main
Ray
Publish 0.1.0
3971e24
MAX485EESA-HXY
HXY MOSFET · RS-485/RS-422 ICs · SOP-8
MAX485EESA-HXY from HXY MOSFET, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RO | output | Receiver output: high when VA exceeds VB by 200mV and low when VA is below VB by 200mV; high-impedance when RE is high. |
| 2 | RE | input | Receiver output enable, active low; when RE is high the receiver output is high-impedance. |
| 3 | DE | input | Driver output enable, active high; when DE is low the driver output is high-impedance, and DE high puts the device in transmit mode. |
| 4 | DI | input | Driver input: DI low drives A high and B low, and DI high gives the opposite output states. |
| 5 | GND | power_in | Ground, negative power supply terminal; all voltages are referenced to ground. |
| 6 | A | bidirectional | Receiver non-inverting input and driver non-inverting output. |
| 7 | B | bidirectional | Receiver inverting input and driver inverting output. |
| 8 | VCC | power_in | Positive power supply terminal; the device operates from a single 5V supply. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HXY MOSFET |
| Package | SOP-8 |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 10 | V | 2 | |||
| Control input voltage (RE, DE) | RE、 DE | -0.5 | 10 | V | 2 | ||
| Driver input voltage | DI | -0.5 | 10 | V | 2 | ||
| Driver output voltage (A, B) | A、B | -0.5 | 15 | V | 2 | ||
| Receiver input voltage (A, B) | A、B | -0.5 | 15 | V | 2 | ||
| Receiver output voltage | RO | -0.5 | 10 | V | 2 | ||
| Storage temperature | Tstg | -65 | 160 | ℃ | 2 | ||
| Operating temperature | TA | -40 | 85 | ℃ | 2 | ||
| Input high voltage | VIH | 2 | V | DE,RE | 2 | ||
| Input high voltage | VIH | 2.8 | V | DI | 2 | ||
| Input low voltage | VIL | 0.8 | V | DE,RE | 2 | ||
| Input low voltage | VIL | 1.6 | V | DI | 2 | ||
| Input current (DE, RE, DI) | IIN1 | -2 | 2 | uA | DE,RE,DI | 2 | |
| Input current (A, B) | IIN2 | 60 | 150 | uA | DE=0V, VCC=5V, VIN=5V | 2 | |
| Input current (A, B) | IIN2 | 180 | 400 | uA | DE=0V, VCC=5V, VIN=0V | 2 | |
| Receiver differential threshold voltage | VTH | -0.2 | 0.2 | V | - | 2 | |
| Receiver output high voltage | VOH | 3.5 | 4.5 | V | IO=-4mA, VID=200mV | 2 | |
| Receiver output low voltage | VOL | 0.2 | 0.4 | V | IO=4mA, VID=-200mV | 2 | |
| Receiver tri-state output current | IOZR | -1 | 1 | uA | 0.4V≤VO≤2.4V | 2 | |
| Supply current, no load (DE=VCC) | ICC | 1.2 | 1.6 | mV | RE、DI=0 or VCC, DE=VCC | 2 | |
| Supply current, no load (DE=0) | ICC | 1.1 | 1.5 | mV | RE、DI=0 or VCC, DE=0 | 2 | |
| Driver short-circuit current (VO=High) | IOSD1 | 120 | 250 | mA | DE=RE=5V, DI=0, VA=5V | 2 | |
| Driver short-circuit current (VO=Low) | IOSD2 | 120 | 250 | mA | DE=RE=5V, DI=0, VB=0 | 2 | |
| Receiver short-circuit current | IOSR | 60 | 100 | mA | 0V≤VO≤VCC | 2 | |
| ESD protection (A and B pins, human body model) | ESD | -4 | 4 | KV | Human body model, pins A and B | 2 | |
| Driver input to output propagation delay (rising) | tPLH | 40 | 70 | 90 | ns | See Fig 2; RDIFF=50Ω, CL1=CL2=100pF | 3 |
| Driver input to output propagation delay (falling) | tPLL | 10 | 40 | 60 | ns | See Fig 2; RDIFF=50Ω, CL1=CL2=100pF | 3 |
| Driver rise time | tR | 40 | 60 | ns | 3 | ||
| Driver fall time | tF | 40 | 60 | ns | 3 | ||
| Receiver input to output propagation delay (rising) | tPLH | 20 | 60 | 200 | ns | See Fig 2 and Fig 4; RDIFF=50Ω, CL1=CL2=100pF | 3 |
| Receiver input to output propagation delay (falling) | tPHL | 20 | 40 | 200 | ns | See Fig 2 and Fig 4; RDIFF=50Ω, CL1=CL2=100pF | 3 |
| Receiver enable to output low | tZL | 50 | 80 | ns | 见图1,图5,CL=15pF,S2 关闭 | 3 | |
| Receiver enable to output high | tZH | 60 | 90 | ns | 见图1,图5,CL=15pF,S1 关闭 | 3 | |
| Receiver output low to disable | tLZ | 50 | 80 | ns | 见图1,图5,CL=15pF,S2 关闭 | 3 | |
| Receiver output high to disable | tHZ | 60 | 90 | ns | 见图1,图5,CL=15pF,S1 关闭 | 3 | |
| Receiver hysteresis | △VTH | 70 | mV | - | 2 | ||
| Receiver input impedance | RIN | 48 | KΩ | - | 2 | ||
| Driver output skew to output | SKEW | 30 | ns | 3 | |||
| Differential receiver skew /tPLH-tPHL/ | SKD | 20 | ns | Differential receiver | 3 | ||
| Maximum data rate | MAX | 2.5 | Mbps | 3 |
CAD (KiCad official)
- Symbol:
MAX485EESA-HXY - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
max485eesa-hxy-etched.step/max485eesa-hxy-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max485eesa-hxy.step/max485eesa-hxy.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: HXY MOSFET datasheet (8 pp, sha256
b99dbe8ac0d1d4cc, retrieved 2026-11-05, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MAX485EESA-HXY
**HXY MOSFET** · RS-485/RS-422 ICs · SOP-8
MAX485EESA-HXY from HXY MOSFET, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | RO | output | Receiver output: high when VA exceeds VB by 200mV and low when VA is below VB by 200mV; high-impedance when RE is high. |
| 2 | RE | input | Receiver output enable, active low; when RE is high the receiver output is high-impedance. |
| 3 | DE | input | Driver output enable, active high; when DE is low the driver output is high-impedance, and DE high puts the device in transmit mode. |
| 4 | DI | input | Driver input: DI low drives A high and B low, and DI high gives the opposite output states. |
| 5 | GND | power_in | Ground, negative power supply terminal; all voltages are referenced to ground. |
| 6 | A | bidirectional | Receiver non-inverting input and driver non-inverting output. |
| 7 | B | bidirectional | Receiver inverting input and driver inverting output. |
| 8 | VCC | power_in | Positive power supply terminal; the device operates from a single 5V supply. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | HXY MOSFET |
| Package | SOP-8 |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 8 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | | | 10 | V | | 2 |
| Control input voltage (RE, DE) | RE、 DE | -0.5 | | 10 | V | | 2 |
| Driver input voltage | DI | -0.5 | | 10 | V | | 2 |
| Driver output voltage (A, B) | A、B | -0.5 | | 15 | V | | 2 |
| Receiver input voltage (A, B) | A、B | -0.5 | | 15 | V | | 2 |
| Receiver output voltage | RO | -0.5 | | 10 | V | | 2 |
| Storage temperature | Tstg | -65 | | 160 | ℃ | | 2 |
| Operating temperature | TA | -40 | | 85 | ℃ | | 2 |
| Input high voltage | VIH | 2 | | | V | DE,RE | 2 |
| Input high voltage | VIH | 2.8 | | | V | DI | 2 |
| Input low voltage | VIL | | | 0.8 | V | DE,RE | 2 |
| Input low voltage | VIL | | | 1.6 | V | DI | 2 |
| Input current (DE, RE, DI) | IIN1 | -2 | | 2 | uA | DE,RE,DI | 2 |
| Input current (A, B) | IIN2 | | 60 | 150 | uA | DE=0V, VCC=5V, VIN=5V | 2 |
| Input current (A, B) | IIN2 | | 180 | 400 | uA | DE=0V, VCC=5V, VIN=0V | 2 |
| Receiver differential threshold voltage | VTH | -0.2 | | 0.2 | V | - | 2 |
| Receiver output high voltage | VOH | 3.5 | 4.5 | | V | IO=-4mA, VID=200mV | 2 |
| Receiver output low voltage | VOL | | 0.2 | 0.4 | V | IO=4mA, VID=-200mV | 2 |
| Receiver tri-state output current | IOZR | -1 | | 1 | uA | 0.4V≤VO≤2.4V | 2 |
| Supply current, no load (DE=VCC) | ICC | | 1.2 | 1.6 | mV | RE、DI=0 or VCC, DE=VCC | 2 |
| Supply current, no load (DE=0) | ICC | | 1.1 | 1.5 | mV | RE、DI=0 or VCC, DE=0 | 2 |
| Driver short-circuit current (VO=High) | IOSD1 | | 120 | 250 | mA | DE=RE=5V, DI=0, VA=5V | 2 |
| Driver short-circuit current (VO=Low) | IOSD2 | | 120 | 250 | mA | DE=RE=5V, DI=0, VB=0 | 2 |
| Receiver short-circuit current | IOSR | | 60 | 100 | mA | 0V≤VO≤VCC | 2 |
| ESD protection (A and B pins, human body model) | ESD | -4 | | 4 | KV | Human body model, pins A and B | 2 |
| Driver input to output propagation delay (rising) | tPLH | 40 | 70 | 90 | ns | See Fig 2; RDIFF=50Ω, CL1=CL2=100pF | 3 |
| Driver input to output propagation delay (falling) | tPLL | 10 | 40 | 60 | ns | See Fig 2; RDIFF=50Ω, CL1=CL2=100pF | 3 |
| Driver rise time | tR | | 40 | 60 | ns | | 3 |
| Driver fall time | tF | | 40 | 60 | ns | | 3 |
| Receiver input to output propagation delay (rising) | tPLH | 20 | 60 | 200 | ns | See Fig 2 and Fig 4; RDIFF=50Ω, CL1=CL2=100pF | 3 |
| Receiver input to output propagation delay (falling) | tPHL | 20 | 40 | 200 | ns | See Fig 2 and Fig 4; RDIFF=50Ω, CL1=CL2=100pF | 3 |
| Receiver enable to output low | tZL | | 50 | 80 | ns | 见图1,图5,CL=15pF,S2 关闭 | 3 |
| Receiver enable to output high | tZH | | 60 | 90 | ns | 见图1,图5,CL=15pF,S1 关闭 | 3 |
| Receiver output low to disable | tLZ | | 50 | 80 | ns | 见图1,图5,CL=15pF,S2 关闭 | 3 |
| Receiver output high to disable | tHZ | | 60 | 90 | ns | 见图1,图5,CL=15pF,S1 关闭 | 3 |
| Receiver hysteresis | △VTH | | 70 | | mV | - | 2 |
| Receiver input impedance | RIN | | 48 | | KΩ | - | 2 |
| Driver output skew to output | SKEW | | 30 | | ns | | 3 |
| Differential receiver skew /tPLH-tPHL/ | SKD | | 20 | | ns | Differential receiver | 3 |
| Maximum data rate | MAX | | 2.5 | | Mbps | | 3 |
## CAD (KiCad official)
- Symbol: `MAX485EESA-HXY`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files: `max485eesa-hxy-etched.step` / `max485eesa-hxy-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `max485eesa-hxy.step` / `max485eesa-hxy.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [HXY MOSFET datasheet](docs/max485eesa-hxy-datasheet.pdf) (8 pp, sha256 `b99dbe8ac0d1d4cc`, retrieved 2026-11-05, tier: lcsc)
- **Datasheet language:** Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/max485eesa-hxy-datasheet.pdf)