MCP4261T-104E from Microchip Tech, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin	Name	Type	Function
1	CS	input	Serial interface chip select input; forcing CS to VIL enables serial commands and forcing it to VIHH enables high-voltage serial commands.
2	SCK	input	SPI serial clock input, a high-voltage tolerant Schmitt-trigger input.
3	SDI	input	SPI serial data input, connected to the host controller's SDO pin.
4	VSS	power_in	Device ground reference.
5	P1B	passive	Potentiometer 1 terminal B; the voltage on this terminal must be between VSS and VDD and it can carry both positive and negative current.
6	P1W	passive	Potentiometer 1 wiper terminal; the voltage on this terminal must be between VSS and VDD and it can carry both positive and negative current.
7	P1A	passive	Potentiometer 1 terminal A (full scale); the voltage on this terminal must be between VSS and VDD and it can carry both positive and negative current.
8	P0A	passive	Potentiometer 0 terminal A (full scale); the voltage on this terminal must be between VSS and VDD and it can carry both positive and negative current.
9	P0W	passive	Potentiometer 0 wiper terminal; the voltage on this terminal must be between VSS and VDD and it can carry both positive and negative current.
10	P0B	passive	Potentiometer 0 terminal B (zero scale); the voltage on this terminal must be between VSS and VDD and it can carry both positive and negative current.
11	WP	input	Hardware EEPROM write protect input used to force the non-volatile memory into write protection.
12	SHDN	input	Hardware shutdown input that forces the resistor network terminals into the hardware shutdown state; it is a high-voltage tolerant Schmitt-trigger input.
13	SDO	output	SPI serial data output, an open-drain output using the internal smart pull-up, which allows the host to read the registers or monitor the command error bit.
14	VDD	power_in	Positive power supply input relative to VSS; below the 2.7V minimum the electrical performance may not meet the data sheet specifications.

Key specifications

Parameter	Value
Manufacturer	Microchip Tech
Package	TSSOP-14
Category	ADC/DAC/Data Conversion
Pins	14

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part	Material	Colour / plating	Datasheet says	Page
contacts		tin	P = Plastic Dual In-line (PDIP) (300 mil), 8/14-lead SN = Plastic Small Outline (SOIC), (150 mil), 8-lead	85

CAD (KiCad official)

Symbol: MCP4261T-104E
Footprint: Package_SO:TSSOP-14_4.4x5mm_P0.65mm
3D model: TSSOP-14 (KiCad packages3D, STEP)
3D model files: mcp4261t-104e-etched.step / mcp4261t-104e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp4261t-104e.step / mcp4261t-104e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

Datasheet: Microchip Tech datasheet (88 pp, sha256 485870dfa4cb7357, retrieved 2026-11-02, tier: manufacturer)
Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF

MCP4261T-104E

Verified MCP4261T-104E

Verification log 1 record

3D Model

Symbol & Footprint

Schematic Symbol

PCB Footprint

Datasheet

README