3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMCP3905A-I
Microchip Tech · Battery Management ICs · SSOP-24-208mil
MCP3905A-I from Microchip Tech, in a SSOP-24-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DVDD | power_in | Digital power supply pin for the digital circuitry; maintain 5V ±10% for specified operation with bypass capacitors per Section 5.0. |
| 2 | HPF | input | High-pass filter control for both input channels; logic 1 enables the filters to remove DC offset and logic 0 disables them to allow DC voltages to be measured. |
| 3 | AVDD | power_in | Analog power supply pin for the analog circuitry; maintain 5V ±10% for specified operation with bypass capacitors per Section 5.0. |
| 4 | NC | unconnected | No connect. |
| 5 | CH0+ | passive | Non-inverting fully differential analog input for Channel 0 (current, PGA); maximum differential voltage ±470 mV/GAIN and maximum absolute voltage ±1 V to AGND, with up to ±6 V withstood without permanent damage. |
| 6 | CH0- | passive | Inverting fully differential analog input for Channel 0 (current, PGA); maximum differential voltage ±470 mV/GAIN and maximum absolute voltage ±1 V to AGND, with up to ±6 V withstood without permanent damage. |
| 7 | CH1- | passive | Inverting fully differential analog input for Channel 1 (voltage); maximum differential voltage ±660 mV and maximum absolute voltage ±1 V to AGND, with up to ±6 V withstood without permanent damage. |
| 8 | CH1+ | passive | Non-inverting fully differential analog input for Channel 1 (voltage); maximum differential voltage ±660 mV and maximum absolute voltage ±1 V to AGND, with up to ±6 V withstood without permanent damage. |
| 9 | MCLR | input | Master clear; a logic 0 resets both delta-sigma ADCs and all digital registers, holding the ADC outputs at 0x0000h. |
| 10 | REFIN/OUT | bidirectional | Output of the internal 2.4V reference (±2%, 15 ppm/°C typical); an external reference from 2.2 V to 2.6 V may be applied, and bypass capacitors to AGND are required even with the internal reference. |
| 11 | AGND | power_in | Analog ground return for the ADCs, PGA, band gap reference and POR; must be connected to the same ground as DGND. |
| 12 | F2 | input | Frequency control logic input that selects the HFOUT frequency constant (HFC) together with F1 and F0. |
| 13 | F1 | input | Frequency control logic input that selects the FOUT0/1 frequency constant (FC) and HFOUT constant together with F0 and F2. |
| 14 | F0 | input | Frequency control logic input that selects the FOUT0/1 frequency constant (FC) together with F1. |
| 15 | G1 | input | Gain control logic input that selects the Channel 0 PGA gain together with G0 (1, 8 or 16; 1, 8 or 16 for MCP3905A/L, 32 instead of 2 for MCP3906A). |
| 16 | G0 | input | Gain control logic input that selects the Channel 0 PGA gain together with G1. |
| 17 | OSC1 | input | Oscillator crystal connection or clock input; master clock range 1 MHz to 4 MHz with typical 3.579545 MHz. |
| 18 | OSC2 | output | Oscillator crystal connection or clock output; appropriate load capacitance must be connected for proper operation. |
| 19 | NC | unconnected | No connect. |
| 20 | NEG | output | Negative power logic output that goes to logic 1 when the phase difference exceeds 90° (measured real power negative), synchronous with the rising edge of HFOUT. |
| 21 | DGND | power_in | Digital ground return for the SINC filters, multiplier, HPF, LPF, DTF converter and oscillator; must be connected to the same ground as AGND. |
| 22 | HFOUT | output | High-frequency logic output carrying instantaneous real-power pulses, intended for meter calibration; period set by the HFC constant selected by F0, F1 and F2. |
| 23 | FOUT1 | output | Differential mechanical counter logic output carrying average real-power pulses, with high output drive for electromechanical counters and 2-phase stepper motors; frequency set by F0 and F1. |
| 24 | FOUT0 | output | Differential mechanical counter logic output carrying average real-power pulses, with high output drive for electromechanical counters and 2-phase stepper motors; frequency set by F0 and F1. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SSOP-24-208mil |
| Category | Power Supply Chip |
| Pins | 24 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| System Gain Error | 3 | 10 | % | Note 2, Note 5 | 3 | ||
| Offset Error | VOS | 2 | 5 | mV | Referred to Input | 3 | |
| Internal voltage reference tolerance | -2 | 2 | % | 3 | |||
| Reference Input Range | 2.2 | 2.6 | V | 4 | |||
| Reference Input Impedance | 3.2 | kΩ | 4 | ||||
| Reference Input Capacitance | 10 | pF | 4 | ||||
| Maximum Signal Level (CH0+, CH0-, CH1+, CH1- to AGND) | -1 | 1 | V | CH0+,CH0-,CH1+,CH1- to AGND | 4 | ||
| Differential Input Voltage Range Channel 1 | -660 | 660 | mV | 4 | |||
| Analog Input Impedance | 390 | kΩ | Proportional to 1/MCLK frequency | 4 | |||
| Oscillator Input Frequency Range (MCLK) | MCLK | 1 | 4 | MHz | 4 | ||
| Operating Voltage | 4.5 | 5.5 | V | AVDD, DVDD | 4 | ||
| Analog Supply Current | IDD,A | 2.7 | 3 | mA | AVDD pin only | 4 | |
| Digital Supply Current | IDD,D | 1.2 | 2 | mA | DVDD pin only | 4 | |
| Specified Temperature Range | TA | -40 | 85 | °C | 4 | ||
| Supply voltage VDD | VDD | 7 | V | 3 | |||
| Digital inputs and outputs w.r.t. AGND (minimum) | -0.6 | V | 3 | ||||
| Analog input w.r.t. AGND | -6 | 6 | V | 3 | |||
| VREF input w.r.t. AGND (minimum) | -0.6 | V | 3 | ||||
| Ambient temperature with power applied | -65 | 125 | °C | 3 | |||
| Storage temperature | -65 | 150 | °C | 3 | |||
| Soldering temperature of leads | 300 | °C | 10 seconds | 3 | |||
| ESD on the analog inputs (HBM) | 5 | kV | HBM | 3 | |||
| ESD on the analog inputs (MM) | 500 | V | MM | 3 | |||
| ESD on all other pins (HBM) | 5 | kV | HBM | 3 | |||
| ESD on all other pins (MM) | 500 | V | MM | 3 | |||
| FOUT0 and FOUT1 Output High Voltage | VOH | 4.5 | V | VIOH = 10 mA, DVDD = 5.0V | 5 | ||
| FOUT0 and FOUT1 Output Low Voltage | VOL | 0.5 | V | IOL = 10 mA, DVDD = 5.0V | 5 | ||
| HFOUT Output High Voltage | VOH | 4 | V | VIOH = 5 mA, DVDD = 5.0V | 5 | ||
| HFOUT Output Low Voltage | VOL | 0.5 | V | IOL = 5 mA, DVDD = 5.0V | 5 | ||
| High-Level Input Voltage (all digital input pins) | VIH | 2.4 | V | DVDD = 5.0V | 5 | ||
| Low-Level Input Voltage (all digital input pins) | VIL | 0.85 | V | DVDD = 5.0V | 5 | ||
| Input Leakage Current | -3 | 3 | µA | VIN = 0, VIN = DVDD | 5 | ||
| Pin Capacitance | 10 | pF | Note 3 | 5 |
CAD (KiCad official)
- Symbol:
MCP3905A-I - Footprint:
Package_SO:SSOP-24_5.3x8.2mm_P0.65mm - 3D model: SSOP-24-208mil (KiCad packages3D, STEP)
- 3D model files:
mcp3905a-i-ss-etched.step/mcp3905a-i-ss-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp3905a-i-ss.step/mcp3905a-i-ss.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (32 pp, sha256
9b5d77f773b4132f, retrieved 2026-11-11, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).