Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MCP48FVB04-E

Microchip Tech · Digital To Analog Converters (DACs) · VQFN-20-EP(5x5)

MCP48FVB04-E from Microchip Tech, in a VQFN-20-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CS input SPI chip select pin (Schmitt trigger input) that enables/disables the serial interface so SPI commands can be received.
2 VREF0 bidirectional Analog voltage reference input 0 for even channels (0-6); an input when VREF pin is the reference and an output with minimal drive when the internal band gap is selected.
3 VOUT0 output Buffered analog voltage output of channel 0, with about 1 ohm DC output impedance in Normal mode.
4 VOUT2 output Buffered analog voltage output of channel 2, with about 1 ohm DC output impedance in Normal mode.
5 NC unconnected Not internally connected.
6 NC unconnected Not internally connected.
7 VSS power_in Ground reference pin for all circuitry on the device; connect to a ground plane through a low-impedance connection.
8 NC unconnected Not internally connected.
9 NC unconnected Not internally connected.
10 NC unconnected Not internally connected.
11 NC unconnected Not internally connected.
12 VOUT3 output Buffered analog voltage output of channel 3, with about 1 ohm DC output impedance in Normal mode.
13 VOUT1 output Buffered analog voltage output of channel 1, with about 1 ohm DC output impedance in Normal mode.
14 VREF1 bidirectional Analog voltage reference input 1 for odd channels (1-7); an input when VREF pin is the reference and an output with minimal drive when the internal band gap is selected.
15 SDO output SPI serial data output pin.
16 SCK input SPI serial clock pin (Schmitt trigger input).
17 SDI input SPI serial data input pin (Schmitt trigger input).
18 LAT0/HVC input DAC register latch 0 for DAC0/DAC2 (low transfers volatile registers to outputs) and High-Voltage Command pin that allows user Configuration bits to be written when above the VIHH entry voltage.
19 LAT1 input DAC register latch 1 pin that transfers the volatile DAC1/DAC3 register values (wiper and Configuration bits) to VOUT1 and VOUT3 when low.
20 VDD power_in Positive supply voltage pin, 2.7V to 5.5V for full specifications; bypass with about 0.1 µF ceramic to ground (plus 10 µF tantalum recommended).
21 EP passive Exposed thermal pad pin.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package VQFN-20-EP(5x5)
Category Data Converters
Pins 21

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage (full specs) VDD 2.7 5.5 V 6
Supply Voltage (reduced specs) VDD 1.8 2.7 V Serial interface operational, DAC operation with reduced analog specifications 6
Operating Temperature TA -40 125 °C Extended 6
VDD voltage to ensure POR VPOR/BOR 1.7 V RAM retention voltage: (VRAM) < VPOR 6
HV command voltage range VHV 0 12.5 V HVC pin 6
High-Voltage Input Entry Voltage VIHHEN 9 V Threshold for entry into WiperLock technology 6
Supply Current Quad 1 MHz IDD 1 mA Quad, serial interface active, VDD = 5.5V, 1 MHz, VOUT unloaded, midscale 7
Supply Current Quad 10 MHz IDD 1.7 mA Quad, 10 MHz, VDD = 5.5V 7
Supply Current Quad 20 MHz IDD 2.6 mA Quad, 20 MHz, VDD = 5.5V 7
Supply Current Quad, interface inactive IDD 0.85 mA Quad, SCK = SDI = VSS, VOUT unloaded, midscale 7
Quad HV command current IDD 560 700 µA Quad, HVC = 12.5V, serial interface inactive, VREF = VDD = 5.5V 7
Power-Down Current IDDP 0.68 3.8 µA PDnB:PDnA = 01, VOUT not connected 7
Resistor Ladder Resistance RL 100 140 180 kΩ VRnB:VRnA = 10, VREF = VDD 8
Nominal VOUT Match /VOUT-VOUTMEAN//VOUTMEAN 0.5 1 % 2.7V ≤ VDD ≤ 5.5V 8
Nominal VOUT Match (1.8V) /VOUT-VOUTMEAN//VOUTMEAN 1.2 % 1.8V 8
VOUT Temperature Coefficient ΔVOUT/ΔT 15 ppm/°C Code = Midscale 8
VREF Pin Input Voltage Range VREF 0 5.5 V 1.8V ≤ VDD ≤ 5.5V; VSS to VDD 8
Zero-Scale Error 8-bit EZS 0.75 LSb 8-bit VRnB:VRnA = 10, Gx = 0, VREF = VDD, no load 9
Full-Scale Error 8-bit EFS 4.5 LSb 8-bit VRnB:VRnA = 10, Gx = 0, VREF = VDD, no load 9
Offset Error EOS -15 1.5 15 mV VRnB:VRnA = 00, Gx = 0, no load 9
Offset Voltage Temperature Coefficient VOSTC 10 µV/°C 9
Gain Error 8-bit EG -1 0.1 1 % of FSR 8-bit Code = 250, no load, VRnB:VRnA = 00, Gx = 0 10
Gain Error Drift ΔG/°C -3 ppm/°C 10
Total Unadjusted Error 8-bit ET -2.5 0.5 LSb 8-bit VRnB:VRnA = 10, Gx = 0, VREF = VDD, no load 10
Integral Nonlinearity 8-bit INL -0.5 0.1 0.5 LSb 8-bit VRnB:VRnA = 10, Gx = 0, VREF = VDD, no load 11
Differential Nonlinearity 8-bit DNL -0.25 0.0125 0.25 LSb 8-bit VRnB:VRnA = 10, Gx = 0, VREF = VDD, no load 12
Short-Circuit Current to VSS ISC 3 9 22 mA Short to VSS DAC Code = Full Scale 13
Short-Circuit Current to VDD ISC 3 9 22 mA Short to VDD DAC Code = 000h 13
Band Gap Voltage VBG 1.18 1.22 1.26 V 13
Band Gap Operating Range (VREF stable) VDD 2 5.5 V VREF pin voltage stable 13
Band Gap Operating Range (VOUT linear) VDD 2.2 5.5 V VOUT output linear 13
VREF Input Range Buffered VREF 0 V VRnB:VRnA = 11 (Buffered mode), upper limit VDD, 0.04 13
Schmitt Trigger High Input Threshold VIH 0.45 V 2.7V ≤ VDD ≤ 5.5V, 0.45 VDD 14
Schmitt Trigger Low Input Threshold VIL 0.2 V 0.2 VDD 14
Output Low Voltage VOL 0 0.3 V IOL = 5 mA, VDD = 5.5V; max 0.3 VDD 14
Output High Voltage VOH 0.7 V IOH = -2.5 mA, VDD = 5.5V; min 0.7 VDD 14
Input Leakage Current IIL -1 1 µA VIN = VDD and VIN = VSS 14
EEPROM Programming Write Cycle Time tWC 11 16 ms VDD = +1.8V to 5.5V 15
Power Supply Sensitivity 8-bit PSS 0.002 0.005 %/% 8-bit Code = 7Fh 15
VOUT Settling Time tS 7.8 µs 12-bit Code = 400h to C00h; C00h to 400h 17
LATx Pin Pulse Width tLAT 20 ns 17
Voltage on VDD with respect to VSS VDD -0.6 6.5 V 5
Voltage on All Pins with respect to VSS -0.6 V Max VDD+0.3V 5
Input Clamp Current IIK -20 20 mA 5
Output Clamp Current IOK -20 20 mA VO < 0 or VO > VDD 5
Max Current out of VSS (Quad) 150 mA 5
Max Current into VDD (Quad) 150 mA 5
Max Current Sourced by VOUT 20 mA 5
Max Current Sunk by VOUT 20 mA 5
Max Current Sunk by VREF 125 µA 5
Max Input Current SDI, SCK, CS 2 mA 5
Max Output Current Sunk by SDO 25 mA 5
Total Power Dissipation 400 mW 5
Storage Temperature -65 150 °C 5
Ambient Temperature with Power Applied -55 125 °C 5
Maximum Junction Temperature TJ 150 °C 5

CAD (KiCad official)

  • Symbol: MCP48FVB04-E
  • Footprint: Package_DFN_QFN:QFN-20-1EP_5x5mm_P0.65mm_EP3.35x3.35mm
  • 3D model: VQFN-20-EP(5x5) (KiCad packages3D, STEP)
  • 3D model files: mcp48fvb04-e-etched.step / mcp48fvb04-e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp48fvb04-e.step / mcp48fvb04-e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (112 pp, sha256 c303d509852552ae, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF