main
Ray
mc11s: laser-etched CAD + chip hero (factory 2.0.0 backfill)
72d0a46
MC11S
Mysentech · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · QFN-16(3x3)
MC11S from Mysentech, in a QFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCL | input | I2C serial clock input. Standard mode up to 400 kHz, fast mode up to 1000 kHz. Requires an external pull-up resistor to VDD. |
| 2 | SDA | bidirectional | I2C serial data line (bidirectional, open-drain). Requires an external pull-up resistor to VDD. |
| 3 | CLKIN | input | External counter clock input, 0.1 MHz to 50 MHz with 40-60% duty cycle. Tie to GND when the internal 2.4 MHz clock is selected via REF_CLK_SEL. |
| 4 | ADDR | input | I2C slave address select input. Ties the device address to one of the supported values depending on the logic level applied. |
| 5 | INTB | output | Interrupt / alert output, active low. Signals conversion-complete or alarm status depending on configuration. |
| 6 | SD | input | Shutdown-mode enable input. Tie to GND when not used; drive high to force the chip into shutdown for lowest current (~40 nA). |
| 7 | VDD | power_in | Supply voltage, 2.0 V to 5.5 V (absolute max 5.5 V). Typical measurement peak current 0.8 mA, average 2.6 µA @ 1 Hz sample rate. |
| 8 | GND | power_in | Device ground reference. |
| 9 | NC | unconnected | No connection. Leave floating. |
| 10 | NC | unconnected | No connection. Leave floating. |
| 11 | NC | unconnected | No connection. Leave floating. |
| 12 | VT | output | Analog negative-temperature-coefficient voltage output. Read externally by MCU ADC to derive die temperature for temperature compensation. |
| 13 | C1N | passive | Channel 1 differential capacitive sense input (negative). Connects to the reference/second sensing capacitor; measures up to 1000 pF, driver current up to 3.2 mA per channel. |
| 14 | C1P | passive | Channel 1 differential capacitive sense input (positive). Paired with C1N; typically used for the reference capacitor in differential mode. |
| 15 | C0P | passive | Channel 0 differential capacitive sense input (positive). Paired with C0N; typically used for the sensed (DUT) capacitor. |
| 16 | C0N | passive | Channel 0 differential capacitive sense input (negative). Paired with C0P for the sensed capacitor connection. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Mysentech |
| Package | QFN-16(3x3) |
| Category | PMIC |
| Pins | 16 |
Ordering variants
Same part, different packaging or reel option.
MC11SMC11TMC11L
CAD (KiCad official)
- Symbol:
MC11S - Footprint:
Package_DFN_QFN:MPS_QFN-16_3x3mm_P0.5mm - 3D model: QFN-16(3x3) (KiCad packages3D, STEP)
- 3D model files:
mc11s-etched.step/mc11s-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mc11s.step/mc11s.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Mysentech datasheet (33 pp, sha256
a3d0a31e473acd20, retrieved 2026-08-17, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor:
ds2sf(Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MC11S
**Mysentech** · Voltage Regulators - Linear, Low Drop Out (LDO) Regulators · QFN-16(3x3)
MC11S from Mysentech, in a QFN-16(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SCL | input | I2C serial clock input. Standard mode up to 400 kHz, fast mode up to 1000 kHz. Requires an external pull-up resistor to VDD. |
| 2 | SDA | bidirectional | I2C serial data line (bidirectional, open-drain). Requires an external pull-up resistor to VDD. |
| 3 | CLKIN | input | External counter clock input, 0.1 MHz to 50 MHz with 40-60% duty cycle. Tie to GND when the internal 2.4 MHz clock is selected via REF_CLK_SEL. |
| 4 | ADDR | input | I2C slave address select input. Ties the device address to one of the supported values depending on the logic level applied. |
| 5 | INTB | output | Interrupt / alert output, active low. Signals conversion-complete or alarm status depending on configuration. |
| 6 | SD | input | Shutdown-mode enable input. Tie to GND when not used; drive high to force the chip into shutdown for lowest current (~40 nA). |
| 7 | VDD | power_in | Supply voltage, 2.0 V to 5.5 V (absolute max 5.5 V). Typical measurement peak current 0.8 mA, average 2.6 µA @ 1 Hz sample rate. |
| 8 | GND | power_in | Device ground reference. |
| 9 | NC | unconnected | No connection. Leave floating. |
| 10 | NC | unconnected | No connection. Leave floating. |
| 11 | NC | unconnected | No connection. Leave floating. |
| 12 | VT | output | Analog negative-temperature-coefficient voltage output. Read externally by MCU ADC to derive die temperature for temperature compensation. |
| 13 | C1N | passive | Channel 1 differential capacitive sense input (negative). Connects to the reference/second sensing capacitor; measures up to 1000 pF, driver current up to 3.2 mA per channel. |
| 14 | C1P | passive | Channel 1 differential capacitive sense input (positive). Paired with C1N; typically used for the reference capacitor in differential mode. |
| 15 | C0P | passive | Channel 0 differential capacitive sense input (positive). Paired with C0N; typically used for the sensed (DUT) capacitor. |
| 16 | C0N | passive | Channel 0 differential capacitive sense input (negative). Paired with C0P for the sensed capacitor connection. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Mysentech |
| Package | QFN-16(3x3) |
| Category | PMIC |
| Pins | 16 |
## Ordering variants
Same part, different packaging or reel option.
- `MC11S`
- `MC11T`
- `MC11L`
## CAD (KiCad official)
- Symbol: `MC11S`
- Footprint: `Package_DFN_QFN:MPS_QFN-16_3x3mm_P0.5mm`
- 3D model: QFN-16(3x3) (KiCad packages3D, STEP)
- 3D model files: `mc11s-etched.step` / `mc11s-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mc11s.step` / `mc11s.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Mysentech datasheet](docs/mc11s-datasheet.pdf) (33 pp, sha256 `a3d0a31e473acd20`, retrieved 2026-08-17, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** `ds2sf` (Claude). Every pin and dimension is cited to a datasheet page; it refuses to fabricate.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mc11s-datasheet.pdf)