main
Ray
Publish 0.1.0
61fd7df
MCP45HV51-503E
Microchip Tech · Pre-ordered MCUs · TSSOP-14
MCP45HV51-503E from Microchip Tech, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VL | power_in | Positive digital power supply input, ranging from 1.8V to 5.5V relative to DGND, with a decoupling capacitor on VL to DGND recommended. |
| 2 | SCL | input | I2C serial clock input; the device is an I2C slave so SCL is input-only with a Schmitt trigger. |
| 3 | A1 | input | I2C address bit 1 input that, together with A0, completes the device address and allows up to four devices on one bus. |
| 4 | SDA | bidirectional | I2C serial data pin, an open-drain N-channel driver with Schmitt-trigger input that lets the host read and write the Wiper and TCON registers. |
| 5 | A0 | input | I2C address bit 0 input whose value is latched at POR/BOR, completing the device address together with A1. |
| 6 | WLAT | input | Wiper latch enable; when Low the received I2C value is transferred to the Wiper register, and when High it is held in the I2C shift register buffer (SPBUF). |
| 7 | NC | unconnected | Pin not internally connected to the die; to reduce noise coupling, connect it to either DGND or VL. |
| 8 | SHDN | input | Shutdown input that forces the resistor network terminals into the hardware shutdown state. |
| 9 | DGND | power_in | Digital ground reference for the device logic and the VL supply. |
| 10 | V- | power_in | Analog negative potential supply; its potential must be lower than or equal to the DGND pin potential. |
| 11 | P0B | passive | Potentiometer 0 Terminal B; voltage must be between V- and V+, and it can carry both positive and negative current. |
| 12 | P0W | passive | Potentiometer 0 wiper terminal; voltage must be between V- and V+, and it can carry both positive and negative current. |
| 13 | P0A | passive | Potentiometer 0 Terminal A; voltage must be between V- and V+, and it can carry both positive and negative current. |
| 14 | V+ | power_in | Analog positive supply, which must be at a higher potential than V-; analog operation is specified from 10V to 36V relative to V-. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TSSOP-14 |
| Category | Embedded Processors & Controllers |
| Pins | 14 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Resistance tolerance (RAB) | RAB | -20 | 20 | % | Resistance (± 20%), -503 device | 4 | |
| End-to-end resistance | RAB | 40 | 50 | 60 | k | -503 devices, V+/V- = 10V to 36V | 4 |
| RAB current | IAB | 0.9 | mA | -503 devices, 36V / RAB(MIN), V- = -18V, V+ = +18V | 4 | ||
| Wiper resistance | RW | 75 | 170 | ohm | IW = 1 mA V+ = +18V, V- = -18V, code = 00h, PxA = floating, PxB = V-. | 6 | |
| Wiper resistance | RW | 145 | 200 | ohm | IW = 1 mA V+ = +5.0V, V- = -5.0V, code = 00h, PxA = floating, PxB = V-. (Note 2) | 6 | |
| Terminal current (A, B, W) | IT, IW | 6.5 | mA | -503 devices IBW(W ≠ ZS) and IAW(W ≠ FS) | 6 | ||
| Terminal current at zero/full scale | IT, IW | 36 | mA | IBW(W = ZS), or IAW(W = FS) | 6 | ||
| Supply current, serial interface active | IDDD | 45 | 650 | µA | Serial Interface Active, Write all 0's to Volatile Wiper 0 (address 0h), VL = 5.5V, FSCL = 3.4 MHz, V- = DGND | 5 | |
| Supply current, serial interface inactive | IDDD | 4 | 7 | µA | Serial Interface Inactive, VL = 5.5V, SCL = VIH, Wiper = 0, V- = DGND | 5 | |
| Supply current, analog | IDDA | 5 | µA | Current V+ to V-, PxA = PxB = PxW, DGND = V- +(V+/2) | 5 | ||
| Digital positive supply voltage | VL | 2.7 | 5.5 | V | With respect to DGND (Note 4) | 4 | |
| Digital positive supply voltage | VL | 1.8 | 5.5 | V | VL ≥ V- + 2.7V (Note 1, Note 4) | 4 | |
| Analog positive supply voltage | V+ | 36 | V | With respect to V- (Note 4) | 4 | ||
| Delay after device exits reset state | TBORD | 10 | 20 | µs | VL > VBOR | 5 | |
| Power supply sensitivity | PSS | 0.0015 | 0.0035 | %/% | 8-bit VL = 2.7V to 5.5V, V+ = 18V, V- = -18V, Code = 7Fh | 14 | |
| RAB current into PxA/PxB/PxW pins (continuous, 50 k) | -6.5 | 6.5 | mA | RAB = 50 k | 3 | ||
| Voltage on V+ with respect to DGND | V+ | -0.3 | 40 | V | Printed as DGND - 0.3V to 40.0V | 3 | |
| ESD protection, Human Body Model | -5 | 5 | kV | HBM | 3 | ||
| Maximum junction temperature | TJ | 150 | °C | 3 | |||
| Package power dissipation, TSSOP-14 | 1000 | mW | TA = +50°C, TJ = +150°C | 3 | |||
| Ambient temperature with power applied | TA | -40 | 125 | °C | 3 | ||
| Storage temperature | TA | -65 | 150 | °C | 3 | ||
| Thermal resistance, 14L-TSSOP (ST) | θJA | 100 | °C/W | 21 | |||
| Nominal resistance tempco | RAB/T | 50 | ppm/°C | TA = -40°C to +85°C | 6 | ||
| Nominal resistance tempco | RAB/T | 100 | ppm/°C | TA = -40°C to +125°C | 6 | ||
| Ratiometric tempco | VBW/T | 15 | ppm/°C | Code = Mid scale (7Fh or 3Fh) | 6 | ||
| Leakage current into A, W or B | ITL | 5 | nA | A = W = B = V- | 6 | ||
| Capacitance (PW) | CW | 120 | pF | Measured to V-, f = 1 MHz, Wiper code = Mid Scale | 13 | ||
| VW settling time (50 k) | tS | 2.5 | µs | VA = 10V, VB = 0V, ±1LSb error band, CL = 50 pF, Code = 00h -> FFh (7Fh); FFh (7Fh) -> 00h | 10 |
CAD (KiCad official)
- Symbol:
MCP45HV51-503E - Footprint:
Package_SO:TSSOP-14_4.4x5mm_P0.65mm - 3D model: TSSOP-14 (KiCad packages3D, STEP)
- 3D model files:
mcp45hv51-503e-etched.step/mcp45hv51-503e-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp45hv51-503e.step/mcp45hv51-503e.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (100 pp, sha256
ab854db7c83242c1, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MCP45HV51-503E
**Microchip Tech** · Pre-ordered MCUs · TSSOP-14
MCP45HV51-503E from Microchip Tech, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VL | power_in | Positive digital power supply input, ranging from 1.8V to 5.5V relative to DGND, with a decoupling capacitor on VL to DGND recommended. |
| 2 | SCL | input | I2C serial clock input; the device is an I2C slave so SCL is input-only with a Schmitt trigger. |
| 3 | A1 | input | I2C address bit 1 input that, together with A0, completes the device address and allows up to four devices on one bus. |
| 4 | SDA | bidirectional | I2C serial data pin, an open-drain N-channel driver with Schmitt-trigger input that lets the host read and write the Wiper and TCON registers. |
| 5 | A0 | input | I2C address bit 0 input whose value is latched at POR/BOR, completing the device address together with A1. |
| 6 | WLAT | input | Wiper latch enable; when Low the received I2C value is transferred to the Wiper register, and when High it is held in the I2C shift register buffer (SPBUF). |
| 7 | NC | unconnected | Pin not internally connected to the die; to reduce noise coupling, connect it to either DGND or VL. |
| 8 | SHDN | input | Shutdown input that forces the resistor network terminals into the hardware shutdown state. |
| 9 | DGND | power_in | Digital ground reference for the device logic and the VL supply. |
| 10 | V- | power_in | Analog negative potential supply; its potential must be lower than or equal to the DGND pin potential. |
| 11 | P0B | passive | Potentiometer 0 Terminal B; voltage must be between V- and V+, and it can carry both positive and negative current. |
| 12 | P0W | passive | Potentiometer 0 wiper terminal; voltage must be between V- and V+, and it can carry both positive and negative current. |
| 13 | P0A | passive | Potentiometer 0 Terminal A; voltage must be between V- and V+, and it can carry both positive and negative current. |
| 14 | V+ | power_in | Analog positive supply, which must be at a higher potential than V-; analog operation is specified from 10V to 36V relative to V-. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | TSSOP-14 |
| Category | Embedded Processors & Controllers |
| Pins | 14 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Resistance tolerance (RAB) | RAB | -20 | | 20 | % | Resistance (± 20%), -503 device | 4 |
| End-to-end resistance | RAB | 40 | 50 | 60 | k | -503 devices, V+/V- = 10V to 36V | 4 |
| RAB current | IAB | | | 0.9 | mA | -503 devices, 36V / RAB(MIN), V- = -18V, V+ = +18V | 4 |
| Wiper resistance | RW | | 75 | 170 | ohm | IW = 1 mA V+ = +18V, V- = -18V, code = 00h, PxA = floating, PxB = V-. | 6 |
| Wiper resistance | RW | | 145 | 200 | ohm | IW = 1 mA V+ = +5.0V, V- = -5.0V, code = 00h, PxA = floating, PxB = V-. (Note 2) | 6 |
| Terminal current (A, B, W) | IT, IW | | | 6.5 | mA | -503 devices IBW(W ≠ ZS) and IAW(W ≠ FS) | 6 |
| Terminal current at zero/full scale | IT, IW | | | 36 | mA | IBW(W = ZS), or IAW(W = FS) | 6 |
| Supply current, serial interface active | IDDD | | 45 | 650 | µA | Serial Interface Active, Write all 0's to Volatile Wiper 0 (address 0h), VL = 5.5V, FSCL = 3.4 MHz, V- = DGND | 5 |
| Supply current, serial interface inactive | IDDD | | 4 | 7 | µA | Serial Interface Inactive, VL = 5.5V, SCL = VIH, Wiper = 0, V- = DGND | 5 |
| Supply current, analog | IDDA | | | 5 | µA | Current V+ to V-, PxA = PxB = PxW, DGND = V- +(V+/2) | 5 |
| Digital positive supply voltage | VL | 2.7 | | 5.5 | V | With respect to DGND (Note 4) | 4 |
| Digital positive supply voltage | VL | 1.8 | | 5.5 | V | VL ≥ V- + 2.7V (Note 1, Note 4) | 4 |
| Analog positive supply voltage | V+ | | | 36 | V | With respect to V- (Note 4) | 4 |
| Delay after device exits reset state | TBORD | | 10 | 20 | µs | VL > VBOR | 5 |
| Power supply sensitivity | PSS | | 0.0015 | 0.0035 | %/% | 8-bit VL = 2.7V to 5.5V, V+ = 18V, V- = -18V, Code = 7Fh | 14 |
| RAB current into PxA/PxB/PxW pins (continuous, 50 k) | | -6.5 | | 6.5 | mA | RAB = 50 k | 3 |
| Voltage on V+ with respect to DGND | V+ | -0.3 | | 40 | V | Printed as DGND - 0.3V to 40.0V | 3 |
| ESD protection, Human Body Model | | -5 | | 5 | kV | HBM | 3 |
| Maximum junction temperature | TJ | | | 150 | °C | | 3 |
| Package power dissipation, TSSOP-14 | | | | 1000 | mW | TA = +50°C, TJ = +150°C | 3 |
| Ambient temperature with power applied | TA | -40 | | 125 | °C | | 3 |
| Storage temperature | TA | -65 | | 150 | °C | | 3 |
| Thermal resistance, 14L-TSSOP (ST) | θJA | | 100 | | °C/W | | 21 |
| Nominal resistance tempco | RAB/T | | 50 | | ppm/°C | TA = -40°C to +85°C | 6 |
| Nominal resistance tempco | RAB/T | | 100 | | ppm/°C | TA = -40°C to +125°C | 6 |
| Ratiometric tempco | VBW/T | | 15 | | ppm/°C | Code = Mid scale (7Fh or 3Fh) | 6 |
| Leakage current into A, W or B | ITL | | 5 | | nA | A = W = B = V- | 6 |
| Capacitance (PW) | CW | | 120 | | pF | Measured to V-, f = 1 MHz, Wiper code = Mid Scale | 13 |
| VW settling time (50 k) | tS | | 2.5 | | µs | VA = 10V, VB = 0V, ±1LSb error band, CL = 50 pF, Code = 00h -> FFh (7Fh); FFh (7Fh) -> 00h | 10 |
## CAD (KiCad official)
- Symbol: `MCP45HV51-503E`
- Footprint: `Package_SO:TSSOP-14_4.4x5mm_P0.65mm`
- 3D model: TSSOP-14 (KiCad packages3D, STEP)
- 3D model files: `mcp45hv51-503e-etched.step` / `mcp45hv51-503e-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mcp45hv51-503e.step` / `mcp45hv51-503e.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/mcp45hv51-503e-datasheet.pdf) (100 pp, sha256 `ab854db7c83242c1`, retrieved 2026-10-28, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mcp45hv51-503e-datasheet.pdf)