Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MCP1726T-3302E/SN

Microchip Tech · Linear Voltage Regulators (LDO) · SOIC-8

MCP1726T-3302E from Microchip Tech, in a SOIC-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Input voltage supply, operating over 2.3V to 6.0V; an input capacitor of 1 µF to 10 µF is recommended, especially if the source is several inches away or is a battery.
2 VIN power_in Input voltage supply, operating over 2.3V to 6.0V; the second VIN pin is bonded in parallel with pin 1.
3 SHDN input Active-low shutdown control: logic-high enables the LDO output, and logic-low disables it, which also drives PWRGD low and reduces quiescent current to a typical 0.1 µA.
4 GND power_in Ground connected to a quiet circuit ground; it conducts only the LDO quiescent current (typically 140 µA).
5 PWRGD output Open-drain power-good output that indicates when VOUT is within 92% (typical) of its nominal regulation value, with typical hysteresis of 0.7% for fixed outputs above 2.5V.
6 CDELAY input Power-up delay set-point input; an external capacitor to ground sets the PWRGD delay from 200 µs (no capacitance) up to 300 ms (0.1 µF).
7 VOUT power_out Regulated LDO output, rated for 1A minimum; a minimum output capacitance of 1.0 µF is required for stability.
8 VOUT power_out Regulated LDO output, rated for 1A minimum; the second VOUT pin is bonded in parallel with pin 7 and needs the same 1.0 µF minimum output capacitance.

Key specifications

Parameter Value
Manufacturer Microchip Tech
Package SOIC-8
Category Power Management
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Operating Voltage VIN 2.3 6 V Note 1 4
Input Quiescent Current Iq 140 220 µA IL = 0 mA, VIN =VR + 0.5V, VOUT = 0.8V to 5.0V 4
Input Quiescent Current for SHDN Mode ISHDN 0.1 3 µA SHDN = GND 4
Maximum Output Current IOUT 1 A VIN = 2.3V to 6.0V (Note 1) 4
Line Regulation VOUT/(VOUT x VIN) 0.05 0.3 %/V (VR + 0.5)V <= VIN <= 6V 4
Load Regulation VOUT/VOUT -1.5 0.5 1.5 % IOUT = 1 mA to 1A, VIN = (VR + 0.6)V (Note 4) 4
Voltage Regulation (fixed output, relative to VR) VOUT -2.5 2.5 % Note 2 4
Voltage Regulation typical tolerance VOUT -0.5 0.5 % Note 2 4
Dropout Voltage VIN -VOUT 220 500 mV IOUT = 1A, VIN(MIN) = 2.3V (Note 5) 4
Input Voltage Operating Range for Valid PWRGD (TA = +25°C) VPWRGD_VIN 1 6 V TA = +25°C 5
Input Voltage Operating Range for Valid PWRGD (TA = -40°C to +125°C) VPWRGD_VIN 1.2 6 V TA = -40°C to +125°C 5
PWRGD Threshold Voltage, falling edge (VOUT > 2.5V) PWRGD_THF 89 92 95 %VOUT VOUT > 2.5V, Falling Edge 5
PWRGD Threshold Voltage, rising edge (VOUT > 2.5V) PWRGD_THR 90 93 96 %VOUT VOUT > 2.5V, Rising Edge 5
PWRGD Output Voltage Low VPWRGD_L 0.2 0.4 V IPWRGD SINK = 1.2 mA 5
PWRGD Time Delay TPG 10 30 55 ms CDELAY = 0.01 µF 5
Shutdown Logic-High Input VSHDN-HIGH 45 %VIN VIN = 2.3V to 6.0V 5
Shutdown Logic-Low Input VSHDN-LOW 15 %VIN VIN = 2.3V to 6.0V 5
SHDN Input Leakage Current SHDNILK -0.1 0.001 0.1 µA VIN = 6V, SHDN = VIN, SHDN = GND 5
Operating Junction Temperature Range TJ -40 125 °C Steady State 6
Maximum Junction Temperature TJ 150 °C Transient 6
Storage Temperature Range TA -65 150 °C 6
Thermal Resistance, 8L SOIC, junction to air JA 163 °C/W 4-Layer JC51-7 Standard Board 6
Thermal Resistance, 8L SOIC, junction to case JC 42 °C/W 4-Layer JC51-7 Standard Board 6

CAD (KiCad official)

  • Symbol: MCP1726T-3302E
  • Footprint: Package_SO:SOIC-8_3.9x4.9mm_P1.27mm
  • 3D model: SOIC-8 (KiCad packages3D, STEP)
  • 3D model files: mcp1726t-3302e-etched.step / mcp1726t-3302e-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); mcp1726t-3302e.step / mcp1726t-3302e.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Microchip Tech datasheet (32 pp, sha256 913cb0f74fbdeae5, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF

Other parts in this family

This page is MCP1726T-3302E/SN. These part numbers share its family name but are different parts (another package, rating or grade), each with its own page:

  • MCP1726T-3302E/MF