main
Ray
mcp2036-i-sl: renamed from mcp2036-i, the part it was built from (MCP2036-I/SL); family listed
f191ef7
MCP2036-I/SL
Microchip Tech · Touch Sensors · SOIC-14
MCP2036-I from Microchip Tech, in a SOIC-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VREF | power_in | Mid-scale voltage reference output (VDD/2) that needs a load capacitor between 100 nF and 1 µF located close to the pin. |
| 2 | LREF | input | Reference inductor input, which should be AC coupled to the coil through a 10 nF ceramic capacitor. |
| 3 | LBTN | input | Active (sensor) inductor input, which should be AC coupled to the coil through a 10 nF ceramic capacitor. |
| 4 | VDD | power_in | Power supply for the analog and digital circuitry, to be maintained in the 2.7V to 5.5V range with a 100 nF bypass capacitor. |
| 5 | DRVOUT | output | Current-mode driver output used to excite the sensor coils, designed to drive small inductive loads. |
| 6 | DRVIN | input | Analog input to the coil driver, whose triangular waveform should be in phase with the clock signal for best performance. |
| 7 | CLK | input | External clock input used for synchronous detection and to generate the triangular drive waveform, with an input clock frequency of 2 MHz typical. |
| 8 | REFSEL | input | Digital input that selects between the reference and sensor coil inputs (LREF and LBTN). |
| 9 | CS | input | Active-low chip select; a logic-low fully enables the circuit and a logic-high puts it into low-power mode. |
| 10 | ISOL | input | Digital detector isolation input; pulling it high isolates the op amp from the coil inputs and pulling it low reconnects them. |
| 11 | VSS | power_in | Ground pin and the current return path for both analog and digital circuitry. |
| 12 | VDETOUT | output | Detector output voltage, a low-impedance analog output intended for driving the microcontroller ADC. |
| 13 | VDET- | input | Inverting input of the output detector amplifier, connected to the mixer output through an internal 10 kΩ resistor. |
| 14 | VDET+ | input | Non-inverting input of the output detector amplifier, connected to the mixer output through an internal 10 kΩ resistor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-14 |
| Category | Sensors |
| Pins | 14 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VDD | 2.7 | 5.5 | V | 11 | ||
| Voltage on VDD with respect to VSS | VDD | -0.3 | 6.5 | V | 11 | ||
| Ambient temperature under bias | -40 | 125 | °C | 11 | |||
| Storage temperature | -65 | 150 | °C | 11 | |||
| Current at Output and Supply Pins | -30 | 30 | mA | 11 | |||
| Voltage on all other pins with respect to VSS | -0.3 | V | max printed as (VDD + 0.3V) | 11 | |||
| Maximum Junction Temperature | 150 | °C | 11 | ||||
| DC Open Loop Gain | AOL | 90 | 110 | dB | 11 | ||
| Common Mode Rejection Ratio | CMMR | 60 | 76 | dB | 11 | ||
| Input Offset Voltage | VOS | -7 | 7 | mV | 11 | ||
| Input Bias Current | IB | -20 | 20 | pA | (Note 1) | 11 | |
| Input Bias Current | IB | -1 | 1 | nA | (Note 1) | 11 | |
| Input Offset Current | IOS | -1 | 1 | pA | (Note 1) | 11 | |
| Input Pins Leakage Current | ILKG | -100 | 100 | nA | CS, CLK, REFSEL, LREF, LBTN | 11 | |
| Power Supply Rejection Ratio (coil driver) | PSRR | 60 | dB | 12 | |||
| Maximum Output Capacitance | COUT | 1 | µF | (Note 1) | 12 | ||
| Input Bias/Leakage Current | IB | -20 | 20 | pA | T = 85°C (Note 1) | 12 | |
| Input Bias/Leakage Current | IB | -1 | 1 | nA | T = 125°C (Note 1) | 12 | |
| Device Turn-On Time | tON | 4 | 10 | µs | Time from CS= 0 to valid VDETOUT output (Note 1) | 13 | |
| Industrial Temperature Range | TA | -40 | 85 | °C | 13 | ||
| Thermal Resistance, 14L-SOIC | θJA | 120 | °C/W | 13 |
CAD (KiCad official)
- Symbol:
MCP2036-I - Footprint:
Package_SO:SOIC-14_3.9x8.7mm_P1.27mm - 3D model: SOIC-14 (KiCad packages3D, STEP)
- 3D model files:
mcp2036-i-etched.step/mcp2036-i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp2036-i.step/mcp2036-i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (30 pp, sha256
86e5ed27763caaf2, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
Other parts in this family
This page is MCP2036-I/SL. These part numbers share its family name but are different parts (another package, rating or grade), each with its own page:
- MCP2036-I/MG
# MCP2036-I/SL
**Microchip Tech** · Touch Sensors · SOIC-14
MCP2036-I from Microchip Tech, in a SOIC-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VREF | power_in | Mid-scale voltage reference output (VDD/2) that needs a load capacitor between 100 nF and 1 µF located close to the pin. |
| 2 | LREF | input | Reference inductor input, which should be AC coupled to the coil through a 10 nF ceramic capacitor. |
| 3 | LBTN | input | Active (sensor) inductor input, which should be AC coupled to the coil through a 10 nF ceramic capacitor. |
| 4 | VDD | power_in | Power supply for the analog and digital circuitry, to be maintained in the 2.7V to 5.5V range with a 100 nF bypass capacitor. |
| 5 | DRVOUT | output | Current-mode driver output used to excite the sensor coils, designed to drive small inductive loads. |
| 6 | DRVIN | input | Analog input to the coil driver, whose triangular waveform should be in phase with the clock signal for best performance. |
| 7 | CLK | input | External clock input used for synchronous detection and to generate the triangular drive waveform, with an input clock frequency of 2 MHz typical. |
| 8 | REFSEL | input | Digital input that selects between the reference and sensor coil inputs (LREF and LBTN). |
| 9 | CS | input | Active-low chip select; a logic-low fully enables the circuit and a logic-high puts it into low-power mode. |
| 10 | ISOL | input | Digital detector isolation input; pulling it high isolates the op amp from the coil inputs and pulling it low reconnects them. |
| 11 | VSS | power_in | Ground pin and the current return path for both analog and digital circuitry. |
| 12 | VDETOUT | output | Detector output voltage, a low-impedance analog output intended for driving the microcontroller ADC. |
| 13 | VDET- | input | Inverting input of the output detector amplifier, connected to the mixer output through an internal 10 kΩ resistor. |
| 14 | VDET+ | input | Non-inverting input of the output detector amplifier, connected to the mixer output through an internal 10 kΩ resistor. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | SOIC-14 |
| Category | Sensors |
| Pins | 14 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage | VDD | 2.7 | | 5.5 | V | | 11 |
| Voltage on VDD with respect to VSS | VDD | -0.3 | | 6.5 | V | | 11 |
| Ambient temperature under bias | | -40 | | 125 | °C | | 11 |
| Storage temperature | | -65 | | 150 | °C | | 11 |
| Current at Output and Supply Pins | | -30 | | 30 | mA | | 11 |
| Voltage on all other pins with respect to VSS | | -0.3 | | | V | max printed as (VDD + 0.3V) | 11 |
| Maximum Junction Temperature | | | | 150 | °C | | 11 |
| DC Open Loop Gain | AOL | 90 | 110 | | dB | | 11 |
| Common Mode Rejection Ratio | CMMR | 60 | 76 | | dB | | 11 |
| Input Offset Voltage | VOS | -7 | | 7 | mV | | 11 |
| Input Bias Current | IB | -20 | | 20 | pA | (Note 1) | 11 |
| Input Bias Current | IB | -1 | | 1 | nA | (Note 1) | 11 |
| Input Offset Current | IOS | -1 | | 1 | pA | (Note 1) | 11 |
| Input Pins Leakage Current | ILKG | -100 | | 100 | nA | CS, CLK, REFSEL, LREF, LBTN | 11 |
| Power Supply Rejection Ratio (coil driver) | PSRR | 60 | | | dB | | 12 |
| Maximum Output Capacitance | COUT | | | 1 | µF | (Note 1) | 12 |
| Input Bias/Leakage Current | IB | -20 | | 20 | pA | T = 85°C (Note 1) | 12 |
| Input Bias/Leakage Current | IB | -1 | | 1 | nA | T = 125°C (Note 1) | 12 |
| Device Turn-On Time | tON | | 4 | 10 | µs | Time from CS= 0 to valid VDETOUT output (Note 1) | 13 |
| Industrial Temperature Range | TA | -40 | | 85 | °C | | 13 |
| Thermal Resistance, 14L-SOIC | θJA | | 120 | | °C/W | | 13 |
## CAD (KiCad official)
- Symbol: `MCP2036-I`
- Footprint: `Package_SO:SOIC-14_3.9x8.7mm_P1.27mm`
- 3D model: SOIC-14 (KiCad packages3D, STEP)
- 3D model files: `mcp2036-i-etched.step` / `mcp2036-i-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mcp2036-i.step` / `mcp2036-i.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/mcp2036-i-datasheet.pdf) (30 pp, sha256 `86e5ed27763caaf2`, retrieved 2026-11-02, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mcp2036-i-datasheet.pdf)
## Other parts in this family
This page is **MCP2036-I/SL**. These part numbers share its family name but are different parts (another package, rating or grade), each with its own page:
- MCP2036-I/MG