Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MAX6650EUB+T

Maxim Integrated · Motor Driver ICs · MSOP-10

MAX6650EUB+T from Maxim Integrated, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, read twice and the reads agreed). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 TACH0 input Tachometer input used to close the loop around the tachometer; withstands -0.3V to +13.2V.
2 GND power_in Ground.
3 SDA bidirectional 2-wire serial-data input/output (open drain).
4 SCL input 2-wire serial clock input.
5 ADD input Slave address select input, strapped to GND, VCC, open or via 10kΩ/100kΩ to GND to choose one of four addresses (Table 1).
6 GPIO1 bidirectional Open-drain general-purpose input/output, configurable as an output or as an input (FULL ON or general purpose), sinking 10mA.
7 GPIO0 bidirectional Open-drain general-purpose input/output, configurable as a general input/output line or an active-low ALERT output, sinking 10mA.
8 OUT output Output that drives the external MOSFET or bipolar transistor; sinks 10mA and sources 50mA.
9 VCC power_in +3.0V to +5.5V power supply.
10 FB input Feedback input that closes the loop around the external MOSFET or bipolar transistor; withstands -0.3V to +13.2V.

Key specifications

Parameter Value
Manufacturer Maxim Integrated
Package MSOP-10
Category Power Supply Chip
Pins 10

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply Voltage VCC 3 5.5 V 2
Supply Current ICC 10 mA Full-on mode, IOUT = 0 2
Output Voltage Range (min) VOUT 0.3 V IOUT = ±100μA 2
Output Sink Current ISINK 10 mA VOUT = 0.5V 2
Output Source Current ISOURCE 50 mA VOUT = VCC - 1.8V 2
Tachometer Input Impedance RTACH_ 70 100 150 kΩ 0 < VTACH < 9V 2
DAC Differential Nonlinearity 5 LSB Guaranteed monotonicity on FB (Note 1) 2
Useful DAC Resolution 8 bits Measured at FB (Note 1) 2
Feedback Input Impedance RFB 70 100 150 kΩ 0 < VFB < 9V 2
GPIO Input Low Voltage VIL(GPIO_) 0.8 V 2
GPIO Input High Voltage VIH(GPIO_) 2 V VCC ≤ 3.6V 2
GPIO Input High Voltage VIH(GPIO_) 3 V VCC > 3.6V 2
GPIO Input Hysteresis VHYS 200 mV 2
GPIO Pullup Resistor RGPIO_ 100 kΩ 2
GPIO Output Sink Current IGPIO_ 10 mA VGPIO_ = 0.4V 2
Clock Frequency fCLK 254 kHz 3
Clock Frequency Uncertainty fCLK -10 10 % VCC = 5V 3
SCL Clock Frequency fSCL 0 400 kHz 3
Bus Free Time Between Stop and Start tBUF 1.3 μs 3
Hold-Time Start Condition tHD:STA 0.6 μs 3
Low Period of SCL Clock tLOW 1.3 μs 3
High Period of SCL Clock tHIGH 0.6 μs 3
Data Hold Time tHD:DAT 0 900 μs Note 5 3
Data Setup Time tSU:DAT 100 ns 3
Rise-Time SDA/SCL Signal (Receiving) tR 300 ns Note 6 3
Fall-Time SDA/SCL Signal (Receiving) tF 300 ns Note 6 3
Fall-Time SDA Signal (Transmitting) tF 250 ns ISINK < 6mA (Note 6) 3
ADD Input Low Voltage VIL(ADD) 0.1 V Selects slave address 90h (Table 1) 3
ADD Input Leakage ILADD -1 0 μA Selects slave address 36h (Table 1) (Note 3) 3
ADD External Pulldown Resistor to GND RADD 9.5 10.5 kΩ Selects slave address 3Eh (Table 1) 3
ADD Pulldown Current IADD -80 -40 μA VADD = 0.5V (Note 4) 3
Data Output Sink Current ISDA 6 mA VSDA = 0.6V 3
Input Leakage Current -1 1 μA 0 < VIN < VCC 3
SDA/SCL Input Low Voltage VIL 0.8 V 3
SDA/SCL Input High Voltage VIH 2 V VCC ≤ 3.6V 3
SDA/SCL Input High Voltage VIH 3 V VCC > 3.6V 3
SDA/SCL Input Hysteresis VHYS 200 mV 3
Setup Time for Stop Condition tSU:STO 0.6 μs 4
Pulse Width of Spike Suppressed tSPIKE 0 50 ns 4
VCC to GND VCC -0.3 6 V 2
FB, TACH_ Voltage -0.3 13.2 V 2
Maximum Current Into VCC, GND, VOUT 100 mA 2
Maximum Current Into All Other Pins 50 mA 2
Operating Temperature Range -40 85 °C 2
Junction Temperature 150 °C 2
Storage Temperature Range -65 150 °C 2
Lead Temperature 300 °C soldering, 10s 2
Soldering Temperature (reflow), Lead(Pb)-free 260 °C 2
μMAX Power Dissipation Derating 5.6 mW/°C above +70°C 2

CAD (KiCad official)

  • Symbol: MAX6650EUB+T
  • Footprint: Package_SO:MSOP-10_3x3mm_P0.5mm
  • 3D model: MSOP-10 (KiCad packages3D, STEP)
  • 3D model files: max6650eub-t-etched.step / max6650eub-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); max6650eub-t.step / max6650eub-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Maxim Integrated datasheet (25 pp, sha256 cee9d3417b77f26f, retrieved 2026-11-20)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF