MCP6V86UT-E from Microchip Tech, in a SC-70-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin	Name	Type	Function
1	VIN+	power_in	Noninverting input, a high-impedance CMOS input with low bias current, to be kept between VSS and VDD for normal operation.
2	VSS	power_in	Negative power supply, normally tied to ground in single-supply use; VDD must be 2.2V to 5.5V higher than VSS.
3	VIN-	power_in	Inverting input, a high-impedance CMOS input with low bias current, to be kept between VSS and VDD for normal operation.
4	VOUT	output	Op amp output, a low-impedance voltage source.
5	VDD	power_in	Positive power supply, 2.2V to 5.5V above VSS, and it needs bypass capacitors.

Key specifications

Parameter	Value
Manufacturer	Microchip Tech
Package	SC-70-5
Category	Operational Amplifier/Comparator
Pins	5

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter	Symbol	Min	Typ	Max	Unit	Conditions	Page
Input Offset Voltage	VOS	-25		25	µV	TA = +25°C	3
Input Offset Voltage Drift (linear TC)	TC1	-150		150	nV/°C	TA = -40 to +125°C, Note 1 (design guidance only; not tested)	3
Power Supply Rejection Ratio	PSRR	110	127		dB		3
Input Bias Current	IB	-50	2	50	pA		4
Input Bias Current Across Temperature	IB	0	0.24	1	nA	TA = +125°C	4
Input Offset Current	IOS	-400	100	400	pA		4
Input Offset Current Across Temperature	IOS	-500	100	500	pA	TA = +125°C	4
Common-Mode Input Voltage Range Low	VCML			-0.2	V	printed as VSS, 0.2 V	4
Common-Mode Input Voltage Range High	VCMH	0.3			V	printed as VDD + 0.3	4
Common-Mode Rejection Ratio	CMRR	103	128		dB	VDD = 2.2V, VCM = -0.2V to 2.5V	4
Common-Mode Rejection Ratio	CMRR	112	136		dB	VDD = 5.5V, VCM = -0.2V to 5.8V	4
DC Open-Loop Gain	AOL	97	146		dB	VDD = 2.2V, VOUT = 0.3V to 2.0V	4
DC Open-Loop Gain	AOL	111	151		dB	VDD = 5.5V, VOUT = 0.3V to 5.3V	4
Minimum Output Voltage Swing	VOL	0	35	120	mV	RL = 1kΩ, G = +2, 0.5V input overdrive; printed as VSS, VSS + 35, VSS + 120	4
Maximum Output Voltage Swing	VOH	-120	-45	0	mV	RL = 1kΩ, G = +2, 0.5V input overdrive; printed as VDD, 120, VDD, 45, VDD	4
Supply Voltage	VDD	2.2		5.5	V		4
Quiescent Current per Amplifier	IQ	250	500	770	µA	IO = 0	4
Power-on Reset Trip Voltage	VPOR	1.2	1.6	1.9	V		4
Specified Temperature Range	TA	-40		125	°C		5
Operating Temperature Range	TA	-40		125	°C	Note 1: TJ must not exceed +150°C	5
Current at Input Pins		-2		2	mA	printed ±2 mA	3
Analog Input Voltage (VIN+, VIN-)		-1		1	V	printed VSS, 1.0V to VDD + 1.0V	3
All Other Inputs and Outputs		-0.3		0.3	V	printed VSS, 0.3V to VDD + 0.3V	3
Current at Output and Supply Pins		-30		30	mA	printed ±30 mA	3
Storage Temperature		-65		150	°C		3
Maximum Junction Temperature	TJ			150	°C		3
Storage Temperature Range	TA	-65		150	°C		5
Thermal Resistance, 5-Lead SC70	θJA		209		°C/W		5
Input Offset Voltage Quadratic Temperature Coefficient	TC2		30		pV/°C2	TA = -40°C to +125°C; printed ±30	3
Input Offset Voltage Aging	∆VOS		0.25		µV	408 hours Life Test at +150°C, measured at +25°C; printed ±0.25	3
Output Short-Circuit Current	ISC		15		mA	VDD = 2.2V; printed ±15	4
Output Short-Circuit Current	ISC		40		mA	VDD = 5.5V; printed ±40	4
Gain Bandwidth Product	GBWP		5		MHz		5
Slew Rate	SR		4		V/µs		5
Phase Margin	PM		60		°C	G = +1	5
Input Noise Voltage	Eni		0.28		µVP-P	f = 0.1 Hz to 10 Hz	5
Input Noise Voltage Density	eni		13		nV/√Hz	f < 2 kHz	5
Start-up Time	tSTR		100		µs	G = +1, 0.1% VOUT settling (Note 2)	5

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part	Material	Colour / plating	Datasheet says	Page
contacts		gold	14-Lead *Y = Nickel palladium gold manufacturing designator.	49

CAD (KiCad official)

Symbol: MCP6V86UT-E
Footprint: Package_TO_SOT_SMD:SOT-353_SC-70-5
3D model: SC-70-5 (KiCad packages3D, STEP)
3D model files: mcp6v86ut-e-etched.step / mcp6v86ut-e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp6v86ut-e.step / mcp6v86ut-e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

Datasheet: Microchip Tech datasheet (52 pp, sha256 201ddce8232c3062, retrieved 2026-10-31, tier: manufacturer)
Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF

MCP6V86UT-E

Verified MCP6V86UT-E

Verification log 1 record

3D Model

Symbol & Footprint

Schematic Symbol

PCB Footprint

Datasheet

README