Generated by kicad-footprint-generator · KiCad file format 20260206
MC9S08AC8CFJE
NXP Semicon · NXP MCU · LQFP-32(7x7)
MC9S08AC8CFJE from NXP Semicon, in a LQFP-32(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | IRQ/TPMCLK | input | External interrupt request input (IRQ) with software-selectable internal pull-up/pull-down, and it must not be driven above VDD because there is no clamp diode to VDD. |
| 2 | RESET | input | Dedicated active-low reset pin with internal pull-up, input hysteresis and a strong output driver (no slew-rate control), typically connected to the BDM header and an optional RC filter for EMC. |
| 3 | PTF4/TPM2CH0 | bidirectional | General-purpose I/O port F bit 4 (alternate function TPM2 channel 0), with software-selectable pull-up, slew-rate control and drive strength; reset state is high-impedance input. |
| 4 | PTF5/TPM2CH1 | bidirectional | General-purpose I/O port F bit 5 (alternate function TPM2 channel 1), with software-selectable pull-up, slew-rate control and drive strength; reset state is high-impedance input. |
| 5 | PTE0/TxD1 | bidirectional | General-purpose I/O port E bit 0 (alternate function SCI1 transmit TxD1), with software-selectable pull-up, slew-rate control and drive strength; reset state is high-impedance input. |
| 6 | PTE1/RxD1 | bidirectional | General-purpose I/O port E bit 1 (alternate function SCI1 receive RxD1), with software-selectable pull-up, slew-rate control and drive strength; reset state is high-impedance input. |
| 7 | PTE2/TPM1CH0 | bidirectional | General-purpose I/O port E bit 2 (alternate function TPM1 channel 0), with software-selectable pull-up, slew-rate control and drive strength; reset state is high-impedance input. |
| 8 | PTE3/TPM1CH1 | bidirectional | General-purpose I/O port E bit 3 (alternate function TPM1 channel 1), with software-selectable pull-up, slew-rate control and drive strength; reset state is high-impedance input. |
| 9 | PTE4/SS1 | bidirectional | General-purpose I/O port E bit 4 (alternate function SPI slave select SS1), with software-selectable pull-up, slew-rate control and drive strength; reset state is high-impedance input. |
| 10 | PTE5/MISO1 | bidirectional | General-purpose I/O port E bit 5 (alternate function SPI MISO1), with software-selectable pull-up, slew-rate control and drive strength; reset state is high-impedance input. |
| 11 | PTE6/MOSI1 | bidirectional | General-purpose I/O port E bit 6 (alternate function SPI MOSI1), with software-selectable pull-up, slew-rate control and drive strength; reset state is high-impedance input. |
| 12 | PTE7/SPSCK1 | bidirectional | General-purpose I/O port E bit 7 (alternate function SPI clock SPSCK1), with software-selectable pull-up, slew-rate control and drive strength; reset state is high-impedance input. |
| 13 | VSS | power_in | Primary ground pin for the I/O buffers and internal voltage regulator; the device has a second VSS pin that should connect to system ground or a low-impedance path to the main VSS. |
| 14 | VDD | power_in | Primary supply pin for the I/O buffers and internal voltage regulator, with absolute maximum rating of -0.3 V to 5.8 V, and a 0.1 µF ceramic bypass placed close to VDD/VSS is recommended. |
| 15 | PTG0/KBIP0 | bidirectional | General-purpose I/O port G bit 0 (alternate function keyboard interrupt KBIP0, falling-edge/low-level triggered), with software-selectable pull-up, slew-rate control and drive strength. |
| 16 | PTG1/KBIP1 | bidirectional | General-purpose I/O port G bit 1 (alternate function keyboard interrupt KBIP1, falling-edge/low-level triggered), with software-selectable pull-up, slew-rate control and drive strength. |
| 17 | PTB0/TPM3CH0/AD1P0 | bidirectional | General-purpose I/O port B bit 0 multiplexed with ADC channel AD0 and TPM3 channel 0; enabling it as an ADC input disables its digital I/O function, and TPM3 is not available on AW variants. |
| 18 | PTB1/TPM3CH1/AD1P1 | bidirectional | General-purpose I/O port B bit 1 multiplexed with ADC channel AD1 and TPM3 channel 1; enabling it as an ADC input disables its digital I/O function, and TPM3 is not available on AW variants. |
| 19 | PTB2/AD1P2 | bidirectional | General-purpose I/O port B bit 2 multiplexed with ADC channel AD2; enabling it as an ADC input disables its digital I/O function. |
| 20 | PTB3/AD1P3 | bidirectional | General-purpose I/O port B bit 3 multiplexed with ADC channel AD3; enabling it as an ADC input disables its digital I/O function. |
| 21 | VDDAD | power_in | Analog supply for the ADC module, which should be held at the same voltage as VDD and bypassed with a 0.1 µF ceramic capacitor placed as close to the pin as possible. |
| 22 | VSSAD | power_in | Analog ground for the ADC module, which should be connected to VSS (same voltage as the digital ground). |
| 23 | PTD2/AD1P10/KBIP5 | bidirectional | General-purpose I/O port D bit 2 multiplexed with ADC channel AD10 and keyboard interrupt KBIP5; the ADC takes priority over digital functions when both are enabled. |
| 24 | PTD3/AD1P11/KBIP6 | bidirectional | General-purpose I/O port D bit 3 multiplexed with ADC channel AD11 and keyboard interrupt KBIP6; the ADC takes priority over digital functions when both are enabled. |
| 25 | VREFH | power_in | ADC high reference voltage, which may be tied to VDDAD or driven externally between the minimum VDDAD specification and VDDAD, and must never exceed VDDAD. |
| 26 | VREFL | power_in | ADC low reference voltage, which is connected internally to VSSAD in this package and should be tied to VSSAD. |
| 27 | BKGD/MS | bidirectional | Background debug and mode-select pin: low at reset rising edge forces background debug mode, otherwise it is the BDC communication pin with internal pull-up, input hysteresis and no slew-rate control. |
| 28 | PTG5/XTAL | output | Oscillator output (XTAL) when the external crystal/resonator is enabled, otherwise general-purpose I/O port G bit 5 (the ICG sets its function, so the GPIO registers do not control it while the crystal is used). |
| 29 | PTG6/EXTAL | input | Oscillator/external clock input (EXTAL) when the external clock or crystal is enabled, otherwise general-purpose I/O port G bit 6; the oscillator is a Pierce type with low-power or high-gain mode selectable. |
| 30 | VSS | power_in | Secondary ground pin, which should be connected to system ground or to a low-impedance connection to the primary VSS pin. |
| 31 | PTC0/SCL1 | bidirectional | General-purpose I/O port C bit 0 (alternate function IIC clock SCL1), with software-selectable pull-up, slew-rate control and drive strength; when the IIC function is enabled it controls pin direction. |
| 32 | PTC1/SDA1 | bidirectional | General-purpose I/O port C bit 1 (alternate function IIC data SDA1), with software-selectable pull-up, slew-rate control and drive strength; when the IIC function is enabled it controls pin direction. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | NXP Semicon |
| Package | LQFP-32(7x7) |
| Category | Embedded Processors & Controllers |
| Pins | 32 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage (absolute maximum) | VDD | -0.3 | 5.8 | V | 258 | ||
| Input voltage | Vin | -0.3 | V | 258 | |||
| Single pin instantaneous maximum current (applies to all pins) | IDD | -25 | 25 | mA | 258 | ||
| Maximum current into VDD | IDD | 120 | mA | 258 | |||
| Storage temperature | Tstg | -55 | 150 | °C | 258 | ||
| Maximum junction temperature | TJ | 150 | °C | 258 | |||
| Operating temperature range (packaged) | TA | 0 | 70 | °C | Range TL to TH as printed in Table A-3; grade suffix not decoded in excerpt | 258 | |
| External TPM clock period | tTPMext | 4 | tcyc | Temperature range -40 to 125 ℃ | 274 | ||
| External clock high time | tclkh | 1.5 | tcyc | Temperature range -40 to 125 ℃ | 274 | ||
| External clock low time | tclkl | 1.5 | tcyc | Temperature range -40 to 125 ℃ | 274 | ||
| Input capture pulse width | tICPW | 1.5 | tcyc | Temperature range -40 to 125 ℃ | 274 | ||
| SPI cycle time (master) | tSCK | 2 | 2048 | tcyc | Master; 100 pF on all SPI pins; timing at 20%/70% VDD | 275 | |
| SPI cycle time (slave) | tSCK | 4 | tcyc | Slave; 100 pF on all SPI pins; timing at 20%/70% VDD | 275 | ||
| Data input setup time (master) | tSI(M) | 30 | ns | Master; 100 pF on all SPI pins | 275 | ||
| Data input setup time (slave) | tSI(S) | 30 | ns | Slave; 100 pF on all SPI pins | 275 | ||
| Data input hold time (master) | tHI(M) | 30 | ns | Master; 100 pF on all SPI pins | 275 | ||
| Data input hold time (slave) | tHI(S) | 30 | ns | Slave; 100 pF on all SPI pins | 275 | ||
| Slave access time | tA | 0 | 40 | ns | Slave; 100 pF on all SPI pins | 275 | |
| Slave disable time | tdis | 40 | ns | Slave; 100 pF on all SPI pins | 275 | ||
| Data output valid time (master) | tSO | 25 | ns | Master; 100 pF on all SPI pins | 276 | ||
| Data output valid time (slave) | tSO | 25 | ns | Slave; 100 pF on all SPI pins | 276 | ||
| Data output hold time (master) | tHO | -10 | ns | Master; 100 pF on all SPI pins | 276 | ||
| Data output hold time (slave) | tHO | -10 | ns | Slave; 100 pF on all SPI pins | 276 | ||
| Thermal resistance junction-to-ambient, 32-pin LQFP, 1s board | θJA | 85 | °C/W | 32-pin LQFP, 1s (single-layer board), natural convection | 258 | ||
| Thermal resistance junction-to-ambient, 32-pin LQFP, 2s2p board | θJA | 56 | °C/W | 32-pin LQFP, 2s2p (4-layer board), natural convection | 258 |
CAD (KiCad official)
- Symbol:
MC9S08AC8CFJE - Footprint:
Package_QFP:LQFP-32_7x7mm_P0.8mm - 3D model: LQFP-32(7x7) (KiCad packages3D, STEP)
- 3D model files:
mc9s08ac8cfje-etched.step/mc9s08ac8cfje-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mc9s08ac8cfje.step/mc9s08ac8cfje.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: NXP Semicon datasheet (296 pp, sha256
a02b13679de67119, retrieved 2026-10-30, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).