main
Ray Publish 0.1.0 08c1cc0

MCP73113T-06SI

Microchip Tech · Battery Management ICs · DFN-10-EP(3x3)

MCP73113T-06SI from Microchip Tech, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VDD power_in Battery management input supply: a supply of [VREG (Typical) + 0.3V] to 6.0V is recommended, bypass to VSS with a minimum of 1 µF, and the pin is rated 18V absolute maximum.
2 VDD power_in Battery management input supply: a supply of [VREG (Typical) + 0.3V] to 6.0V is recommended, bypass to VSS with a minimum of 1 µF, and the pin is rated 18V absolute maximum.
3 VBAT power_in Battery charge control output connected to the positive battery terminal; bypass to VSS with a minimum of 1 µF to ensure loop stability when the battery is disconnected.
4 VBAT power_in Battery charge control output connected to the positive battery terminal; bypass to VSS with a minimum of 1 µF to ensure loop stability when the battery is disconnected.
5 NC unconnected No connection.
6 NC unconnected No connection.
7 STAT output Open-drain charge status output for driving an LED in stand-alone use or a pull-up resistor to interface with a host microcontroller; Table 5-2 summarizes its state during a charge cycle.
8 VSS power_in Battery management 0V reference, connected to the negative battery terminal and the input supply.
9 VSS power_in Battery management 0V reference, connected to the negative battery terminal and the input supply.
10 PROG bidirectional Sets the fast charge current through a resistor to VSS in constant-current mode; rated up to 5V with 6V absolute maximum, and floating or an impedance above 200 k disables the charger.
11 EP passive Exposed thermal pad that should be connected to the PCB exposed copper area to enhance thermal power dissipation.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package DFN-10-EP(3x3)
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Voltage Range VDD 4 16 V 5
Operating Supply Voltage VDD 4.2 6.5 V 5
Supply Current, Shutdown ISS 4 5.5 µA Shutdown (VDD < VBAT - 150 mV) 5
Supply Current, Charging ISS 700 1500 µA Charging 5
Supply Current, Standby ISS 30 100 µA Standby (PROG Floating) 5
Supply Current, Charge Complete; No Battery ISS 50 150 µA Charge Complete; No Battery; VDD < VSTOP 5
Battery Discharge Current, Standby IDISCHARGE 0.5 2 µA Standby (PROG Floating) 5
Output Reverse Leakage Current, Shutdown IDISCHARGE 0.5 2 µA Shutdown (VDD < VBAT, or VDD < VSTOP) 5
Output Reverse Leakage Current, Charge Complete; VDD present IDISCHARGE 6 17 µA Charge Complete; VDD is present 5
UVLO Start Threshold VSTART 4.1 4.15 4.25 V 5
UVLO Stop Threshold VSTOP 4 4.05 4.15 V 5
OVP Start Threshold (MCP73113) VOVP 6.4 6.5 6.6 V MCP73113 5
Regulated Output Voltage (4.20V option) VREG 4.179 4.2 4.221 V VDD = [VREG(Typical)+1V] 5
Output Voltage Tolerance VRTOL -0.5 0.5 % 5
Line Regulation 0.05 0.2 %/V VDD = [VREG(Typical)+1V] to 6V; IOUT = 50 mA 5
Load Regulation 0.05 0.2 % IOUT = 50 mA - 150 mA; VDD = [VREG(Typical)+1V] 5
VPROG Absolute Maximum VPROG 6 V 5
All Inputs and Outputs w.r.t. VSS (minimum) -0.3 V 5
Fast Charge Current Regulation IREG 130 1100 mA TA = -5°C to +55°C 6
Precondition Current Ratio IPREG / IREG 8 10 15 % PROG = 1 kto 10 k, TA = -5°C to +55°C 6
Precondition Voltage Threshold Ratio (71.5% option) VPTH / VREG 69 71.5 74 % VBAT Low-to-High 6
Charge Termination Current Ratio (10% option) ITERM / IREG 7.5 10 12.5 % 6
Automatic Recharge Voltage Threshold Ratio (95% option) VRTH / VREG 93 95 97 % VBAT High-to-Low 6
Sink Current (STAT) ISINK 20 35 mA 6
Low Output Voltage (STAT) VOL 0.2 0.5 V ISINK = 4 mA 6
Input Leakage Current (STAT) ILK 0.001 1 A High-Impedance, VDD on pin 6
Charge Impedance Range (PROG) RPROG 1 21 k 6
Shutdown Impedance (PROG) RPROG 70 200 k Impedance for Shutdown 6
PROG Voltage Range VPROG 0 5 V 6
Elapsed Timer Period (6 HR option) tELAPSED 5.4 6 6.6 Hours 7
Preconditioning Timer Period (32 min option) tPRECHG 0.4 0.5 0.6 Hours 7
Status Output Turn-off Delay tOFF 500 µs ISINK = 1 mA to 0 mA 7
Status Output Turn-on Delay tON 500 µs ISINK = 0 mA to 1 mA 7
Specified Temperature Range TA -40 85 °C 7
Operating Temperature Range TJ -40 125 °C 7
Storage Temperature Range TA -65 150 °C 7
Thermal Resistance, DFN-10 (3x3) junction-to-ambient JA 64 °C/W 4-Layer JC51-7 Standard Board, Natural Convection 7
Thermal Resistance, DFN-10 (3x3) junction-to-case JC 12 °C/W 7

CAD (KiCad official)

  • Symbol: MCP73113T-06SI
  • Footprint: Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm
  • 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: mcp73113t-06si-etched.step / mcp73113t-06si-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp73113t-06si.step / mcp73113t-06si.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (34 pp, sha256 681afd857c2b10d4, retrieved 2026-10-29, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF