component
MAX823TEUK+T
Public Made by Adomby adom
Analog Devices Inc Maxim Integrated Supervisor And Reset ICs, SOT-23-5. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
MAX823TEUK+T
Analog Devices Inc Maxim Integrated · Supervisor And Reset ICs · SOT-23-5
MAX823TEUK+T from Analog Devices Inc Maxim Integrated, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RESET | output | Active-low reset output that stays low whenever VCC is below the reset threshold or MR is logic low, and for 200ms (tRP) after VCC rises above threshold, a watchdog reset, or MR returns high; it is guaranteed to be in the correct state for VCC down to 1V and both sources and sinks current (800µA max source for L/M, 400µA for T/S/R/Z/Y). |
| 2 | GND | power_in | Ground reference for the device. |
| 3 | MR | input | Manual reset input where a logic low asserts reset and reset stays asserted while MR is low and for 200ms after it returns high, with an internal 35-75kΩ (52kΩ typical) pullup so it may be left open or tied to VCC when unused. |
| 4 | WDI | input | Watchdog input that must toggle within the watchdog timeout period (1.12s min, 1.60s typ, 2.40s max) or reset is asserted, with the timer cleared by reset or any WDI edge; leaving WDI unconnected or three-stated disables the watchdog, and WDI input current is limited to 160µA maximum when driven high. |
| 5 | VCC | power_in | Supply voltage input, specified for +3.15V to +3.6V for the MAX823T suffix with absolute maximum rating of -0.3V to +6.0V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices Inc Maxim Integrated |
| Package | SOT-23-5 |
| Category | Power Management (PMIC) |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Reset threshold (MAX823T, TA = TMIN to TMAX) | VRST | 3 | 3.15 | V | MAX82_T, TA = TMIN to TMAX | 3 | |
| Reset timeout period | tRP | 140 | 200 | 280 | ms | 3 | |
| RESET output voltage high | VOH | 0.8 | ×VCC | MAX82_T/S/R/Z/Y, VCC = VRST max, ISOURCE = 30µA | 3 | ||
| RESET output voltage low | VOL | 0.3 | V | MAX82_T/S/R/Z/Y, VCC = VRST min, ISINK = 1.2mA | 3 | ||
| RESET output short-circuit current (pullup) | ISOURCE | 400 | µA | MAX82_T/S/R/Z/Y, RESET = 0V, VCC = 3.6V | 3 | ||
| Watchdog timeout period | tWD | 1.12 | 1.6 | 2.4 | s | 3 | |
| WDI pulse width | tWDI | 50 | ns | VIL = 0.4V, VIH = 0.8×VCC | 3 | ||
| WDI input voltage low | VIL | 0.3 | ×VCC | 3 | |||
| WDI input voltage high | VIH | 0.7 | ×VCC | 3 | |||
| WDI input current (WDI = VCC) | 120 | 160 | µA | WDI = VCC, time average | 3 | ||
| WDI input current (WDI = 0) | -20 | -15 | µA | WDI = 0, time average | 3 | ||
| MR input voltage low | VIL | 0.3 | ×VCC | MR input | 4 | ||
| MR input voltage high | VIH | 0.7 | ×VCC | MR input | 4 | ||
| MR pulse width | 1 | µs | 4 | ||||
| MR noise immunity (pulse width with no reset) | 100 | ns | pulse width with no reset | 4 | |||
| MR to reset delay | 500 | ns | 4 | ||||
| MR pullup resistance (internal) | 35 | 52 | 75 | kΩ | 4 | ||
| Supply current (SOT23 only) | ISUPPLY | 5 | 12 | µA | MAX823T/S/R/Z/Y, MR unconnected | 2 | |
| Operating voltage range | VCC | 1 | 5.5 | V | 2 | ||
| Reset threshold hysteresis | 5 | mV | MAX82_T/S/R/Z/Y | 3 | |||
| Reset threshold temperature coefficient | 40 | ppm/°C | 3 | ||||
| VCC to RESET delay | 20 | µs | VRST - VCC = 100mV | 3 | |||
| Recommended VCC range (MAX82_T) | VCC | 3.15 | 3.6 | V | MAX82_T | 2 | |
| Operating temperature range (EUK, SOT23) | TA | -40 | 125 | °C | MAX82_EUK, SOT23 | 2 | |
| VCC supply voltage (absolute maximum) | VCC | -0.3 | 6 | V | 2 | ||
| All other pins voltage (absolute maximum) | -0.3 | V | max = VCC + 0.3V | 2 | |||
| Input current, all pins except RESET and RESET | 20 | mA | 2 | ||||
| Output current, RESET, RESET | 20 | mA | 2 | ||||
| Storage temperature range | TSTG | -65 | 150 | °C | 2 | ||
| Lead temperature (soldering, 10 s) | 300 | °C | soldering, 10s | 2 |
CAD (KiCad official)
- Symbol:
MAX823TEUK+T - Footprint:
Package_TO_SOT_SMD:SOT-23-5 - 3D model: SOT-23-5 (KiCad packages3D, STEP)
- 3D model files:
max823teuk-t-etched.step/max823teuk-t-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max823teuk-t.step/max823teuk-t.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices Inc Maxim Integrated datasheet (10 pp, sha256
7479c571698c1831, retrieved 2026-10-18, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MAX823TEUK+T
**Analog Devices Inc Maxim Integrated** · Supervisor And Reset ICs · SOT-23-5
MAX823TEUK+T from Analog Devices Inc Maxim Integrated, in a SOT-23-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RESET | output | Active-low reset output that stays low whenever VCC is below the reset threshold or MR is logic low, and for 200ms (tRP) after VCC rises above threshold, a watchdog reset, or MR returns high; it is guaranteed to be in the correct state for VCC down to 1V and both sources and sinks current (800µA max source for L/M, 400µA for T/S/R/Z/Y). |
| 2 | GND | power_in | Ground reference for the device. |
| 3 | MR | input | Manual reset input where a logic low asserts reset and reset stays asserted while MR is low and for 200ms after it returns high, with an internal 35-75kΩ (52kΩ typical) pullup so it may be left open or tied to VCC when unused. |
| 4 | WDI | input | Watchdog input that must toggle within the watchdog timeout period (1.12s min, 1.60s typ, 2.40s max) or reset is asserted, with the timer cleared by reset or any WDI edge; leaving WDI unconnected or three-stated disables the watchdog, and WDI input current is limited to 160µA maximum when driven high. |
| 5 | VCC | power_in | Supply voltage input, specified for +3.15V to +3.6V for the MAX823T suffix with absolute maximum rating of -0.3V to +6.0V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices Inc Maxim Integrated |
| Package | SOT-23-5 |
| Category | Power Management (PMIC) |
| Pins | 5 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Reset threshold (MAX823T, TA = TMIN to TMAX) | VRST | 3 | | 3.15 | V | MAX82_T, TA = TMIN to TMAX | 3 |
| Reset timeout period | tRP | 140 | 200 | 280 | ms | | 3 |
| RESET output voltage high | VOH | 0.8 | | | ×VCC | MAX82_T/S/R/Z/Y, VCC = VRST max, ISOURCE = 30µA | 3 |
| RESET output voltage low | VOL | | | 0.3 | V | MAX82_T/S/R/Z/Y, VCC = VRST min, ISINK = 1.2mA | 3 |
| RESET output short-circuit current (pullup) | ISOURCE | | | 400 | µA | MAX82_T/S/R/Z/Y, RESET = 0V, VCC = 3.6V | 3 |
| Watchdog timeout period | tWD | 1.12 | 1.6 | 2.4 | s | | 3 |
| WDI pulse width | tWDI | 50 | | | ns | VIL = 0.4V, VIH = 0.8×VCC | 3 |
| WDI input voltage low | VIL | | | 0.3 | ×VCC | | 3 |
| WDI input voltage high | VIH | 0.7 | | | ×VCC | | 3 |
| WDI input current (WDI = VCC) | | 120 | | 160 | µA | WDI = VCC, time average | 3 |
| WDI input current (WDI = 0) | | -20 | | -15 | µA | WDI = 0, time average | 3 |
| MR input voltage low | VIL | | | 0.3 | ×VCC | MR input | 4 |
| MR input voltage high | VIH | 0.7 | | | ×VCC | MR input | 4 |
| MR pulse width | | 1 | | | µs | | 4 |
| MR noise immunity (pulse width with no reset) | | | | 100 | ns | pulse width with no reset | 4 |
| MR to reset delay | | | | 500 | ns | | 4 |
| MR pullup resistance (internal) | | 35 | 52 | 75 | kΩ | | 4 |
| Supply current (SOT23 only) | ISUPPLY | | 5 | 12 | µA | MAX823T/S/R/Z/Y, MR unconnected | 2 |
| Operating voltage range | VCC | 1 | | 5.5 | V | | 2 |
| Reset threshold hysteresis | | | 5 | | mV | MAX82_T/S/R/Z/Y | 3 |
| Reset threshold temperature coefficient | | | 40 | | ppm/°C | | 3 |
| VCC to RESET delay | | | 20 | | µs | VRST - VCC = 100mV | 3 |
| Recommended VCC range (MAX82_T) | VCC | 3.15 | | 3.6 | V | MAX82_T | 2 |
| Operating temperature range (EUK, SOT23) | TA | -40 | | 125 | °C | MAX82_EUK, SOT23 | 2 |
| VCC supply voltage (absolute maximum) | VCC | -0.3 | | 6 | V | | 2 |
| All other pins voltage (absolute maximum) | | -0.3 | | | V | max = VCC + 0.3V | 2 |
| Input current, all pins except RESET and RESET | | | | 20 | mA | | 2 |
| Output current, RESET, RESET | | | | 20 | mA | | 2 |
| Storage temperature range | TSTG | -65 | | 150 | °C | | 2 |
| Lead temperature (soldering, 10 s) | | | | 300 | °C | soldering, 10s | 2 |
## CAD (KiCad official)
- Symbol: `MAX823TEUK+T`
- Footprint: `Package_TO_SOT_SMD:SOT-23-5`
- 3D model: SOT-23-5 (KiCad packages3D, STEP)
- 3D model files: `max823teuk-t-etched.step` / `max823teuk-t-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `max823teuk-t.step` / `max823teuk-t.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices Inc Maxim Integrated datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8586175445125906432) (10 pp, sha256 `7479c571698c1831`, retrieved 2026-10-18, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/max823teuk-t-datasheet.pdf)