main
Ray
Publish 0.1.0
4ebbd75
MCP1642D-33I
Microchip Tech · DC-DC Converters · MSOP-8
MCP1642D-33I from Microchip Tech, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Enable input: logic high (>75% of VIN) enables operation, logic low (<20% of VIN) disables the regulator; do not allow this pin to float. |
| 2 | NC | unconnected | Not connected (on fixed-VOUT options this position is NC; VFB exists only on the ADJ option). |
| 3 | PG | output | Open-drain Power Good output that can be pulled up to VOUT and turns low when VOUT drops below 10% of its nominal value. |
| 4 | VOUT | power_out | Boost converter output, connected to the integrated P-Channel MOSFET and the output capacitor. |
| 5 | SW | passive | Boost and rectifier switch node; connect the boost inductor between SW and VIN, carrying up to 1.8A peak inductor current. |
| 6 | PGND | power_in | Power ground return for the high-current N-Channel switch, connected externally to SGND. |
| 7 | SGND | power_in | Signal ground return for the integrated VREF and error amplifier, connected externally to PGND. |
| 8 | VIN | power_in | Input supply voltage pin requiring a local bypass capacitor of 4.7 µF minimum decoupled to GND. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-8 |
| Category | Power Supply Chip |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Start-Up Voltage | VIN | 0.65 | 0.8 | V | Note 1 | 3 | |
| Quiescent Current PWM Mode | IQPWM | 400 | 500 | µA | Measured at VOUT, EN = VIN, IOUT = 0 mA, Note 3 | 4 | |
| Output Voltage Accuracy (MCP1642B/D-33) | VOUT% | -3 | 3 | % | MCP1642B/D-33, VIN = 1.2V | 4 | |
| Line Regulation (MCP1642B/D-33) | VOUT/VOUT)/VIN/ | -0.5 | 0.01 | 0.5 | %/V | MCP1642B/D-33, VIN = 1.5V to 3.0V, IOUT = 25 mA | 4 |
| Load Regulation (MCP1642B/D-33) | VOUT/VOUT/ | -1.5 | 0.1 | 1.5 | % | MCP1642B/D-33, VIN = 1.5V, IOUT = 25 mA to 150 mA | 4 |
| Feedback Voltage | VFB | 1.173 | 1.21 | 1.247 | V | 3 | |
| Power Good Input Voltage Operating Range | VPG_VIN | 0.9 | 5.5 | V | ISINK = 5 mA, VFB = 0V, Note 5 | 5 | |
| Input Voltage Absolute Maximum (EN, FB, VIN, VSW, VOUT - GND) | 6.5 | V | 3 | ||||
| Output Current Bypass Mode | 800 | mA | 3 | ||||
| Operating Junction Temperature | -40 | 125 | °C | 3 | |||
| Ambient Temperature with Power Applied | -40 | 85 | °C | 3 | |||
| Storage Temperature | -65 | 150 | °C | 3 | |||
| ESD Protection HBM | 4 | kV | On all pins, HBM | 3 | |||
| ESD Protection MM | 300 | V | On all pins, MM | 3 | |||
| Operating Ambient Temperature Range | TA | -40 | 85 | °C | Steady State | 5 | |
| Maximum Junction Temperature | TJ | 150 | °C | Transient | 5 | ||
| Input Capacitor CIN | CIN | 4.7 | µF | Table 5-1 recommended range | 18 | ||
| Output Capacitor COUT | COUT | 10 | 100 | µF | Table 5-1 recommended range | 18 | |
| Inductance | L | 2.2 | 4.7 | 6.8 | µH | Recommended inductor range; 4.7 µH recommended | 18 |
| Thermal Resistance, 8L-MSOP | JA | 211 | °C/W | 5 |
CAD (KiCad official)
- Symbol:
MCP1642D-33I - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
mcp1642d-33i-etched.step/mcp1642d-33i-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp1642d-33i.step/mcp1642d-33i.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (32 pp, sha256
b4f111cdac10d1c3, retrieved 2026-11-09, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MCP1642D-33I
**Microchip Tech** · DC-DC Converters · MSOP-8
MCP1642D-33I from Microchip Tech, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | EN | input | Enable input: logic high (>75% of VIN) enables operation, logic low (<20% of VIN) disables the regulator; do not allow this pin to float. |
| 2 | NC | unconnected | Not connected (on fixed-VOUT options this position is NC; VFB exists only on the ADJ option). |
| 3 | PG | output | Open-drain Power Good output that can be pulled up to VOUT and turns low when VOUT drops below 10% of its nominal value. |
| 4 | VOUT | power_out | Boost converter output, connected to the integrated P-Channel MOSFET and the output capacitor. |
| 5 | SW | passive | Boost and rectifier switch node; connect the boost inductor between SW and VIN, carrying up to 1.8A peak inductor current. |
| 6 | PGND | power_in | Power ground return for the high-current N-Channel switch, connected externally to SGND. |
| 7 | SGND | power_in | Signal ground return for the integrated VREF and error amplifier, connected externally to PGND. |
| 8 | VIN | power_in | Input supply voltage pin requiring a local bypass capacitor of 4.7 µF minimum decoupled to GND. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-8 |
| Category | Power Supply Chip |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Start-Up Voltage | VIN | | 0.65 | 0.8 | V | Note 1 | 3 |
| Quiescent Current PWM Mode | IQPWM | | 400 | 500 | µA | Measured at VOUT, EN = VIN, IOUT = 0 mA, Note 3 | 4 |
| Output Voltage Accuracy (MCP1642B/D-33) | VOUT% | -3 | | 3 | % | MCP1642B/D-33, VIN = 1.2V | 4 |
| Line Regulation (MCP1642B/D-33) | VOUT/VOUT)/VIN/ | -0.5 | 0.01 | 0.5 | %/V | MCP1642B/D-33, VIN = 1.5V to 3.0V, IOUT = 25 mA | 4 |
| Load Regulation (MCP1642B/D-33) | VOUT/VOUT/ | -1.5 | 0.1 | 1.5 | % | MCP1642B/D-33, VIN = 1.5V, IOUT = 25 mA to 150 mA | 4 |
| Feedback Voltage | VFB | 1.173 | 1.21 | 1.247 | V | | 3 |
| Power Good Input Voltage Operating Range | VPG_VIN | 0.9 | | 5.5 | V | ISINK = 5 mA, VFB = 0V, Note 5 | 5 |
| Input Voltage Absolute Maximum (EN, FB, VIN, VSW, VOUT - GND) | | | | 6.5 | V | | 3 |
| Output Current Bypass Mode | | | | 800 | mA | | 3 |
| Operating Junction Temperature | | -40 | | 125 | °C | | 3 |
| Ambient Temperature with Power Applied | | -40 | | 85 | °C | | 3 |
| Storage Temperature | | -65 | | 150 | °C | | 3 |
| ESD Protection HBM | | | | 4 | kV | On all pins, HBM | 3 |
| ESD Protection MM | | | | 300 | V | On all pins, MM | 3 |
| Operating Ambient Temperature Range | TA | -40 | | 85 | °C | Steady State | 5 |
| Maximum Junction Temperature | TJ | | | 150 | °C | Transient | 5 |
| Input Capacitor CIN | CIN | 4.7 | | | µF | Table 5-1 recommended range | 18 |
| Output Capacitor COUT | COUT | 10 | | 100 | µF | Table 5-1 recommended range | 18 |
| Inductance | L | 2.2 | 4.7 | 6.8 | µH | Recommended inductor range; 4.7 µH recommended | 18 |
| Thermal Resistance, 8L-MSOP | JA | | 211 | | °C/W | | 5 |
## CAD (KiCad official)
- Symbol: `MCP1642D-33I`
- Footprint: `Package_SO:MSOP-8_3x3mm_P0.65mm`
- 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files: `mcp1642d-33i-etched.step` / `mcp1642d-33i-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mcp1642d-33i.step` / `mcp1642d-33i.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/mcp1642d-33i-datasheet.pdf) (32 pp, sha256 `b4f111cdac10d1c3`, retrieved 2026-11-09, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mcp1642d-33i-datasheet.pdf)