3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownMCP3421A2T-E
Microchip Tech · Analog To Digital Converters (ADCs) · SOT-23-6
MCP3421A2T-E from Microchip Tech, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN+ | power_in | Positive differential analog input; the converted voltage is VIN+ minus VIN-, the differential input should not exceed VREF/PGA (2.048 V/PGA) for accurate measurement, and each analog pin is specified from VSS-0.3 V to VDD+0.3 V. |
| 2 | VSS | power_in | Ground pin and current return path of the device, which must be connected to a ground plane through a low-impedance connection. |
| 3 | SCL | input | I2C serial clock input that accepts only external clocks from the master; it is an open-drain N-channel driver and needs a pull-up resistor from VDD. |
| 4 | SDA | bidirectional | I2C serial data pin used for conversion read-out and configuration writes; it is an open-drain N-channel driver needing a pull-up resistor from VDD (typically 5 kΩ to 10 kΩ for standard and fast modes, less than 1 kΩ for high-speed mode, which is not recommended below VDD = 2.7 V). |
| 5 | VDD | power_in | Positive supply pin that must be maintained within 2.7 V to 5.5 V for specified operation and bypassed with about 0.1 µF ceramic plus 10 µF tantalum to ground. |
| 6 | VIN- | power_in | Negative differential analog input that can be tied to VSS for single-ended operation, with each analog pin specified from VSS-0.3 V to VDD+0.3 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOT-23-6 |
| Category | Data Converters |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Resolution and No Missing Codes (DR = 240 SPS) | 12 | bits | DR = 240 SPS | 3 | |||
| Resolution and No Missing Codes (DR = 60 SPS) | 14 | bits | DR = 60 SPS | 3 | |||
| Resolution and No Missing Codes (DR = 15 SPS) | 16 | bits | DR = 15 SPS | 3 | |||
| Resolution and No Missing Codes (DR = 3.75 SPS) | 18 | bits | DR = 3.75 SPS | 3 | |||
| Data Rate (12 bits mode) | DR | 176 | 240 | 328 | SPS | S1,S0 = '00', (12 bits mode) | 3 |
| Data Rate (14 bits mode) | DR | 44 | 60 | 82 | SPS | S1,S0 = '01', (14 bits mode) | 3 |
| Data Rate (16 bits mode) | DR | 11 | 15 | 20.5 | SPS | S1,S0 = '10', (16 bits mode) | 3 |
| Data Rate (18 bits mode) | DR | 2.75 | 3.75 | 5.1 | SPS | S1,S0 = '11', (18 bits mode) | 3 |
| Integral Nonlinearity | INL | 10 | 35 | ppm of FSR | DR = 3.75 SPS | 3 | |
| Gain Error | 0.05 | 0.35 | % | PGA = 1, DR = 3.75 SPS | 4 | ||
| Offset Error | VOS | 15 | 40 | µV | Tested at PGA = 1; VDD = 5.0V and DR = 3.75 SPS | 4 | |
| Voltage Range (VDD) | VDD | 2.7 | 5.5 | V | 4 | ||
| Supply Current during Conversion | IDDA | 155 | 190 | µA | VDD = 5.0V | 4 | |
| Supply Current during Standby Mode | IDDS | 0.1 | 0.5 | µA | 4 | ||
| Low level output voltage | VOL | 0.4 | V | IOL = 3 mA, VDD = +5.0V | 4 | ||
| Supply Current when I2C bus line is active | IDDB | 10 | µA | 4 | |||
| Input Leakage Current (high) | IILH | 1 | µA | VIH = 5.5V | 4 | ||
| Input Leakage Current (low) | IILL | -1 | µA | VIL = GND | 4 | ||
| Pin capacitance | CPIN | 10 | pF | 4 | |||
| I2C Bus Capacitance | Cb | 400 | pF | 4 | |||
| Specified Temperature Range | TA | -40 | 85 | °C | 5 | ||
| Operating Temperature Range | TA | -40 | 125 | °C | 5 | ||
| Storage Temperature Range | TA | -65 | 150 | °C | 5 | ||
| Thermal Resistance, 6L SOT-23 | θJA | 190.5 | °C/W | 5 | |||
| VDD supply voltage | VDD | 7 | V | 3 | |||
| Voltage on all inputs and outputs w.r.t VSS (minimum) | -0.3 | V | 3 | ||||
| Current at Input Pins | -2 | 2 | mA | 3 | |||
| Current at Output and Supply Pins | -10 | 10 | mA | 3 | |||
| Storage Temperature | -65 | 150 | °C | 3 | |||
| Ambient Temp. with power applied | -55 | 125 | °C | 3 | |||
| ESD protection on all pins (HBM) | 6 | kV | HBM | 3 | |||
| ESD protection on all pins (MM) | 400 | V | MM | 3 | |||
| Maximum Junction Temperature (TJ) | TJ | 150 | °C | 3 |
CAD (KiCad official)
- Symbol:
MCP3421A2T-E - Footprint:
Package_TO_SOT_SMD:SOT-23-6 - 3D model: SOT-23-6 (KiCad packages3D, STEP)
- 3D model files:
mcp3421a2t-e-etched.step/mcp3421a2t-e-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp3421a2t-e.step/mcp3421a2t-e.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (42 pp, sha256
5249b67ed71256bc, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).