on pin | 4 |
| Charge Impedance Range | RPROG | 1 | | 20 | kΩ | | 4 |
| Standby Impedance | RPROG | 70 | | 200 | kΩ | Minimum Impedance for Standby | 4 |
| Thermistor Current Source | ITHERM | 47 | 50 | 53 | µA | 2 kΩ < RTHERM < 50 kΩ | 4 |
| Upper Trip Threshold | VT1 | 1.2 | 1.23 | 1.26 | V | VTHERM Low-to-High | 4 |
| Lower Trip Threshold | VT2 | 0.235 | 0.25 | 0.265 | V | VTHERM High-to-Low | 4 |
| THERM Input Sink Current | ISINK | 3 | 6 | 20 | µA | Stand-by or system test mode | 4 |
| Bypass Capacitance | CBAT | 1 | | | µF | IOUT < 250 mA | 4 |
| Bypass Capacitance | CBAT | 4.7 | | | µF | IOUT > 250 mA | 4 |
| Timer Enable Input High Voltage Level | VIH | 2 | | | V | | 5 |
| Timer Enable Input Low Voltage Level | VIL | | | 0.6 | V | | 5 |
| Timer Enable Input Leakage Current | ILK | | 0.01 | 1 | µA | VTE = 6V | 5 |
| UVLO Start Delay | tSTART | | | 5 | ms | VDD Low-to-High | 5 |
| Transition Time Out of Preconditioning | tDELAY | | | 1 | ms | VBAT<VPTH to VBAT>VPTH | 5 |
| Current Rise Time Out of Preconditioning | tRISE | | | 1 | ms | IOUT Rising to 90% of IREG | 5 |
| Preconditioning Comparator Filter Time | tPRECON | 0.4 | 1.3 | 3.2 | ms | Average VBAT Rise/Fall | 5 |
| Termination Comparator Filter Time | tTERM | 0.4 | 1.3 | 3.2 | ms | Average IOUT Falling | 5 |
| Charge Comparator Filter Time | tCHARGE | 0.4 | 1.3 | 3.2 | ms | Average VBAT Falling | 5 |
| Thermistor Comparator Filter Time | tTHERM | 0.4 | 1.3 | 3.2 | ms | Average THERM Rise/Fall | 5 |
| Status Output turn-off | tOFF | | | 200 | µs | ISINK = 1 mA to 0 mA | 5 |
| Status Output turn-on | tON | | | 200 | µs | ISINK = 0 mA to 1 mA | 5 |
| Specified Temperature Range | TA | -40 | | 85 | °C | | 5 |
| Operating Temperature Range | TA | -40 | | 125 | °C | | 5 |
| Supply Voltage | VDD | | | 7 | V | | 3 |
| All Inputs and Outputs | | -0.3 | | | V | w.r.t. VSS; upper limit is (VDD+0.3)V | 3 |
| Storage Temperature Range | TA | -65 | | 150 | °C | | 5 |
| ESD Human Body Model | | 4 | | | kV | Human Body Model (HBM) (1.5 kΩ in Series with 100 pF) | 3 |
| ESD Machine Model | | | | 300 | V | Machine Model (MM) (200 pF, No Series Resistance) | 3 |
| Thermal Resistance, DFN-10, 3 mm x 3 mm | θJA | | 41 | | °C/W | 4-Layer JC51-7 Standard Board, Natural Convection | 5 |
## CAD (KiCad official)
- Symbol: `MCP73833-BZI`
- Footprint: `Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm`
- 3D model: DFN-10(3x3) (KiCad packages3D, STEP)
- 3D model files: `mcp73833-bzi-etched.step` / `mcp73833-bzi-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mcp73833-bzi.step` / `mcp73833-bzi.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/mcp73833-bzi-datasheet.pdf) (32 pp, sha256 `70b297a13b77cebf`, retrieved 2026-11-02, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mcp73833-bzi-datasheet.pdf)
## Other parts in this family
This page is **MCP73833-BZI/MF**. These part numbers share its family name but are different parts (another package, rating or grade), each with its own page:
- MCP73833-BZI/UN