main
Ray
Publish 0.1.0
c6c1b45
MCP1252T-ADJI
Microchip Tech · DC-DC Converters · MSOP-8
MCP1252T-ADJI from Microchip Tech, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PGOOD | output | Open-drain power-good output that is high-impedance in regulation, asserts low when VOUT falls 7% (typ) below nominal, and is high-impedance when SHDN is low; connect to GND or leave unconnected if unused. |
| 2 | VOUT | power_out | Regulated output voltage (1.5V to 5.5V adjustable, VOUT(MAX) < 2 x VIN) that must be bypassed to GND with a filter capacitor. |
| 3 | VIN | power_in | Power supply input, 2.0V to 5.5V for the adjustable version, which should be tied to a ceramic bypass capacitor. |
| 4 | GND | power_in | Ground terminal that should be tied to a ground plane for best performance. |
| 5 | C- | passive | Flying capacitor negative terminal, which uses a low-ESR capacitor (1 µF recommended) to transfer charge from input to output. |
| 6 | C+ | passive | Flying capacitor positive terminal, where polarity must be observed if a polarized capacitor is used. |
| 7 | SHDN | input | Active-low shutdown input where logic low (VIL max 0.4V) disables the device and logic high (VIH min 1.4V) enables normal operation. |
| 8 | FB | input | Feedback input for the adjustable output where a resistor divider from VOUT sets VOUT = 1.21V x (1 + R1/R2), with VFB regulated at 1.21V typical. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-8 |
| Category | Power Management |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (Adjustable) | VIN | 2 | 5.5 | V | Adjustable Output - MCP1252-ADJ | 3 | |
| Output Voltage Adjustment Range | VOUT | 1.5 | 5.5 | V | VOUT(MAX) < 2 x VIN | 3 | |
| FB Regulation Voltage | VFB | 1.18 | 1.21 | 1.24 | V | MCP1252-ADJ, MCP1253-ADJ | 3 |
| Supply Current | IDD | 60 | 120 | µA | No load | 3 | |
| Shutdown Current | ISHDN | 0.1 | 2 | µA | SHDN = 0V | 3 | |
| SHDN Logic Input Voltage Low | VIL | 0.4 | V | 3 | |||
| SHDN Logic Input Voltage High | VIH | 1.4 | V | 3 | |||
| Internal Oscillator Frequency | FOSC | 520 | 650 | 780 | kHz | MCP1252 | 4 |
| Specified Temperature Range | TA | -40 | 85 | °C | "I" Temperature range | 4 | |
| Maximum Operating Junction Temperature | TJ | 125 | °C | 4 | |||
| Storage Temperature Range | TA | -65 | 150 | °C | 4 | ||
| Voltage on Any Pin w.r.t. GND | -0.3 | V | -0.3V to (VIN + 0.3V) | 3 | |||
| Storage Temperature Range (abs max) | -65 | 150 | °C | 3 | |||
| Ambient Temperature with Power Applied | -55 | 125 | °C | 3 | |||
| Junction Temperature | 150 | °C | 3 | ||||
| ESD Human Body Model | 4 | kV | 1.5 k in Series with 100 pF | 3 | |||
| ESD Machine Model | 400 | V | 200 pF, No Series Resistance | 3 | |||
| Output Short-Circuit Current | ISC | 200 | mA | VOUT = GND, foldback current | 3 | ||
| Power Efficiency | 81 | % | VIN = 3.0V, VOUT = 5V, IOUT =120 mA | 3 | |||
| Power Efficiency | 68 | % | VIN = 3.6V, VOUT = 5V, IOUT =120 mA | 3 | |||
| PGOOD Output Voltage | PGOOD_VOL | 0.01 | V | IPGOOD = 0.5 mA | 3 | ||
| Ripple Voltage | VRIP | 50 | mVp-p | MCP1252 | 4 | ||
| Thermal Resistance, 8 Pin MSOP | θJA | 206 | °C/W | Single-Layer SEMI G42-88 board, Natural Convection | 4 |
CAD (KiCad official)
- Symbol:
MCP1252T-ADJI - Footprint:
Package_SO:MSOP-8_3x3mm_P0.65mm - 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files:
mcp1252t-adji-etched.step/mcp1252t-adji-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mcp1252t-adji.step/mcp1252t-adji.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Microchip Tech datasheet (20 pp, sha256
e0157a8ec444a470, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MCP1252T-ADJI
**Microchip Tech** · DC-DC Converters · MSOP-8
MCP1252T-ADJI from Microchip Tech, in a MSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PGOOD | output | Open-drain power-good output that is high-impedance in regulation, asserts low when VOUT falls 7% (typ) below nominal, and is high-impedance when SHDN is low; connect to GND or leave unconnected if unused. |
| 2 | VOUT | power_out | Regulated output voltage (1.5V to 5.5V adjustable, VOUT(MAX) < 2 x VIN) that must be bypassed to GND with a filter capacitor. |
| 3 | VIN | power_in | Power supply input, 2.0V to 5.5V for the adjustable version, which should be tied to a ceramic bypass capacitor. |
| 4 | GND | power_in | Ground terminal that should be tied to a ground plane for best performance. |
| 5 | C- | passive | Flying capacitor negative terminal, which uses a low-ESR capacitor (1 µF recommended) to transfer charge from input to output. |
| 6 | C+ | passive | Flying capacitor positive terminal, where polarity must be observed if a polarized capacitor is used. |
| 7 | SHDN | input | Active-low shutdown input where logic low (VIL max 0.4V) disables the device and logic high (VIH min 1.4V) enables normal operation. |
| 8 | FB | input | Feedback input for the adjustable output where a resistor divider from VOUT sets VOUT = 1.21V x (1 + R1/R2), with VFB regulated at 1.21V typical. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Microchip Tech |
| Package | MSOP-8 |
| Category | Power Management |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply Voltage (Adjustable) | VIN | 2 | | 5.5 | V | Adjustable Output - MCP1252-ADJ | 3 |
| Output Voltage Adjustment Range | VOUT | 1.5 | | 5.5 | V | VOUT(MAX) < 2 x VIN | 3 |
| FB Regulation Voltage | VFB | 1.18 | 1.21 | 1.24 | V | MCP1252-ADJ, MCP1253-ADJ | 3 |
| Supply Current | IDD | | 60 | 120 | µA | No load | 3 |
| Shutdown Current | ISHDN | | 0.1 | 2 | µA | SHDN = 0V | 3 |
| SHDN Logic Input Voltage Low | VIL | | | 0.4 | V | | 3 |
| SHDN Logic Input Voltage High | VIH | 1.4 | | | V | | 3 |
| Internal Oscillator Frequency | FOSC | 520 | 650 | 780 | kHz | MCP1252 | 4 |
| Specified Temperature Range | TA | -40 | | 85 | °C | "I" Temperature range | 4 |
| Maximum Operating Junction Temperature | TJ | | | 125 | °C | | 4 |
| Storage Temperature Range | TA | -65 | | 150 | °C | | 4 |
| Voltage on Any Pin w.r.t. GND | | -0.3 | | | V | -0.3V to (VIN + 0.3V) | 3 |
| Storage Temperature Range (abs max) | | -65 | | 150 | °C | | 3 |
| Ambient Temperature with Power Applied | | -55 | | 125 | °C | | 3 |
| Junction Temperature | | | | 150 | °C | | 3 |
| ESD Human Body Model | | | | 4 | kV | 1.5 k in Series with 100 pF | 3 |
| ESD Machine Model | | | | 400 | V | 200 pF, No Series Resistance | 3 |
| Output Short-Circuit Current | ISC | | 200 | | mA | VOUT = GND, foldback current | 3 |
| Power Efficiency | | | 81 | | % | VIN = 3.0V, VOUT = 5V, IOUT =120 mA | 3 |
| Power Efficiency | | | 68 | | % | VIN = 3.6V, VOUT = 5V, IOUT =120 mA | 3 |
| PGOOD Output Voltage | PGOOD_VOL | | 0.01 | | V | IPGOOD = 0.5 mA | 3 |
| Ripple Voltage | VRIP | | 50 | | mVp-p | MCP1252 | 4 |
| Thermal Resistance, 8 Pin MSOP | θJA | | 206 | | °C/W | Single-Layer SEMI G42-88 board, Natural Convection | 4 |
## CAD (KiCad official)
- Symbol: `MCP1252T-ADJI`
- Footprint: `Package_SO:MSOP-8_3x3mm_P0.65mm`
- 3D model: MSOP-8 (KiCad packages3D, STEP)
- 3D model files: `mcp1252t-adji-etched.step` / `mcp1252t-adji-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mcp1252t-adji.step` / `mcp1252t-adji.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Microchip Tech datasheet](docs/mcp1252t-adji-datasheet.pdf) (20 pp, sha256 `e0157a8ec444a470`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mcp1252t-adji-datasheet.pdf)