main
Ray Publish 0.1.0 70d0152

MCP65R46T-2402E

Microchip Tech · Comparators · SOT-23-6

MCP65R46T-2402E from Microchip Tech, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol and footprint from KiCad-official CAD; the 3D model is generated from the datasheet's package dimensions.

Pinout

Pin Name Type Function
1 OUT output Digital open-drain output of the MCP65R46, which requires an external pull-up resistor and can level-shift from 1.6V to 10V or be used in wired-OR logic.
2 VSS power_in Negative power supply (ground); VDD must be 1.8V to 5.5V higher than VSS.
3 VIN+ power_in Noninverting comparator input, a high-impedance CMOS input with low bias current and rail-to-rail range from VSS - 0.3V to VDD + 0.3V.
4 VIN- power_in Inverting comparator input, a high-impedance CMOS input with low bias current and rail-to-rail range from VSS - 0.3V to VDD + 0.3V.
5 VREF power_in Reference voltage output of 2.4V for the MCP65R46T-2402E variant (factory set, ±1% typical).
6 VDD power_in Positive power supply from 1.8V to 5.5V, needing a local 0.01 µF to 0.1 µF bypass capacitor within 2 mm of the pin.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOT-23-6
Category Operational Amplifier/Comparator
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VDD 1.8 5.5 V 3
Quiescent Current per Comparator IQ 2.5 4 µA IOUT = 0 3
Input Voltage Range VCMR -0.3 V VSS-0.3 to VDD+0.3 3
Common-Mode Rejection Ratio CMRR 55 70 dB VDD = 5V, VCM = -0.3V to 5.3V 3
Common-Mode Rejection Ratio CMRR 50 65 dB VDD = 5V, VCM = 2.5V to 5.3V 3
Common-Mode Rejection Ratio (MCP65R46) CMRR 50 70 dB VDD = 5V, MCP65R46, VCM = -0.3V to 2.5V 3
Power Supply Rejection Ratio PSRR 63 80 dB VCM = VSS 3
Input Offset Voltage VOS -10 3 10 mV VCM = VSS (Note 1) 3
Input Hysteresis Voltage VHYST 1 3.3 5 mV VCM = VSS (Note 1) 3
Input Bias Current IB 5000 pA TA = +125°C, VCM = VSS 3
Low-Level Output Voltage (Open Drain) VOL 0.2 V VSS+0.2 max; IOUT = 2 mA, VDD = 5.5V 4
High-Level Output Current (Open Drain) IOH -100 nA VPU = 10V 4
Pull-Up Voltage VPU 1.6 10 V Note 3 4
Initial Reference Tolerance VTOL -2 1 2 % IREF = 0A, VREF = 1.21V and 2.4V 4
Reference Voltage (2.4V) VREF 2.352 2.4 2.448 V IREF = 0A 4
Reference VREF Drift with Temperature VREF/T 23 100 ppm VREF = 2.4V, VDD = 5.5V 4
Propagation Delay (High-to-Low) tPHL 4 8 µs Step = 200 mV, Overdrive = 100 mV, CL = 50 pF 5
Propagation Delay (Low-to-High) tPLH 4 8 µs Step = 200 mV, Overdrive = 100 mV, CL = 50 pF 5
Specified Temperature Range TA -40 125 °C 5
Operating Temperature Range TA -40 125 °C 5
Storage Temperature Range TA -65 150 °C 5
Supply Voltage VDD - VSS VDD - VSS 7 V 3
All other inputs and outputs -0.3 0.3 V VSS, 0.3V to VDD + 0.3V 3
Output Short Circuit Current -25 25 mA 3
Current at Input Pins -2 2 mA 3
Current at Output and Supply Pins -50 50 mA 3
Storage temperature -65 150 °C 3
Ambient temperature with power applied -40 125 °C 3
Junction temperature 150 °C 3
Thermal Resistance, SOT23-6 θJA 190.5 °C/W 5
Input Offset Voltage Drift with Temperature VOS/T 10 µV/°C VCM = VSS 3
Short Circuit Current (Open Drain) ISC 50 mA VPU = VDD = 5.5V (±50 printed) 4
Reference Output Current IREF 500 µA VTOL = ±2% (maximum) (±500 printed) 4
Maximum Toggle Frequency fMAX 120 kHz VDD = 5.5V 5

CAD (land: KiCad; 3D: generated from the datasheet)

  • Symbol: MCP65R46T-2402E
  • Footprint: Package_TO_SOT_SMD:SOT-23-6
  • 3D model: SOT-23-6, generated on the KiCad land (body 1.6 x 2.9 mm, terminals on the pads, 1.175 mm tall, datasheet A, midpoint of min and max). KiCad's stock model for this land is taller than the datasheet allows, so the model is generated from the datasheet drawing; the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
  • 3D model files: mcp65r46t-2402e-chy-etched.step / mcp65r46t-2402e-chy-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp65r46t-2402e-chy.step / mcp65r46t-2402e-chy.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (36 pp, sha256 3296c4e9fe54dddc, retrieved 2026-11-16, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-opus-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: land: KiCad official libraries (CC-BY-SA 4.0); 3D: generated from the datasheet's package dimensions (provenance.model_3d_generated).

Datasheet PDF