Generated by kicad-footprint-generator · KiCad file format 20260206
MAX96714RGTJ
Analog Devices Inc./Maxim Integrated · Serializers, Deserializers · TQFN-32(5x5)
MAX96714RGTJ from Analog Devices Inc./Maxim Integrated, in a TQFN-32(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | MFP0 | bidirectional | Multifunction pin, MAX96714R functions are VS, FSYNC_OUT, DE/DV or GPIO0 (power-up default GPI0 with 1MΩ pull-down to ground). |
| 2 | MFP1 | bidirectional | Multifunction pin, GPIO1 on the MAX96714R (power-up default GPI1); pass-through I2C/UART is not present on the R. |
| 3 | MFP2 | bidirectional | Multifunction pin, FSYNC_OUT or GPIO2 on the MAX96714R (power-up default GPI2); MS and pass-through functions are not present on the R. |
| 4 | MFP3 | bidirectional | Primary I2C data pin (SDA) input/open-drain output with 40kΩ pull-up to VDDIO on the MAX96714R. |
| 5 | CFG0 | input | Configuration pin whose voltage is latched at power-up to select I2C device address (see Table 8); set by a resistor divider from VDDIO. |
| 6 | MFP4 | bidirectional | Primary I2C clock pin (SCL) input/open-drain output with 40kΩ pull-up to VDDIO on the MAX96714R. |
| 7 | MFP5 | bidirectional | Multifunction pin, default LOCK open-drain lock indication output with 40kΩ pull-up to VDDIO, or VS, DE/DV, GPIO5. |
| 8 | X1/OSC | input | Crystal/oscillator input; connect a 25MHz crystal, or connect an oscillator to X1. |
| 9 | X2 | passive | Crystal input for the other terminal of the 25MHz crystal; leave floating if an oscillator is used. |
| 10 | XRES | passive | Connect a single 402Ω ±1% resistor between XRES and ground. |
| 11 | VDD18 | power_in | 1.8V analog supply (1.7V to 1.9V recommended); place a 10nF decoupling capacitor as close as possible to the pin. |
| 12 | SION/SIO | bidirectional | Inverted twisted-pair serial-data input/output (SION) or coax serial-data input/output (SIO), selected by CFG1 state at power-up; use 0.1µF link isolation capacitor in GMSL2. |
| 13 | SIOP | bidirectional | Noninverted twisted-pair serial-data input/output, with configuration determined by CFG1 state at power-up. |
| 14 | CAP_VDD | passive | Decoupling capacitor pin for the 1.0V core supply; place a 10nF capacitor close to the pin with at least 10µF bulk nearby. |
| 15 | VDD | power_in | 1.0V core supply with optional on-chip LDO: connect 0.95V to 1.05V to bypass the LDO, or 1.14V to 1.26V to use the internal 1.0V regulator. |
| 16 | CFG1 | input | Configuration pin whose voltage is latched at power-up to select coax/twisted pair, GMSL mode and tunnel/pixel mode (see Table 9). |
| 17 | VDDIO | power_in | 1.8V to 3.3V I/O supply (1.7V to 3.6V recommended range). |
| 18 | MFP6 | bidirectional | Multifunction pin: LMN0 line fault monitor input or GPIO6 (power-up default GPI6 with 1MΩ pull-down to ground). |
| 19 | MFP7 | bidirectional | Multifunction pin: LMN1 line fault monitor input or GPIO7 (power-up default GPI7 with 1MΩ pull-down to ground). |
| 20 | VTERM | power_in | 1.2V D-PHY supply (1.14V to 1.26V recommended range). |
| 21 | D0P | output | CSI-2 data lane 0 noninverted output. |
| 22 | D0N | output | CSI-2 data lane 0 inverted output. |
| 23 | D1P | output | CSI-2 data lane 1 noninverted output. |
| 24 | D1N | output | CSI-2 data lane 1 inverted output. |
| 25 | D2P | output | CSI-2 data lane 2 noninverted output. |
| 26 | D2N | output | CSI-2 data lane 2 inverted output. |
| 27 | CKP | output | CSI-2 clock lane noninverted output. |
| 28 | CKN | output | CSI-2 clock lane inverted output. |
| 29 | D3P | output | CSI-2 data lane 3 noninverted output. |
| 30 | D3N | output | CSI-2 data lane 3 inverted output. |
| 31 | PWDNB | input | Active-low power-down input with 1MΩ pull-down to ground; set low to enter Power-down mode. |
| 32 | MFP8 | bidirectional | Multifunction pin, default ERRB open-drain error output with 40kΩ pull-up to VDDIO (low indicates an error), or GPIO8. |
| 33 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices Inc./Maxim Integrated |
| Package | TQFN-32(5x5) |
| Category | Interface |
| Pins | 33 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output Voltage Swing (Single-Ended) | VO | 190 | 250 | 310 | mV | GMSL2 reverse channel, RL = 100Ω ±1% | 7 |
| Output Voltage Swing (Differential) | VODT | 380 | 500 | 620 | mV | RL = 100Ω ±1%, peak-to-peak differential voltage | 7 |
| Change in VOD between Complementary Output States | ΔVOD | 25 | mV | RL = 100Ω ±1%, /VOD(H) − VOD(L)/ | 7 | ||
| Change in VOS between Complementary Output States | ΔVOS | 25 | mV | RL = 100Ω ±1%, /VOS(H) − VOS(L)/ | 7 | ||
| Termination Resistance (Internal), GMSL2 | RT | 50 | 55 | 60 | Ω | Any Pin to VDD18 | 7 |
| GMSL1 Differential High Output Peak Voltage | VRODH | 30 | 75 | mV | Forward channel disabled, HIM disabled | 7 | |
| GMSL1 Differential High Output Peak Voltage (HIM) | VRODH | 50 | 120 | mV | Forward channel disabled, HIM enabled | 7 | |
| GMSL1 Differential Low Output Peak Voltage | VRODL | -75 | -30 | mV | Forward channel disabled, HIM disabled | 7 | |
| GMSL1 Differential Low Output Peak Voltage (HIM) | VRODL | -120 | -50 | mV | Forward channel disabled, HIM enabled | 7 | |
| GMSL1 Single-Ended High-Output Peak Voltage | VROSH | 30 | 75 | mV | Forward channel disabled, HIM disabled | 7 | |
| GMSL1 Single-Ended High-Output Peak Voltage (HIM) | VROSH | 50 | 120 | mV | Forward channel disabled, HIM enabled | 7 | |
| GMSL1 Single-Ended Low-Output Peak Voltage | VROSL | -75 | -30 | mV | Forward channel disabled, HIM disabled | 7 | |
| GMSL1 Single-Ended Low-Output Peak Voltage (HIM) | VROSL | -120 | -50 | mV | Forward channel disabled, HIM enabled | 7 | |
| GMSL1 Termination Resistance (Internal) | RT | 50 | 55 | 60 | Ω | Any Pin to VDD18 | 7 |
| D-PHY LP High-Level Output Voltage | VOH | 0.95 | 1.2 | 1.3 | V | 7 | |
| D-PHY LP Low-Level Output Voltage | VOL | -50 | 50 | mV | 7 | ||
| HS Transmit Static Common Mode Voltage | VCMTX | 150 | 200 | 250 | mV | See Figure 3 | 7 |
| VCMTX Mismatch | /ΔVCMTX(1,0)/ | 5 | mV | See Figure 4 | 7 | ||
| HS Transmit Differential Voltage | /VOD/ | 140 | 200 | 270 | mV | See Figure 3 | 8 |
| VOD Mismatch | /ΔVOD/ | 14 | mV | See Figure 4 | 8 | ||
| HS Output High Voltage | VOHHS | 360 | mV | 8 | |||
| Single-Ended Output Impedance | ZOS | 40 | 50 | 62.5 | Ω | 8 | |
| Single-Ended Output Impedance Mismatch | ∆ZOS | 15 | % | 8 | |||
| I/O Low-Level Output Voltage | VOL | 0.4 | V | IOL = 4mA | 8 | ||
| I/O Input Current | IIN | 1 | μA | All pull-up/pull-down devices disabled. VIN = 0V to VDDIO | 8 | ||
| Open-Drain Low-Level Output Voltage | VOL | 0.4 | V | IOL = 4mA | 8 | ||
| PWDNB Input Current | IIN | 6 | μA | VIN = 0V to VDDIO | 8 | ||
| Push-Pull Low-Level Output Voltage | VOL | 0.4 | V | IOL = 4mA | 9 | ||
| Supply Current VDD (GMSL2, MAX96714R) | IDD | 78 | 220 | mA | 3Gbps link, 2.4Gbps video payload, PRBS24, four data lanes, 600Mbps per lane, VDD = 1.0V | 9 | |
| Supply Current VDD (GMSL2, MAX96714R) | IDD | 80 | 210 | mA | 3Gbps link, 2.4Gbps video payload, PRBS24, four data lanes, 600Mbps per lane, VDD = 1.2V | 9 | |
| Supply Current VDD18 (GMSL2, MAX96714R) | IDD | 114 | 155 | mA | 3Gbps link, 2.4Gbps video payload, PRBS24, four data lanes, 600Mbps per lane, VDD18 = 1.8V | 9 | |
| Supply Current VTERM (GMSL2, MAX96714R) | IDD | 14 | 22 | mA | 3Gbps link, 2.4Gbps video payload, PRBS24, four data lanes, 600Mbps per lane, VTERM = 1.2V | 9 | |
| Maximum VDDIO Supply Current | IDDIO | 44 | μA/MHz | Per toggling GPIO, CL = 20pF, VDDIO at 1.9V | 9 | ||
| Maximum VDDIO Supply Current | IDDIO | 81 | μA/MHz | Per toggling GPIO, CL = 20pF, VDDIO at 3.6V | 9 | ||
| Supply Current VDD (GMSL1) | IDD | 50 | 190 | mA | 3.12Gbps link, 2.5Gbps video payload, RGB888, four data lanes, High-Bandwidth Mode, VDD = 1.0V | 10 | |
| Supply Current VDD18 (GMSL1) | IDD | 60 | 82 | mA | 3.12Gbps link, 2.5Gbps video payload, RGB888, four data lanes, High-Bandwidth Mode, VDD18 = 1.8V | 10 | |
| Maximum Power-Down Current VDDIO | IDD | 6 | μA | VDDIO at 3.6V, TA = 25ºC | 10 | ||
| Maximum Power-Down Current VDD18 | IDD | 10 | μA | VDD18 at 1.9V, TA = 105ºC | 10 | ||
| Lock Time (MAX96714R) | tLOCK | 20 | ms | MAX96714R: From power-up, one-shot reset, or rising edge of PWDNB to rising edge of LOCK. (Note 5, Note 6) | 10 | ||
| PWDNB Hold Time (GMSL2) | tHOLD_PWDNB | 1 | ms | The minimum duration PWDNB must be held LOW to reset the chip. | 10 | ||
| GMSL Reverse Channel Transmitter Rise/Fall Time | tR, tF | 2300 | ps | 20% to 80%, VO = 250mV, RL = 100Ω | 10 | ||
| Total Serial Output p-p Jitter | tTSOJ | 0.15 | UI | PRBS7, single-ended or differential output. | 10 | ||
| Deterministic Serial Output p-p Jitter | tDSOJ | 0.1 | UI | PRBS7, single-ended or differential output. | 10 | ||
| GPI-GPO Delay Reverse Path, delay-compensated | tGPDR | 15 | μs | Delay-compensated mode. See Figure 16. | 11 | ||
| GPI-GPO Delay Reverse Path, non-compensated | tGPDR | 6 | μs | Non-delay-compensated mode. See Figure 16. | 11 | ||
| GPI-GPO Skew Reverse Path | tSKEW | 7 | ns | Delay-compensated mode, between GPI-GPO within a single link or link-to-link. See Figure 16. | 11 | ||
| GMSL1 Maximum Lock Time | tLOCK1 | 4 | ms | See Figure 6. | 11 | ||
| Data Lane Bit Rate | DLBR | 80 | 2500 | Mbps | 11 | ||
| Clock Lane Frequency | CLFREQ | 40 | 1250 | MHz | 11 | ||
| I2C Wake Time (MAX96714R) | tWAKEUP | 2.25 | ms | From power-up, or rising edge of PWDNB to local register access. | 13 | ||
| Output Fall Time (MAX96714R) | tF | 150 | ns | 70% to 30%, CL = 20pF to 100pF, 1kΩ pull-up to VDDIO | 13 | ||
| SCL Clock Frequency, high range | fSCL | 400 | 1000 | kHz | High fSCL range | 13 | |
| Crystal Frequency Stability + Tolerance | fTN | -200 | 200 | ppm | 15 | ||
| VTERM Supply Range | VTERM | 1.14 | 1.2 | 1.26 | V | 22 | |
| VDD18 Supply Range | VDD18 | 1.7 | 1.8 | 1.9 | V | 22 | |
| VDD Supply Range (1.0V nominal) | VDD | 0.95 | 1 | 1.05 | V | Nominal voltage 1.0V | 22 |
| VDD Supply Range (1.2V nominal) | VDD | 1.14 | 1.2 | 1.26 | V | Nominal voltage 1.2V | 22 |
| VDDIO Supply Range | VDDIO | 1.7 | 3.6 | V | 22 | ||
| Operating Junction Temperature | TJ | -40 | 125 | ºC | 22 | ||
| Operating Ambient Temperature | TA | -40 | 105 | °C | 7 | ||
| VDDIO Absolute Maximum | VDDIO | -0.3 | 3.9 | V | With respect to ground | 6 | |
| VDD18 Absolute Maximum | VDD18 | -0.3 | 2 | V | With respect to ground | 6 | |
| VDD Absolute Maximum | VDD | -0.3 | 2 | V | With respect to ground | 6 | |
| VTERM Absolute Maximum | VTERM | -0.3 | 1.32 | V | With respect to ground | 6 | |
| CAP_VDD Absolute Maximum | CAP_VDD | -0.3 | 1.2 | V | With respect to ground | 6 | |
| Storage Temperature Range | -40 | 150 | °C | 6 | |||
| Junction to Ambient Thermal Resistance | θJA | 29 | °C/W | 32-Pin TQFN, four-layer board | 6 | ||
| Junction to Case Thermal Resistance | θJC | 1.7 | °C/W | 32-Pin TQFN, four-layer board | 6 |
CAD (KiCad official)
- Symbol:
MAX96714RGTJ - Footprint:
Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.3x3.3mm - 3D model: TQFN-32(5x5) (KiCad packages3D, STEP)
- 3D model files:
max96714rgtj-etched.step/max96714rgtj-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max96714rgtj.step/max96714rgtj.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices Inc./Maxim Integrated datasheet (165 pp, sha256
51fc4d62cdc4e20f, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).