main
Ray
Publish 0.1.0
a0ff4b6
MCP39F511-E
Microchip Tech · Pre-ordered MCUs · QFN-28-EP(5x5)
MCP39F511-E from Microchip Tech, in a QFN-28-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EVENT1 | output | Event 1 output pin, configured as an output flag through the Event Configuration register. |
| 2 | NC | unconnected | No connect; must be left floating. |
| 3 | NC | unconnected | No connect; must be left floating. |
| 4 | UART_RX | input | UART communication receive pin of the asynchronous full-duplex UART (eight bits with Start and Stop bit). |
| 5 | COMMONA | passive | Internal connection pin that must be connected to pin 13 (COMMONB). |
| 6 | OSCI | input | Oscillator crystal connection or external clock input; optional 4 MHz crystal, otherwise the device clocks from the internal 4 MHz oscillator. |
| 7 | OSCO | passive | Oscillator crystal connection pin for the optional 4 MHz crystal, with appropriate load capacitance. |
| 8 | NC | unconnected | No connect; must be left floating. |
| 9 | NC | unconnected | No connect; must be left floating. |
| 10 | RESET | input | Active-low Schmitt-triggered reset for the Delta-Sigma ADCs, PGA, internal VREF and analog front-end blocks. |
| 11 | AVDD | power_in | Analog power supply pin, maintained between +2.7V and +3.6V with 0.1 µF ceramic bypass capacitors recommended. |
| 12 | UART_TX | output | UART communication transmit pin of the asynchronous full-duplex UART. |
| 13 | COMMONB | passive | Internal connection pin that must be connected to pin 5 (COMMONA). |
| 14 | PWM | output | Dedicated PWM output with frequency and duty cycle set by the PWM Frequency and PWM Duty Cycle registers. |
| 15 | EVENT2 | output | Event 2 output pin, configured as an output flag through the Event Configuration register. |
| 16 | I1+ | input | Noninverting current channel input of the 24-bit Delta-Sigma ADC, range ±600 mV peak/GAIN with VREF = 1.2V, absolute maximum ±1V without distortion and ±6V without breaking. |
| 17 | I1- | input | Inverting current channel input of the 24-bit Delta-Sigma ADC, range ±600 mV peak/GAIN with VREF = 1.2V, absolute maximum ±1V without distortion and ±6V without breaking. |
| 18 | V1- | input | Inverting voltage channel input of the 24-bit Delta-Sigma ADC, range ±600 mV peak/GAIN with VREF = 1.2V, absolute maximum ±1V without distortion and ±2V without breaking. |
| 19 | V1+ | input | Noninverting voltage channel input of the 24-bit Delta-Sigma ADC, range ±600 mV peak/GAIN with VREF = 1.2V, absolute maximum ±1V without distortion and ±2V without breaking. |
| 20 | AN_IN | input | Analog input to the SAR ADC for temperature measurement (MCP9700A recommended) or general purpose use. |
| 21 | AGND | power_in | Analog ground, return path for internal analog circuitry (ADCs, PGA, voltage reference, POR). |
| 22 | ZCD | output | Zero crossing detection logic output that transitions at each zero crossing of the voltage channel input. |
| 23 | REFIN+/OUT | bidirectional | Noninverting voltage reference input and internal reference output pin. |
| 24 | DGND | power_in | Digital ground, return path for internal digital circuitry. |
| 25 | DVDD | power_in | Digital power supply pin. |
| 26 | MCLR | input | Master clear for the device. |
| 27 | DGND | power_in | Digital ground, return path for internal digital circuitry. |
| 28 | DR | unconnected | Data Ready pin; must be left floating. |
| 29 | EP | power_in | Exposed thermal pad, to be connected to pins 24 and 27 (DGND). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-28-EP(5x5) |
| Category | Embedded Processors & Controllers |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| DVDD supply voltage | DVDD | -0.3 | 4.5 | V | 4 | ||
| AVDD supply voltage | AVDD | -0.3 | 4 | V | 4 | ||
| Digital inputs and outputs | -0.3 | 4 | V | w.r.t. AGND | 4 | ||
| Analog inputs (I+,I-,V+,V-) | -2 | 2 | V | w.r.t. AGND | 4 | ||
| Maximum current out of DGND pin | 300 | mA | 4 | ||||
| Storage temperature | -65 | 150 | °C | 4 | |||
| Ambient temperature with power applied | -40 | 125 | °C | 4 | |||
| Soldering temperature of leads | 300 | °C | 10 seconds | 4 | |||
| Operating voltage | AVDD, DVDD | 2.7 | 3.6 | V | 7 | ||
| Operating temperature range | TA | -40 | 125 | °C | 8 | ||
| Analog input absolute voltage | VIN | -1 | 1 | V | 5 | ||
| Differential input voltage range | (I1+, I1-),(V1+, V1-) | -600 | 600 | mV | VREF = 1.2V, ±600/GAIN, proportional to VREF | 5 | |
| Offset error | VOS | -1 | 1 | mV | 5 | ||
| Gain error | GE | -4 | 4 | % | Note 5 | 5 | |
| Differential input impedance G=1 | ZIN | 232 | kΩ | G=1 | 5 | ||
| Differential input impedance G=2 | ZIN | 142 | kΩ | G=2 | 5 | ||
| Differential input impedance G=4 | ZIN | 72 | kΩ | G=4 | 5 | ||
| Differential input impedance G=8 | ZIN | 38 | kΩ | G=8 | 5 | ||
| Differential input impedance G=16 | ZIN | 36 | kΩ | G = 16 | 5 | ||
| Differential input impedance G=32 | ZIN | 33 | kΩ | G = 32 | 5 | ||
| Signal-to-noise and distortion ratio | SINAD | 92 | 94.5 | dB | Note 6 | 5 | |
| Total harmonic distortion | THD | -106.5 | -103 | dBc | Note 6 | 5 | |
| Signal-to-noise ratio | SNR | 92 | 95 | dB | Note 6 | 5 | |
| Recommended impedance of analog voltage source | RIN | 2.5 | kΩ | 6 | |||
| Integral nonlinearity | INL | 1 | 2 | LSb | ± | 6 | |
| Differential nonlinearity | DNL | 1 | 1.5 | LSb | ± | 6 | |
| SAR gain error | GERR | 1 | 3 | LSb | ± | 6 | |
| SAR offset error | EOFF | 1 | 2 | LSb | ± | 6 | |
| UART baud rate | UDB | 1.2 | 115.2 | kbps | Lower baud rates selectable only on system versions 0xFA14 and later | 6 | |
| Master clock and crystal frequency | fMCLK | -2 | 4 | 2 | MHz | tolerance in % | 6 |
| Capacitive loading on OSCO pin | COSC2 | 15 | pF | When an external clock is used to drive the device | 6 | ||
| Internal voltage reference tolerance | VREF | -2 | 1.2 | 2 | V | tolerance in % | 6 |
| Input capacitance (voltage reference input) | 10 | pF | 6 | ||||
| Absolute voltage on VREF+ pin | VREF+ | 1.1 | 1.3 | V | AGND + 1.1V to AGND + 1.3V | 6 | |
| DVDD start voltage for POR | VPOR | 0.7 | V | 7 | |||
| DVDD rise rate for POR | SDVDD | 0.05 | V/ms | 0, 3.3V in 0.1s, 0, 2.5V in 60 ms | 7 | ||
| AVDD start voltage for POR | VPOR | 2.1 | V | 7 | |||
| AVDD rise rate for POR | SAVDD | 0.042 | V/ms | 0, 2.4V in 50 ms | 7 | ||
| EEPROM cell endurance | EPS | 100000 | E/W | 7 | |||
| EEPROM characteristic retention | TRETDD | 40 | years | Provided no other specifications are violated | 7 | ||
| High-level input voltage | VIH | 0.8 | 1 | V | 0.8 DVDD to DVDD (values are multipliers of DVDD) | 8 | |
| Low-level input voltage | VIL | 0 | 0.2 | V | 0 to 0.2 DVDD (values are multipliers of DVDD) | 8 | |
| High-level output voltage | VOH | 3 | V | IOH = -3.0 mA, VDD = 3.6V | 8 | ||
| Low-level output voltage | VOL | 0.4 | V | IOL = 4.0 mA, VDD = 3.6V | 8 | ||
| Input leakage current | ILI | 1 | µA | 8 | |||
| Input leakage current, digital output pins | ILI | 0.05 | 0.1 | µA | Digital Output pins only (ZCD, PWM, EVENT1, EVENT2) | 8 | |
| Active power accuracy | P | 0.1 | % | 4000:1 Dynamic Range on Current Channel | 4 | ||
| Offset error drift | 0.5 | µV/°C | 5 | ||||
| Gain error drift | 1 | ppm/°C | 5 | ||||
| Voltage reference temperature coefficient | TCVREF | 10 | ppm/°C | TA = -40°C to +85°C, VREFEXT = 0 | 6 | ||
| Operating current | IDD | 13 | mA | 7 | |||
| Thermal resistance, 28LD 5x5 QFN | θJA | 36.9 | °C/W | 8 |
CAD (KiCad official)
- Symbol:
MCP39F511-E - Footprint:
Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm - 3D model: QFN-28-EP(5x5) (KiCad packages3D, STEP)
- 3D model files:
mcp39f511-e-etched.step/mcp39f511-e-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp39f511-e.step/mcp39f511-e.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (62 pp, sha256
af6a9dc85fb7c1ae, retrieved 2026-10-27, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MCP39F511-E
**Microchip Tech** · Pre-ordered MCUs · QFN-28-EP(5x5)
MCP39F511-E from Microchip Tech, in a QFN-28-EP(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EVENT1 | output | Event 1 output pin, configured as an output flag through the Event Configuration register. |
| 2 | NC | unconnected | No connect; must be left floating. |
| 3 | NC | unconnected | No connect; must be left floating. |
| 4 | UART_RX | input | UART communication receive pin of the asynchronous full-duplex UART (eight bits with Start and Stop bit). |
| 5 | COMMONA | passive | Internal connection pin that must be connected to pin 13 (COMMONB). |
| 6 | OSCI | input | Oscillator crystal connection or external clock input; optional 4 MHz crystal, otherwise the device clocks from the internal 4 MHz oscillator. |
| 7 | OSCO | passive | Oscillator crystal connection pin for the optional 4 MHz crystal, with appropriate load capacitance. |
| 8 | NC | unconnected | No connect; must be left floating. |
| 9 | NC | unconnected | No connect; must be left floating. |
| 10 | RESET | input | Active-low Schmitt-triggered reset for the Delta-Sigma ADCs, PGA, internal VREF and analog front-end blocks. |
| 11 | AVDD | power_in | Analog power supply pin, maintained between +2.7V and +3.6V with 0.1 µF ceramic bypass capacitors recommended. |
| 12 | UART_TX | output | UART communication transmit pin of the asynchronous full-duplex UART. |
| 13 | COMMONB | passive | Internal connection pin that must be connected to pin 5 (COMMONA). |
| 14 | PWM | output | Dedicated PWM output with frequency and duty cycle set by the PWM Frequency and PWM Duty Cycle registers. |
| 15 | EVENT2 | output | Event 2 output pin, configured as an output flag through the Event Configuration register. |
| 16 | I1+ | input | Noninverting current channel input of the 24-bit Delta-Sigma ADC, range ±600 mV peak/GAIN with VREF = 1.2V, absolute maximum ±1V without distortion and ±6V without breaking. |
| 17 | I1- | input | Inverting current channel input of the 24-bit Delta-Sigma ADC, range ±600 mV peak/GAIN with VREF = 1.2V, absolute maximum ±1V without distortion and ±6V without breaking. |
| 18 | V1- | input | Inverting voltage channel input of the 24-bit Delta-Sigma ADC, range ±600 mV peak/GAIN with VREF = 1.2V, absolute maximum ±1V without distortion and ±2V without breaking. |
| 19 | V1+ | input | Noninverting voltage channel input of the 24-bit Delta-Sigma ADC, range ±600 mV peak/GAIN with VREF = 1.2V, absolute maximum ±1V without distortion and ±2V without breaking. |
| 20 | AN_IN | input | Analog input to the SAR ADC for temperature measurement (MCP9700A recommended) or general purpose use. |
| 21 | AGND | power_in | Analog ground, return path for internal analog circuitry (ADCs, PGA, voltage reference, POR). |
| 22 | ZCD | output | Zero crossing detection logic output that transitions at each zero crossing of the voltage channel input. |
| 23 | REFIN+/OUT | bidirectional | Noninverting voltage reference input and internal reference output pin. |
| 24 | DGND | power_in | Digital ground, return path for internal digital circuitry. |
| 25 | DVDD | power_in | Digital power supply pin. |
| 26 | MCLR | input | Master clear for the device. |
| 27 | DGND | power_in | Digital ground, return path for internal digital circuitry. |
| 28 | DR | unconnected | Data Ready pin; must be left floating. |
| 29 | EP | power_in | Exposed thermal pad, to be connected to pins 24 and 27 (DGND). |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | QFN-28-EP(5x5) |
| Category | Embedded Processors & Controllers |
| Pins | 29 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| DVDD supply voltage | DVDD | -0.3 | | 4.5 | V | | 4 |
| AVDD supply voltage | AVDD | -0.3 | | 4 | V | | 4 |
| Digital inputs and outputs | | -0.3 | | 4 | V | w.r.t. AGND | 4 |
| Analog inputs (I+,I-,V+,V-) | | -2 | | 2 | V | w.r.t. AGND | 4 |
| Maximum current out of DGND pin | | | | 300 | mA | | 4 |
| Storage temperature | | -65 | | 150 | °C | | 4 |
| Ambient temperature with power applied | | -40 | | 125 | °C | | 4 |
| Soldering temperature of leads | | | | 300 | °C | 10 seconds | 4 |
| Operating voltage | AVDD, DVDD | 2.7 | | 3.6 | V | | 7 |
| Operating temperature range | TA | -40 | | 125 | °C | | 8 |
| Analog input absolute voltage | VIN | -1 | | 1 | V | | 5 |
| Differential input voltage range | (I1+, I1-),(V1+, V1-) | -600 | | 600 | mV | VREF = 1.2V, ±600/GAIN, proportional to VREF | 5 |
| Offset error | VOS | -1 | | 1 | mV | | 5 |
| Gain error | GE | -4 | | 4 | % | Note 5 | 5 |
| Differential input impedance G=1 | ZIN | 232 | | | kΩ | G=1 | 5 |
| Differential input impedance G=2 | ZIN | 142 | | | kΩ | G=2 | 5 |
| Differential input impedance G=4 | ZIN | 72 | | | kΩ | G=4 | 5 |
| Differential input impedance G=8 | ZIN | 38 | | | kΩ | G=8 | 5 |
| Differential input impedance G=16 | ZIN | 36 | | | kΩ | G = 16 | 5 |
| Differential input impedance G=32 | ZIN | 33 | | | kΩ | G = 32 | 5 |
| Signal-to-noise and distortion ratio | SINAD | 92 | 94.5 | | dB | Note 6 | 5 |
| Total harmonic distortion | THD | | -106.5 | -103 | dBc | Note 6 | 5 |
| Signal-to-noise ratio | SNR | 92 | 95 | | dB | Note 6 | 5 |
| Recommended impedance of analog voltage source | RIN | | | 2.5 | kΩ | | 6 |
| Integral nonlinearity | INL | | 1 | 2 | LSb | ± | 6 |
| Differential nonlinearity | DNL | | 1 | 1.5 | LSb | ± | 6 |
| SAR gain error | GERR | | 1 | 3 | LSb | ± | 6 |
| SAR offset error | EOFF | | 1 | 2 | LSb | ± | 6 |
| UART baud rate | UDB | 1.2 | | 115.2 | kbps | Lower baud rates selectable only on system versions 0xFA14 and later | 6 |
| Master clock and crystal frequency | fMCLK | -2 | 4 | 2 | MHz | tolerance in % | 6 |
| Capacitive loading on OSCO pin | COSC2 | | | 15 | pF | When an external clock is used to drive the device | 6 |
| Internal voltage reference tolerance | VREF | -2 | 1.2 | 2 | V | tolerance in % | 6 |
| Input capacitance (voltage reference input) | | | | 10 | pF | | 6 |
| Absolute voltage on VREF+ pin | VREF+ | 1.1 | | 1.3 | V | AGND + 1.1V to AGND + 1.3V | 6 |
| DVDD start voltage for POR | VPOR | | | 0.7 | V | | 7 |
| DVDD rise rate for POR | SDVDD | 0.05 | | | V/ms | 0, 3.3V in 0.1s, 0, 2.5V in 60 ms | 7 |
| AVDD start voltage for POR | VPOR | | | 2.1 | V | | 7 |
| AVDD rise rate for POR | SAVDD | 0.042 | | | V/ms | 0, 2.4V in 50 ms | 7 |
| EEPROM cell endurance | EPS | 100000 | | | E/W | | 7 |
| EEPROM characteristic retention | TRETDD | 40 | | | years | Provided no other specifications are violated | 7 |
| High-level input voltage | VIH | 0.8 | | 1 | V | 0.8 DVDD to DVDD (values are multipliers of DVDD) | 8 |
| Low-level input voltage | VIL | 0 | | 0.2 | V | 0 to 0.2 DVDD (values are multipliers of DVDD) | 8 |
| High-level output voltage | VOH | 3 | | | V | IOH = -3.0 mA, VDD = 3.6V | 8 |
| Low-level output voltage | VOL | | | 0.4 | V | IOL = 4.0 mA, VDD = 3.6V | 8 |
| Input leakage current | ILI | | | 1 | µA | | 8 |
| Input leakage current, digital output pins | ILI | | 0.05 | 0.1 | µA | Digital Output pins only (ZCD, PWM, EVENT1, EVENT2) | 8 |
| Active power accuracy | P | | 0.1 | | % | 4000:1 Dynamic Range on Current Channel | 4 |
| Offset error drift | | | 0.5 | | µV/°C | | 5 |
| Gain error drift | | | 1 | | ppm/°C | | 5 |
| Voltage reference temperature coefficient | TCVREF | | 10 | | ppm/°C | TA = -40°C to +85°C, VREFEXT = 0 | 6 |
| Operating current | IDD | | 13 | | mA | | 7 |
| Thermal resistance, 28LD 5x5 QFN | θJA | | 36.9 | | °C/W | | 8 |
## CAD (KiCad official)
- Symbol: `MCP39F511-E`
- Footprint: `Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm`
- 3D model: QFN-28-EP(5x5) (KiCad packages3D, STEP)
- 3D model files: `mcp39f511-e-etched.step` / `mcp39f511-e-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mcp39f511-e.step` / `mcp39f511-e.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](https://ww1.microchip.com/downloads/en/DeviceDoc/20005393B.pdf) (62 pp, sha256 `af6a9dc85fb7c1ae`, retrieved 2026-10-27, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mcp39f511-e-datasheet.pdf)