Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MCP19035-BAABE

Microchip Tech · DC-DC Controllers · DFN-10-EP(3x3)

MCP19035-BAABE from Microchip Tech, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 SHDN input Device shutdown input: logic High enables the device, logic Low disables it with LDRV and HDRV held low and the internal LDO off, and the pin must not float (connect to VIN through 100 kΩ if unused).
2 FB input Feedback voltage input, the negative input of the internal error amplifier, used to sense the output voltage against the internal reference.
3 COMP output Internal error amplifier output, with the compensation network connected between this pin and FB.
4 VIN power_in Input power pin for the controller that feeds the internal LDO generating the +5V VCC, requiring a bypass capacitor between VIN and GND.
5 PWRGD output Open-drain power good output, pulled low when the output is 90% less than the typical value, with a recommended 100 kΩ pull-up to +VCC.
6 +VCC power_out LDO output providing +5.0V for internal circuitry; the sum of external load and internal current should not exceed 50 mA, with a 4.7 μF ceramic capacitor to GND.
7 LDRV output Low-side N-channel MOSFET (synchronous rectifier) gate drive output capable of sourcing 1A and sinking 1.5A.
8 BOOT power_out Floating bootstrap supply for the high-side gate driver; a capacitor between BOOT and PHASE supplies the charge to turn on the external high-side MOSFET.
9 PHASE passive Switching node pin that returns the high-side gate driver, provides the BOOT capacitor charging path, and senses the switching transition to eliminate cross conduction.
10 HDRV output High-side N-channel MOSFET (control transistor) gate drive output capable of sourcing and sinking 1A.
11 EP power_in Exposed thermal pad to which analog ground and power ground are both connected; it must be connected to GND.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package DFN-10-EP(3x3)
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Voltage Range VIN 4.5 30 V 3
UVLO (VIN Rising) UVLOON 4 4.2 4.4 V 3
UVLO (VIN Falling) UVLOOFF 3.4 3.6 3.8 V 3
Input Quiescent Current I(VIN) 6 8 mA 3
Shutdown Current IIN_SHDN 25 50 µA SHDN = GND. Internal Voltage Regulator is also disabled 3
Linear Regulator Output Voltage VCC 4.875 5 5.125 V 6V ≤ VIN < 30V 3
Output Current IVCC-OUT 50 mA 6.5V ≤ VIN < 30V, Note 2 3
Short-Circuit Output Current IVCC-OUT_SC 100 mA VIN = 6V, RLOAD < 0.1 3
Dropout Voltage 0.75 1.3 V IVCC_OUT = 50 mA 3
Switching Frequency (300 kHz option) FSW 255 300 345 kHz 2 options, see Section 4.4, Internal Oscillator 3
Switching Frequency (600 kHz option) FSW 510 600 690 kHz 2 options, see Section 4.4, Internal Oscillator 3
Ramp Signal Amplitude VRAMP 0.9 1 1.1 VPP Note 1 3
Reference Voltage Generator VREF 585 600 615 mV 3
Gain Bandwidth Product GBP 6.5 10 MHz Note 1 4
Open Loop Gain AOL 70 80 dB Note 1 4
Input Offset Voltage VOS -5 0.1 5 mV Note 1 4
Input Bias Current (FB Pin) IBIAS 5 nA Note 1 4
Maximum Duty Cycle DCMAX 85 % 4
Minimum ON time tON(MIN) 50 100 ns 6V ≤ VIN < 30V, Note 1 4
Logic Low-to-High Threshold SHDNHI 0.85 V 4.5V ≤ VIN < 30V, VCC goes from 0V to 5V 4
Logic High-to-Low Threshold SHDNLO 0.4 V 4.5V ≤ VIN < 30V, VCC goes from 5V to 0V 4
Power Good Threshold High PGTH-H 93 96 % of VREF 4
Power Good Threshold Low PGTH-LOW 88 90 % of VREF 4
High-Side Driver Pull-up Resistance RHI-SOURCE 2 3.5 ohm VBOOT -VPHASE = 4.5V, IHDRV = 100 mA, Note 1 4
High-Side Driver Pull-Down Resistance RHI-SINK 2 3.5 ohm VBOOT -VPHASE = 4.5V, IHDRV = 100 mA, Note 1 4
Low-Side Driver Pull-Up Resistance RLO-SOURCE 2 3.5 ohm VCC = 5V, Note 1 4
Low-Side Driver Pull-Down Resistance RLO-SINK 1 2.5 ohm VCC = 5V, Note 1 4
HDRV Rise Time tRH 15 35 ns CLOAD = 1.0 nF, Note 1 4
HDRV Fall Time tFH 15 35 ns CLOAD = 1.0 nF, Note 1 4
LDRV Rise Time tRL 10 25 ns CLOAD = 1.0 nF, Note 1 4
LDRV Fall Time tFL 10 25 ns CLOAD = 1.0 nF, Note 1 5
Dead Time tDT 20 ns Two Dead-Time options, see Section 5.2.2, Dead Time Selection, Note 1 5
High-Side Over Current Threshold Voltage OCTH-HI 430 480 530 mV Note 1, VCBOOT = 5V 5
Low-Side Over Current Threshold Voltage OCTH-LO 130 180 230 mV Note 1, Note 3 5
Off-Time Between Restart Attempts (Hick-Up Time) tSS-HT 30 60 ms Note 1 5
Specified Temperature Range TA -40 125 °C 5
Maximum Junction Temperature TJ-MAX 150 °C 5
Operating Temperature Range TA -40 125 °C 5
Storage Temperature Range TA -65 150 °C 5
Input Voltage (VIN - VGND) VIN -0.3 32 V 3
Boot Voltage VBOOT -0.3 37 V 3
ESD protection on all pins (HBM) 2 kV 3

CAD (KiCad official)

  • Symbol: MCP19035-BAABE
  • Footprint: Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm
  • 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: mcp19035-baabe-etched.step / mcp19035-baabe-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp19035-baabe.step / mcp19035-baabe.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (44 pp, sha256 5ef9e980269ee409, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF