main
Ray
Publish 0.1.0
bf1ff16
MCP4251-103E
Microchip Tech · Digital Potentiometers · SOIC-14
MCP4251-103E from Microchip Tech, in a SOIC-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS | input | SPI chip select input; forcing CS to VIL enables serial commands and forcing it to VIHH enables high-voltage serial commands (high-voltage tolerant Schmitt-trigger input). |
| 2 | SCK | input | SPI clock input (high-voltage tolerant Schmitt-trigger input, up to 10 MHz). |
| 3 | SDI | input | SPI serial data input, connected to the host controller's SDO pin (high-voltage tolerant Schmitt-trigger input). |
| 4 | VSS | power_in | Device ground reference. |
| 5 | P1B | passive | Potentiometer 1 terminal B, the fixed zero-scale (wiper value 0x00) connection; voltage must be between VSS and VDD. |
| 6 | P1W | passive | Potentiometer 1 wiper terminal; voltage must be between VSS and VDD. |
| 7 | P1A | passive | Potentiometer 1 terminal A, the fixed full-scale connection; voltage must be between VSS and VDD. |
| 8 | P0A | passive | Potentiometer 0 terminal A, the fixed full-scale connection; voltage must be between VSS and VDD. |
| 9 | P0W | passive | Potentiometer 0 wiper terminal; voltage must be between VSS and VDD. |
| 10 | P0B | passive | Potentiometer 0 terminal B, the fixed zero-scale (wiper value 0x00) connection; voltage must be between VSS and VDD. |
| 11 | NC | unconnected | Not internally connected; should be tied to VDD or VSS to reduce possible noise coupling. |
| 12 | SHDN | input | Hardware shutdown input that forces the resistor network terminals into the shutdown state (high-voltage tolerant Schmitt-trigger input). |
| 13 | SDO | output | SPI serial data output, connected to the host controller's SDI pin, used to read registers or monitor the command error bit. |
| 14 | VDD | power_in | Positive power supply input relative to VSS; performance may not meet specifications below 2.7V (device operates from 1.8V to 5.5V). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-14 |
| Category | Data Converters |
| Pins | 14 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VDD | 2.7 | 5.5 | V | 4 | ||
| Supply Voltage (serial interface only) | VDD | 1.8 | 2.7 | V | Serial Interface only | 4 | |
| VDD Start Voltage for Wiper Reset | VBOR | 1.65 | V | RAM retention voltage (VRAM) < VBOR | 4 | ||
| Delay after reset exit | TBORD | 10 | 20 | µs | VDD > VBOR | 4 | |
| Supply Current, serial interface active | IDD | 450 | µA | VDD = 5.5V, CS = VIL, SCK @ 5 MHz, write all 0's to volatile Wiper 0 | 4 | ||
| Supply Current, serial interface inactive | IDD | 2.5 | 5 | µA | CS = VIH, VDD = 5.5V | 4 | |
| Supply Current, serial interface active (VIHH) | IDD | 0.55 | 1 | mA | VDD = 5.5V, CS = VIHH, SCK @ 5 MHz, decrement volatile Wiper 0 | 4 | |
| Resistance (-103 devices) | RAB | 8 | 10 | 12 | kΩ | -103 devices (Note 1), ±20% | 5 |
| Nominal Resistance Match | /RAB0 - RAB1/ / RAB | 0.2 | 1.25 | % | MCP42X1 devices only | 5 | |
| Wiper Resistance | RW | 75 | 160 | Ω | VDD = 5.5 V, IW = 2.0 mA, code = 00h | 5 | |
| Wiper Resistance | RW | 75 | 300 | Ω | VDD = 2.7 V, IW = 2.0 mA, code = 00h | 5 | |
| Maximum current through A, W or B | IW | 2.5 | mA | Note 6, worst case current through wiper when wiper is Full-Scale or Zero Scale | 5 | ||
| Full-Scale Error | VWFSE | -3.5 | -0.1 | LSb | 10 kΩ 8-bit 3.0V ≤ VDD ≤ 5.5V | 6 | |
| Zero-Scale Error | VWZSE | 0.1 | 3.5 | LSb | 10 kΩ 8-bit 3.0V ≤ VDD ≤ 5.5V | 6 | |
| Potentiometer Integral Non-linearity | INL | -1 | 0.5 | 1 | LSb | 8-bit 3.0V ≤ VDD ≤ 5.5V, MCP4XX1 devices only (Note 2) | 6 |
| Potentiometer Differential Non-linearity | DNL | -0.5 | 0.25 | 0.5 | LSb | 8-bit 3.0V ≤ VDD ≤ 5.5V, MCP4XX1 devices only (Note 2) | 6 |
| Rheostat Integral Non-linearity | R-INL | -1.5 | 0.5 | 1.5 | LSb | 10 kΩ 8-bit 5.5V, IW = 450 µA | 7 |
| Rheostat Integral Non-linearity | R-INL | -5.5 | 2.5 | 5.5 | LSb | 10 kΩ 8-bit 3.0V, IW = 240 µA (Note 7) | 7 |
| Rheostat Differential Non-linearity | R-DNL | -0.5 | 0.25 | 0.5 | LSb | 10 kΩ 8-bit 5.5V, IW = 450 µA | 8 |
| Rheostat Differential Non-linearity | R-DNL | -1 | 0.25 | 1 | LSb | 10 kΩ 8-bit 3.0V (Note 7) | 8 |
| Schmitt Trigger High Input Threshold | VIH | 0.45 | VDD | 2.7V ≤ VDD ≤ 5.5V | 9 | ||
| Schmitt Trigger Low Input Threshold | VIL | 0.2 | VDD | 9 | |||
| High Voltage Limit | VMAX | 12.5 | V | Pin can tolerate VMAX or less (Note 6) | 9 | ||
| Output Low Voltage (SDO) | VOL | 0.3 | VDD | IOL = 5 mA, VDD = 5.5V | 9 | ||
| Output High Voltage (SDO) | VOH | 0.7 | VDD | IOH = -2.5 mA, VDD = 5.5V | 9 | ||
| Weak Pull-up / Pull-down Current | IPU | 1.75 | mA | Internal VDD pull-up, VIHH pull-down, VDD = 5.5V, VCS = 12.5V | 9 | ||
| Input Leakage Current | IIL | -1 | 1 | µA | VIN = VDD and VIN = VSS | 9 | |
| SCK Input Frequency | FSCK | 10 | MHz | VDD = 2.7V to 5.5V | 11 | ||
| SCK input high time | TscH | 45 | ns | VDD = 2.7V to 5.5V | 11 | ||
| SCK input low time | TscL | 45 | ns | VDD = 2.7V to 5.5V | 11 | ||
| SDO data output valid after SCK↓ edge | TscL2DOV | 70 | ns | VDD = 2.7V to 5.5V | 11 | ||
| Nominal Resistance Tempco | ΔRAB/ΔT | 50 | ppm/°C | TA = -20°C to +70°C | 5 | ||
| Nominal Resistance Tempco | ΔRAB/ΔT | 100 | ppm/°C | TA = -40°C to +85°C | 5 | ||
| Nominal Resistance Tempco | ΔRAB/ΔT | 150 | ppm/°C | TA = -40°C to +125°C | 5 | ||
| Ratiometric Tempco | ΔVWB/ΔT | 15 | ppm/°C | Code = Midscale (80h or 40h) | 5 | ||
| Leakage current into A, W or B | IWL | 100 | nA | MCP4XX1 PxA = PxW = PxB = VSS | 5 | ||
| Bandwidth -3 dB | BW | 1 | MHz | 10 kΩ 8-bit Code = 80h, load = 30 pF | 6 | ||
| Capacitance (PA) | CAW | 75 | pF | f =1 MHz, Code = Full-Scale | 8 | ||
| Capacitance (PW) | CW | 120 | pF | f =1 MHz, Code = Full-Scale | 8 | ||
| Capacitance (PB) | CBW | 75 | pF | f =1 MHz, Code = Full-Scale | 8 | ||
| CS Pull-up/Pull-down Resistance | RCS | 16 | kΩ | VDD = 5.5V, VCS = 3V | 9 | ||
| Pin Capacitance | CIN, COUT | 10 | pF | fC = 20 MHz | 9 | ||
| Voltage on VDD with respect to VSS | VDD | -0.6 | 7 | V | 3 | ||
| Voltage on CS, SCK, SDI, SDI/SDO, SHDN with respect to VSS | -0.6 | 12.5 | V | 3 | |||
| Voltage on PxA, PxW, PxB, SDO with respect to VSS | -0.3 | V | Upper limit printed as VDD + 0.3V | 3 | |||
| Input clamp current | IIK | -20 | 20 | mA | VI < 0, VI > VDD, VI > VPP on HV pins | 3 | |
| Output clamp current | IOK | -20 | 20 | mA | VO < 0 or VO > VDD | 3 | |
| Maximum current into PXA, PXW & PXB pins | -2.5 | 2.5 | mA | 3 | |||
| Maximum current into VDD pin | 100 | mA | 3 | ||||
| Maximum current out of VSS pin | 100 | mA | 3 | ||||
| Storage temperature | -65 | 150 | °C | 3 | |||
| Ambient temperature with power applied | -40 | 125 | °C | 3 | |||
| Maximum Junction Temperature | TJ | 150 | °C | 3 | |||
| Operating Temperature Range | TA | -40 | 125 | °C | 14 | ||
| Thermal Resistance, 14L-SOIC | θJA | 95.3 | °C/W | 14 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | P = Plastic Dual In-line (PDIP) (300 mil), 8/14-lead SN = Plastic Small Outline (SOIC), (150 mil), 8-lead | 85 |
CAD (KiCad official)
- Symbol:
MCP4251-103E - Footprint:
Package_SO:SOIC-14_3.9x8.7mm_P1.27mm - 3D model: SOIC-14 (KiCad packages3D, STEP)
- 3D model files:
mcp4251-103e-etched.step/mcp4251-103e-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp4251-103e.step/mcp4251-103e.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (88 pp, sha256
6c60b083b2ef0a92, retrieved 2026-10-23, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MCP4251-103E
**Microchip Tech** · Digital Potentiometers · SOIC-14
MCP4251-103E from Microchip Tech, in a SOIC-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS | input | SPI chip select input; forcing CS to VIL enables serial commands and forcing it to VIHH enables high-voltage serial commands (high-voltage tolerant Schmitt-trigger input). |
| 2 | SCK | input | SPI clock input (high-voltage tolerant Schmitt-trigger input, up to 10 MHz). |
| 3 | SDI | input | SPI serial data input, connected to the host controller's SDO pin (high-voltage tolerant Schmitt-trigger input). |
| 4 | VSS | power_in | Device ground reference. |
| 5 | P1B | passive | Potentiometer 1 terminal B, the fixed zero-scale (wiper value 0x00) connection; voltage must be between VSS and VDD. |
| 6 | P1W | passive | Potentiometer 1 wiper terminal; voltage must be between VSS and VDD. |
| 7 | P1A | passive | Potentiometer 1 terminal A, the fixed full-scale connection; voltage must be between VSS and VDD. |
| 8 | P0A | passive | Potentiometer 0 terminal A, the fixed full-scale connection; voltage must be between VSS and VDD. |
| 9 | P0W | passive | Potentiometer 0 wiper terminal; voltage must be between VSS and VDD. |
| 10 | P0B | passive | Potentiometer 0 terminal B, the fixed zero-scale (wiper value 0x00) connection; voltage must be between VSS and VDD. |
| 11 | NC | unconnected | Not internally connected; should be tied to VDD or VSS to reduce possible noise coupling. |
| 12 | SHDN | input | Hardware shutdown input that forces the resistor network terminals into the shutdown state (high-voltage tolerant Schmitt-trigger input). |
| 13 | SDO | output | SPI serial data output, connected to the host controller's SDI pin, used to read registers or monitor the command error bit. |
| 14 | VDD | power_in | Positive power supply input relative to VSS; performance may not meet specifications below 2.7V (device operates from 1.8V to 5.5V). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-14 |
| Category | Data Converters |
| Pins | 14 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VDD | 2.7 | | 5.5 | V | | 4 |
| Supply Voltage (serial interface only) | VDD | 1.8 | | 2.7 | V | Serial Interface only | 4 |
| VDD Start Voltage for Wiper Reset | VBOR | | | 1.65 | V | RAM retention voltage (VRAM) < VBOR | 4 |
| Delay after reset exit | TBORD | | 10 | 20 | µs | VDD > VBOR | 4 |
| Supply Current, serial interface active | IDD | | | 450 | µA | VDD = 5.5V, CS = VIL, SCK @ 5 MHz, write all 0's to volatile Wiper 0 | 4 |
| Supply Current, serial interface inactive | IDD | | 2.5 | 5 | µA | CS = VIH, VDD = 5.5V | 4 |
| Supply Current, serial interface active (VIHH) | IDD | | 0.55 | 1 | mA | VDD = 5.5V, CS = VIHH, SCK @ 5 MHz, decrement volatile Wiper 0 | 4 |
| Resistance (-103 devices) | RAB | 8 | 10 | 12 | kΩ | -103 devices (Note 1), ±20% | 5 |
| Nominal Resistance Match | /RAB0 - RAB1/ / RAB | | 0.2 | 1.25 | % | MCP42X1 devices only | 5 |
| Wiper Resistance | RW | | 75 | 160 | Ω | VDD = 5.5 V, IW = 2.0 mA, code = 00h | 5 |
| Wiper Resistance | RW | | 75 | 300 | Ω | VDD = 2.7 V, IW = 2.0 mA, code = 00h | 5 |
| Maximum current through A, W or B | IW | | | 2.5 | mA | Note 6, worst case current through wiper when wiper is Full-Scale or Zero Scale | 5 |
| Full-Scale Error | VWFSE | -3.5 | -0.1 | | LSb | 10 kΩ 8-bit 3.0V ≤ VDD ≤ 5.5V | 6 |
| Zero-Scale Error | VWZSE | | 0.1 | 3.5 | LSb | 10 kΩ 8-bit 3.0V ≤ VDD ≤ 5.5V | 6 |
| Potentiometer Integral Non-linearity | INL | -1 | 0.5 | 1 | LSb | 8-bit 3.0V ≤ VDD ≤ 5.5V, MCP4XX1 devices only (Note 2) | 6 |
| Potentiometer Differential Non-linearity | DNL | -0.5 | 0.25 | 0.5 | LSb | 8-bit 3.0V ≤ VDD ≤ 5.5V, MCP4XX1 devices only (Note 2) | 6 |
| Rheostat Integral Non-linearity | R-INL | -1.5 | 0.5 | 1.5 | LSb | 10 kΩ 8-bit 5.5V, IW = 450 µA | 7 |
| Rheostat Integral Non-linearity | R-INL | -5.5 | 2.5 | 5.5 | LSb | 10 kΩ 8-bit 3.0V, IW = 240 µA (Note 7) | 7 |
| Rheostat Differential Non-linearity | R-DNL | -0.5 | 0.25 | 0.5 | LSb | 10 kΩ 8-bit 5.5V, IW = 450 µA | 8 |
| Rheostat Differential Non-linearity | R-DNL | -1 | 0.25 | 1 | LSb | 10 kΩ 8-bit 3.0V (Note 7) | 8 |
| Schmitt Trigger High Input Threshold | VIH | 0.45 | | | VDD | 2.7V ≤ VDD ≤ 5.5V | 9 |
| Schmitt Trigger Low Input Threshold | VIL | | | 0.2 | VDD | | 9 |
| High Voltage Limit | VMAX | | | 12.5 | V | Pin can tolerate VMAX or less (Note 6) | 9 |
| Output Low Voltage (SDO) | VOL | | | 0.3 | VDD | IOL = 5 mA, VDD = 5.5V | 9 |
| Output High Voltage (SDO) | VOH | 0.7 | | | VDD | IOH = -2.5 mA, VDD = 5.5V | 9 |
| Weak Pull-up / Pull-down Current | IPU | | | 1.75 | mA | Internal VDD pull-up, VIHH pull-down, VDD = 5.5V, VCS = 12.5V | 9 |
| Input Leakage Current | IIL | -1 | | 1 | µA | VIN = VDD and VIN = VSS | 9 |
| SCK Input Frequency | FSCK | | | 10 | MHz | VDD = 2.7V to 5.5V | 11 |
| SCK input high time | TscH | 45 | | | ns | VDD = 2.7V to 5.5V | 11 |
| SCK input low time | TscL | 45 | | | ns | VDD = 2.7V to 5.5V | 11 |
| SDO data output valid after SCK↓ edge | TscL2DOV | | | 70 | ns | VDD = 2.7V to 5.5V | 11 |
| Nominal Resistance Tempco | ΔRAB/ΔT | | 50 | | ppm/°C | TA = -20°C to +70°C | 5 |
| Nominal Resistance Tempco | ΔRAB/ΔT | | 100 | | ppm/°C | TA = -40°C to +85°C | 5 |
| Nominal Resistance Tempco | ΔRAB/ΔT | | 150 | | ppm/°C | TA = -40°C to +125°C | 5 |
| Ratiometric Tempco | ΔVWB/ΔT | | 15 | | ppm/°C | Code = Midscale (80h or 40h) | 5 |
| Leakage current into A, W or B | IWL | | 100 | | nA | MCP4XX1 PxA = PxW = PxB = VSS | 5 |
| Bandwidth -3 dB | BW | | 1 | | MHz | 10 kΩ 8-bit Code = 80h, load = 30 pF | 6 |
| Capacitance (PA) | CAW | | 75 | | pF | f =1 MHz, Code = Full-Scale | 8 |
| Capacitance (PW) | CW | | 120 | | pF | f =1 MHz, Code = Full-Scale | 8 |
| Capacitance (PB) | CBW | | 75 | | pF | f =1 MHz, Code = Full-Scale | 8 |
| CS Pull-up/Pull-down Resistance | RCS | | 16 | | kΩ | VDD = 5.5V, VCS = 3V | 9 |
| Pin Capacitance | CIN, COUT | | 10 | | pF | fC = 20 MHz | 9 |
| Voltage on VDD with respect to VSS | VDD | -0.6 | | 7 | V | | 3 |
| Voltage on CS, SCK, SDI, SDI/SDO, SHDN with respect to VSS | | -0.6 | | 12.5 | V | | 3 |
| Voltage on PxA, PxW, PxB, SDO with respect to VSS | | -0.3 | | | V | Upper limit printed as VDD + 0.3V | 3 |
| Input clamp current | IIK | -20 | | 20 | mA | VI < 0, VI > VDD, VI > VPP on HV pins | 3 |
| Output clamp current | IOK | -20 | | 20 | mA | VO < 0 or VO > VDD | 3 |
| Maximum current into PXA, PXW & PXB pins | | -2.5 | | 2.5 | mA | | 3 |
| Maximum current into VDD pin | | | | 100 | mA | | 3 |
| Maximum current out of VSS pin | | | | 100 | mA | | 3 |
| Storage temperature | | -65 | | 150 | °C | | 3 |
| Ambient temperature with power applied | | -40 | | 125 | °C | | 3 |
| Maximum Junction Temperature | TJ | | | 150 | °C | | 3 |
| Operating Temperature Range | TA | -40 | | 125 | °C | | 14 |
| Thermal Resistance, 14L-SOIC | θJA | | 95.3 | | °C/W | | 14 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | | tin | P = Plastic Dual In-line (PDIP) (300 mil), 8/14-lead SN = Plastic Small Outline (SOIC), (150 mil), 8-lead | 85 |
## CAD (KiCad official)
- Symbol: `MCP4251-103E`
- Footprint: `Package_SO:SOIC-14_3.9x8.7mm_P1.27mm`
- 3D model: SOIC-14 (KiCad packages3D, STEP)
- 3D model files: `mcp4251-103e-etched.step` / `mcp4251-103e-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mcp4251-103e.step` / `mcp4251-103e.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/mcp4251-103e-datasheet.pdf) (88 pp, sha256 `6c60b083b2ef0a92`, retrieved 2026-10-23, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mcp4251-103e-datasheet.pdf)