main
Ray
Publish 0.1.0
9587259
MB85RS256TYPNF-G-BCERE1
FUJITSU · FRAM · SOP-8
MB85RS256TYPNF-G-BCERE1 from FUJITSU, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS | input | Chip select input: when CS is high the device is deselected (standby), SO goes High-Z and other inputs are ignored; CS must be low before the op-code is input, and it is pulled up internally to VDD (RP 18 to 33 to 80 kΩ). |
| 2 | SO | tri_state | Serial data output for FeRAM array and status register data, which is clocked out on the SCK falling edge and is High-Z during standby or hold. |
| 3 | WP | input | Write-protect input that, together with WEL and WPEN, controls writing to the status register and protected blocks, and must be held fixed from before a WRSR command until the end of that command sequence. |
| 4 | VSS | power_in | Ground reference pin; all datasheet voltage parameters are based on VSS = 0 V. |
| 5 | SI | input | Serial data input for op-code, address and write data, sampled on the SCK rising edge with 5 ns minimum set-up and hold times. |
| 6 | SCK | input | Serial clock input with a maximum frequency of 33 MHz; SI is latched on the rising edge and SO is output on the falling edge. |
| 7 | HOLD | input | Active-low hold input that interrupts serial input/output without deselecting the chip while CS is low; SO goes High-Z and SCK and SI become do not care. |
| 8 | VDD | power_in | Supply voltage pin; operating range is 1.8 V to 3.6 V (3.3 V typical) referenced to VSS. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FUJITSU |
| Package | SOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power supply voltage (absolute maximum) | VDD | -0.5 | 4 | V | VSS = 0 V (footnote *) | 13 | |
| Input voltage (absolute maximum) | VIN | -0.5 | V | VSS = 0 V (footnote *); printed max is VDD + 0.5 (<= 4.0) | 13 | ||
| Output voltage (absolute maximum) | VOUT | -0.5 | V | VSS = 0 V (footnote *); printed max is VDD + 0.5 (<= 4.0) | 13 | ||
| Operation ambient temperature (absolute maximum) | TA | -40 | 125 | C | 13 | ||
| Storage temperature | Tstg | -55 | 150 | C | 13 | ||
| Power supply voltage (recommended) | VDD | 1.8 | 3.3 | 3.6 | V | VSS = 0 V (footnote *1) | 13 |
| Operation ambient temperature (recommended) | TA | -40 | 125 | C | Ambient temperature when only this device is working (footnote *2) | 13 | |
| Input leakage current CS | /ILI/ | 200 | μA | 0 ≤ CS < VDD | 14 | ||
| Input leakage current CS | /ILI/ | 1 | μA | CS = VDD, 25 C | 14 | ||
| Input leakage current CS | /ILI/ | 2 | μA | CS = VDD, 125 C | 14 | ||
| Input leakage current WP, HOLD, SCK, SI | /ILI/ | 1 | μA | 0 V to VDD, 25 C | 14 | ||
| Input leakage current WP, HOLD, SCK, SI | /ILI/ | 2 | μA | 0 V to VDD, 125 C | 14 | ||
| Output leakage current SO | /ILO/ | 1 | μA | SO = 0 V to VDD, 25 C | 14 | ||
| Output leakage current SO | /ILO/ | 2 | μA | SO = 0 V to VDD, 125 C | 14 | ||
| Operating power supply current | IDD | 2.3 | mA | SCK = 33 MHz | 14 | ||
| Standby current | ISB | 50 | μA | SCK, SI, CS, WP, HOLD at VDD | 14 | ||
| Sleep current | IZZ | 12 | μA | CS = VDD; all inputs VSS or VDD | 14 | ||
| Input low voltage | VIL | -0.5 | V | VDD = 1.8 V to 3.6 V | 14 | ||
| Output low voltage | VOL | 0.4 | V | IOL = 2 mA | 14 | ||
| Pull up resistance for CS | RP | 18 | 33 | 80 | kΩ | 14 | |
| SCK clock frequency | fCK | 0 | 33 | MHz | AC test condition: VDD 1.8 V to 3.6 V, -40 C to +125 C | 15 | |
| Clock high time | tCH | 13 | ns | 15 | |||
| Clock low time | tCL | 13 | ns | 15 | |||
| Chip select set up time | tCSU | 10 | ns | 15 | |||
| Chip select hold time | tCSH | 10 | ns | 15 | |||
| Output disable time | tOD | 16 | ns | 15 | |||
| Output data valid time | tODV | 13 | ns | 15 | |||
| Output hold time | tOH | 0 | ns | 15 | |||
| Deselect time | tD | 40 | ns | 15 | |||
| Data in rising time | tR | 50 | ns | 15 | |||
| Data falling time | tF | 50 | ns | 15 | |||
| Data set up time | tSU | 5 | ns | 15 | |||
| Data hold time | tH | 5 | ns | 15 | |||
| HOLD set up time | tHS | 10 | ns | 15 | |||
| HOLD hold time | tHH | 10 | ns | 15 | |||
| HOLD output floating time | tHZ | 20 | ns | 15 | |||
| HOLD output active time | tLZ | 20 | ns | 15 | |||
| SLEEP recovery time | tREC | 400 | μs | 15 | |||
| Output capacitance | CO | 8 | pF | VDD = 3.3 V, VIN = VOUT = 0 V to VDD, f = 1 MHz, TA = +25 C | 16 | ||
| Input capacitance | CI | 6 | pF | 16 | |||
| CS level hold time at power OFF | tpd | 400 | ns | 18 | |||
| CS level hold time at power ON | tpu | 250 | μs | 18 | |||
| Power supply rising time | tr | 0.05 | ms/V | 18 | |||
| Power supply falling time | tf | 0.1 | ms/V | 18 | |||
| Data Retention | 3.38 | Years | Operation Ambient Temperature TA <= 125 C (footnote *3: under evaluation for more than 3.38 years at +125 C) | 18 | |||
| Data Retention | 10.9 | Years | Operation Ambient Temperature TA <= 105 C | 18 | |||
| Data Retention | 40.2 | Years | Operation Ambient Temperature TA <= 85 C | 18 |
CAD (KiCad official)
- Symbol:
MB85RS256TYPNF-G-BCERE1 - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
mb85rs256typnf-g-bcere1-etched.step/mb85rs256typnf-g-bcere1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);mb85rs256typnf-g-bcere1.step/mb85rs256typnf-g-bcere1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: FUJITSU datasheet (40 pp, sha256
e494e9284f8e9da7, retrieved 2026-10-30, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MB85RS256TYPNF-G-BCERE1
**FUJITSU** · FRAM · SOP-8
MB85RS256TYPNF-G-BCERE1 from FUJITSU, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CS | input | Chip select input: when CS is high the device is deselected (standby), SO goes High-Z and other inputs are ignored; CS must be low before the op-code is input, and it is pulled up internally to VDD (RP 18 to 33 to 80 kΩ). |
| 2 | SO | tri_state | Serial data output for FeRAM array and status register data, which is clocked out on the SCK falling edge and is High-Z during standby or hold. |
| 3 | WP | input | Write-protect input that, together with WEL and WPEN, controls writing to the status register and protected blocks, and must be held fixed from before a WRSR command until the end of that command sequence. |
| 4 | VSS | power_in | Ground reference pin; all datasheet voltage parameters are based on VSS = 0 V. |
| 5 | SI | input | Serial data input for op-code, address and write data, sampled on the SCK rising edge with 5 ns minimum set-up and hold times. |
| 6 | SCK | input | Serial clock input with a maximum frequency of 33 MHz; SI is latched on the rising edge and SO is output on the falling edge. |
| 7 | HOLD | input | Active-low hold input that interrupts serial input/output without deselecting the chip while CS is low; SO goes High-Z and SCK and SI become do not care. |
| 8 | VDD | power_in | Supply voltage pin; operating range is 1.8 V to 3.6 V (3.3 V typical) referenced to VSS. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | FUJITSU |
| Package | SOP-8 |
| Category | Memory |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Power supply voltage (absolute maximum) | VDD | -0.5 | | 4 | V | VSS = 0 V (footnote *) | 13 |
| Input voltage (absolute maximum) | VIN | -0.5 | | | V | VSS = 0 V (footnote *); printed max is VDD + 0.5 (<= 4.0) | 13 |
| Output voltage (absolute maximum) | VOUT | -0.5 | | | V | VSS = 0 V (footnote *); printed max is VDD + 0.5 (<= 4.0) | 13 |
| Operation ambient temperature (absolute maximum) | TA | -40 | | 125 | C | | 13 |
| Storage temperature | Tstg | -55 | | 150 | C | | 13 |
| Power supply voltage (recommended) | VDD | 1.8 | 3.3 | 3.6 | V | VSS = 0 V (footnote *1) | 13 |
| Operation ambient temperature (recommended) | TA | -40 | | 125 | C | Ambient temperature when only this device is working (footnote *2) | 13 |
| Input leakage current CS | /ILI/ | | | 200 | μA | 0 ≤ CS < VDD | 14 |
| Input leakage current CS | /ILI/ | | | 1 | μA | CS = VDD, 25 C | 14 |
| Input leakage current CS | /ILI/ | | | 2 | μA | CS = VDD, 125 C | 14 |
| Input leakage current WP, HOLD, SCK, SI | /ILI/ | | | 1 | μA | 0 V to VDD, 25 C | 14 |
| Input leakage current WP, HOLD, SCK, SI | /ILI/ | | | 2 | μA | 0 V to VDD, 125 C | 14 |
| Output leakage current SO | /ILO/ | | | 1 | μA | SO = 0 V to VDD, 25 C | 14 |
| Output leakage current SO | /ILO/ | | | 2 | μA | SO = 0 V to VDD, 125 C | 14 |
| Operating power supply current | IDD | | | 2.3 | mA | SCK = 33 MHz | 14 |
| Standby current | ISB | | | 50 | μA | SCK, SI, CS, WP, HOLD at VDD | 14 |
| Sleep current | IZZ | | | 12 | μA | CS = VDD; all inputs VSS or VDD | 14 |
| Input low voltage | VIL | -0.5 | | | V | VDD = 1.8 V to 3.6 V | 14 |
| Output low voltage | VOL | | | 0.4 | V | IOL = 2 mA | 14 |
| Pull up resistance for CS | RP | 18 | 33 | 80 | kΩ | | 14 |
| SCK clock frequency | fCK | 0 | | 33 | MHz | AC test condition: VDD 1.8 V to 3.6 V, -40 C to +125 C | 15 |
| Clock high time | tCH | 13 | | | ns | | 15 |
| Clock low time | tCL | 13 | | | ns | | 15 |
| Chip select set up time | tCSU | 10 | | | ns | | 15 |
| Chip select hold time | tCSH | 10 | | | ns | | 15 |
| Output disable time | tOD | | | 16 | ns | | 15 |
| Output data valid time | tODV | | | 13 | ns | | 15 |
| Output hold time | tOH | 0 | | | ns | | 15 |
| Deselect time | tD | 40 | | | ns | | 15 |
| Data in rising time | tR | | | 50 | ns | | 15 |
| Data falling time | tF | | | 50 | ns | | 15 |
| Data set up time | tSU | 5 | | | ns | | 15 |
| Data hold time | tH | 5 | | | ns | | 15 |
| HOLD set up time | tHS | 10 | | | ns | | 15 |
| HOLD hold time | tHH | 10 | | | ns | | 15 |
| HOLD output floating time | tHZ | | | 20 | ns | | 15 |
| HOLD output active time | tLZ | | | 20 | ns | | 15 |
| SLEEP recovery time | tREC | | | 400 | μs | | 15 |
| Output capacitance | CO | | | 8 | pF | VDD = 3.3 V, VIN = VOUT = 0 V to VDD, f = 1 MHz, TA = +25 C | 16 |
| Input capacitance | CI | | | 6 | pF | | 16 |
| CS level hold time at power OFF | tpd | 400 | | | ns | | 18 |
| CS level hold time at power ON | tpu | 250 | | | μs | | 18 |
| Power supply rising time | tr | 0.05 | | | ms/V | | 18 |
| Power supply falling time | tf | 0.1 | | | ms/V | | 18 |
| Data Retention | | 3.38 | | | Years | Operation Ambient Temperature TA <= 125 C (footnote *3: under evaluation for more than 3.38 years at +125 C) | 18 |
| Data Retention | | 10.9 | | | Years | Operation Ambient Temperature TA <= 105 C | 18 |
| Data Retention | | 40.2 | | | Years | Operation Ambient Temperature TA <= 85 C | 18 |
## CAD (KiCad official)
- Symbol: `MB85RS256TYPNF-G-BCERE1`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files: `mb85rs256typnf-g-bcere1-etched.step` / `mb85rs256typnf-g-bcere1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `mb85rs256typnf-g-bcere1.step` / `mb85rs256typnf-g-bcere1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [FUJITSU datasheet](docs/mb85rs256typnf-g-bcere1-datasheet.pdf) (40 pp, sha256 `e494e9284f8e9da7`, retrieved 2026-10-30, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/mb85rs256typnf-g-bcere1-datasheet.pdf)