← Commit history
README.md+67−65@@ -8,34 +8,34 @@ MAX3238EIDBR from Texas Instruments, in a SSOP-28-208mil. Pinout and pin descrip | Pin | Name | Type | Function | |---|---|---|---|-| 1 | C2+ | passive | Positive terminal of charge-pump capacitor C2 connected between C2+ and C2−. |-| 2 | GND | power_in | Ground reference for all device voltages. |-| 3 | C2− | passive | Negative terminal of charge-pump capacitor C2 connected between C2+ and C2−. |-| 4 | V− | power_out | Charge-pump generated negative supply (about −5.5 V) with absolute maximum of −7 V, decoupled by capacitor C4. |-| 5 | DOUT1 | output | RS-232 driver 1 output with ±15 kV HBM ESD protection and output voltage range of ±13.2 V maximum. |-| 6 | DOUT2 | output | RS-232 driver 2 output with ±15 kV HBM ESD protection and output voltage range of ±13.2 V maximum. |-| 7 | DOUT3 | output | RS-232 driver 3 output with ±15 kV HBM ESD protection and output voltage range of ±13.2 V maximum. |-| 8 | RIN1 | input | RS-232 receiver 1 input with ±15 kV HBM ESD protection, ±25 V input range and 5 kΩ typical input resistance. |-| 9 | RIN2 | input | RS-232 receiver 2 input with ±15 kV HBM ESD protection, ±25 V input range and 5 kΩ typical input resistance. |-| 10 | DOUT4 | output | RS-232 driver 4 output with ±15 kV HBM ESD protection and output voltage range of ±13.2 V maximum. |-| 11 | RIN3 | input | RS-232 receiver 3 input with ±15 kV HBM ESD protection, ±25 V input range and 5 kΩ typical input resistance. |-| 12 | DOUT5 | output | RS-232 driver 5 output with ±15 kV HBM ESD protection and output voltage range of ±13.2 V maximum. |-| 13 | FORCEON | input | Logic input that, when high with FORCEOFF high, disables auto-powerdown plus; when low with FORCEOFF high, auto-powerdown plus is enabled (high-level input 2 V min at 3.3 V, 2.4 V min at 5 V). |-| 14 | FORCEOFF | input | Logic input that powers off drivers and charge pump when low (driver outputs high-impedance, ROUT2/ROUT3 high-impedance) while ROUT1B stays active; maximum input voltage 6 V. |-| 15 | INVALID | output | Valid-signal output that is high if any receiver input is above 2.7 V or below −2.7 V, and low when all receiver inputs stay between −0.3 V and 0.3 V for more than 30 µs. |-| 16 | ROUT1B | output | Always-active noninverting output of receiver 1 that remains active while the device is powered down, allowing ring-indicator use. |-| 17 | DIN5 | input | Driver 5 logic input (2 V min high at 3.3 V, 2.4 V min at 5 V, 0.8 V max low, accepts up to 5.5 V). |-| 18 | ROUT3 | output | Receiver 3 logic output, high-impedance when FORCEOFF is low; VOH at least VCC − 0.6 V at −1 mA. |-| 19 | DIN4 | input | Driver 4 logic input (2 V min high at 3.3 V, 2.4 V min at 5 V, 0.8 V max low, accepts up to 5.5 V). |-| 20 | ROUT2 | output | Receiver 2 logic output, high-impedance when FORCEOFF is low; VOH at least VCC − 0.6 V at −1 mA. |-| 21 | ROUT1 | output | Receiver 1 logic output, high-impedance when FORCEOFF is low; VOH at least VCC − 0.6 V at −1 mA. |-| 22 | DIN3 | input | Driver 3 logic input (2 V min high at 3.3 V, 2.4 V min at 5 V, 0.8 V max low, accepts up to 5.5 V). |-| 23 | DIN2 | input | Driver 2 logic input (2 V min high at 3.3 V, 2.4 V min at 5 V, 0.8 V max low, accepts up to 5.5 V). |-| 24 | DIN1 | input | Driver 1 logic input (2 V min high at 3.3 V, 2.4 V min at 5 V, 0.8 V max low, accepts up to 5.5 V). |-| 25 | C1− | passive | Negative terminal of charge-pump capacitor C1 connected between C1+ and C1−. |-| 26 | VCC | power_in | Supply voltage input of 3 V to 3.6 V or 4.5 V to 5.5 V recommended (−0.3 V to 6 V absolute maximum), bypassed with 0.1 µF. |-| 27 | V+ | power_out | Charge-pump generated positive supply (about +5.5 V) with absolute maximum of 7 V, decoupled by capacitor C3. |-| 28 | C1+ | passive | Positive terminal of charge-pump capacitor C1 connected between C1+ and C1−. |+| 1 | C2+ | passive | Positive terminal of charge-pump capacitor C2, connected between C2+ and C2−. |+| 2 | GND | power_in | Ground; all supply voltages are specified with respect to this network GND. |+| 3 | C2− | passive | Negative terminal of charge-pump capacitor C2, connected between C2+ and C2−. |+| 4 | V− | power_out | Charge-pump negative supply output (about −5.5 V), abs max −0.3 V to −7 V, decoupled with capacitor C4. |+| 5 | DOUT1 | output | RS-232 driver 1 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off. |+| 6 | DOUT2 | output | RS-232 driver 2 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off. |+| 7 | DOUT3 | output | RS-232 driver 3 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off. |+| 8 | RIN1 | input | RS-232 receiver 1 input with ±15 kV HBM ESD protection, input range ±25 V, 5 kΩ typical input resistance. |+| 9 | RIN2 | input | RS-232 receiver 2 input with ±15 kV HBM ESD protection, input range ±25 V, 5 kΩ typical input resistance. |+| 10 | DOUT4 | output | RS-232 driver 4 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off. |+| 11 | RIN3 | input | RS-232 receiver 3 input with ±15 kV HBM ESD protection, input range ±25 V, 5 kΩ typical input resistance. |+| 12 | DOUT5 | output | RS-232 driver 5 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off. |+| 13 | FORCEON | input | Control input; with FORCEOFF high, FORCEON high disables auto-powerdown plus and FORCEON low enables it, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply). |+| 14 | FORCEOFF | input | Control input; low powers off the drivers and charge pump (supply current 1 µA typical), high allows operation, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply). |+| 15 | INVALID | output | Valid-data flag, high if any receiver input is above 2.7 V or below −2.7 V, low if all receiver inputs stay between −0.3 V and 0.3 V for more than 30 µs. |+| 16 | ROUT1B | output | Always-active noninverting receiver 1 output that remains active while the device is powered down, VOH min VCC − 0.6 V at −1 mA, VOL max 0.4 V at 1.6 mA. |+| 17 | DIN5 | input | Driver 5 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum. |+| 18 | ROUT3 | output | Receiver 3 logic output, high-impedance when FORCEOFF is low, VOH min VCC − 0.6 V at −1 mA, VOL max 0.4 V at 1.6 mA. |+| 19 | DIN4 | input | Driver 4 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum. |+| 20 | ROUT2 | output | Receiver 2 logic output, high-impedance when FORCEOFF is low, VOH min VCC − 0.6 V at −1 mA, VOL max 0.4 V at 1.6 mA. |+| 21 | ROUT1 | output | Receiver 1 logic output, high-impedance when FORCEOFF is low, VOH min VCC − 0.6 V at −1 mA, VOL max 0.4 V at 1.6 mA. |+| 22 | DIN3 | input | Driver 3 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum. |+| 23 | DIN2 | input | Driver 2 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum. |+| 24 | DIN1 | input | Driver 1 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum. |+| 25 | C1− | passive | Negative terminal of charge-pump capacitor C1, connected between C1+ and C1−. |+| 26 | VCC | power_in | Supply voltage input, 3 V to 5.5 V (abs max 6 V), bypassed with 0.1 µF to GND. |+| 27 | V+ | power_out | Charge-pump positive supply output (about 5.5 V), abs max −0.3 V to 7 V, decoupled with capacitor C3 (C3 can be connected to VCC or GND). |+| 28 | C1+ | passive | Positive terminal of charge-pump capacitor C1, connected between C1+ and C1−. | ## Key specifications @@ -54,51 +54,53 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries |---|---|---|---|---|---|---|---| | Supply voltage, VCC = 3.3 V | VCC | 3 | 3.3 | 3.6 | V | VCC = 3.3 V | 5 | | Supply voltage, VCC = 5 V | VCC | 4.5 | 5 | 5.5 | V | VCC = 5 V | 5 |-| Driver and control high-level input voltage (DIN, FORCEOFF) | VIH | 2 | | 5.5 | V | DIN, FORCEOFF, VCC = 3.3 V | 5 |-| Driver and control high-level input voltage (FORCEON) | VIH | 2.4 | | 5.5 | V | FORCEON, VCC = 5 V | 5 |+| Driver and control high-level input voltage (DIN, FORCEOFF) | VIH | 2 | | 5.5 | V | VCC = 3.3 V | 5 |+| Driver and control high-level input voltage (FORCEON) | VIH | 2.4 | | 5.5 | V | VCC = 5 V | 5 | | Driver and control low-level input voltage | VIL | 0 | | 0.8 | V | DIN, FORCEOFF, FORCEON | 5 | | Receiver input voltage | VI | -25 | | 25 | V | | 5 |-| Operating free-air temperature, MAX3238EI | TA | -40 | | 85 | °C | MAX3238EI | 5 |-| VCC supply voltage range | VCC | -0.3 | | 6 | V | | 5 |-| V+ positive-output supply voltage range | V+ | -0.3 | | 7 | V | | 5 |-| V- negative-output supply voltage range | V- | -7 | | 0.3 | V | | 5 |-| V+, V- supply voltage difference | V+, V- | | | 13 | V | | 5 |-| Driver input voltage range (FORCEOFF, FORCEON) | VI | -0.3 | | 6 | V | Driver (FORCEOFF, FORCEON) | 5 |+| Operating free-air temperature (MAX3238EI) | TA | -40 | | 85 | °C | MAX3238EI | 5 |+| Supply voltage range VCC | VCC | -0.3 | | 6 | V | | 5 |+| Positive-output supply voltage range | V+ | -0.3 | | 7 | V | | 5 |+| Negative-output supply voltage range | V- | 0.3 | | -7 | V | | 5 |+| Supply voltage difference | V+, V- | | | 13 | V | | 5 |+| Driver input voltage range (FORCEOFF, FORCEON) | VI | -0.3 | | 6 | V | Driver | 5 | | Receiver input voltage range | VI | -25 | | 25 | V | Receiver | 5 | | Driver output voltage range | VO | -13.2 | | 13.2 | V | Driver | 5 |-| Receiver output voltage range (INVALID) | VO | -0.3 | | | V | Receiver (INVALID); printed maximum is VCC + 0.3 V | 5 |-| Package thermal impedance, DB package | θJA | | 62 | | °C/W | DB package | 5 |+| Receiver output voltage range (INVALID) | VO | -0.3 | | | V | | 5 | | Operating virtual junction temperature | TJ | | | 150 | °C | | 5 | | Storage temperature range | Tstg | -65 | | 150 | °C | | 5 |-| High-level output voltage (driver) | VOH | 5 | 5.4 | | V | All DOUT at RL = 3 kΩ to GND | 6 |-| Low-level output voltage (driver) | VOL | | -5.4 | -5 | V | All DOUT at RL = 3 kΩ to GND | 6 |-| High-level input current | IIH | -1 | 0.01 | 1 | µA | VI = VCC | 6 |-| Low-level input current | IIL | -1 | 0.01 | 1 | µA | VI at GND | 6 |-| Short-circuit output current, VCC = 3.6 V | IOS | -60 | 35 | 60 | mA | VCC = 3.6 V, VO = 0 V | 6 |-| Short-circuit output current, VCC = 5.5 V | IOS | -100 | 40 | 100 | mA | VCC = 5.5 V, VO = 0 V | 6 |-| Output resistance | ro | 300 | | | Ω | VCC, V+, and V- = 0 V, VO = ±2 V; printed maximum is 10M Ω | 6 |-| Output leakage current, VCC = 3 V to 3.6 V | IOZ | -25 | | 25 | µA | FORCEOFF = GND, VO = ±12 V, VCC = 3 V to 3.6 V | 6 |-| Output leakage current, VCC = 4.5 V to 5.5 V | IOZ | -25 | | 25 | µA | FORCEOFF = GND, VO = ±10 V, VCC = 4.5 V to 5.5 V | 6 |-| Maximum data rate | | 250 | | 400 | kbit/s | CL = 1000 pF, RL = 3 kΩ, One DOUT switching, See Figure 1 | 6 |-| Driver pulse skew | tsk(p) | | | 100 | ns | CL = 150 pF to 2500 pF, RL = 3 kΩ to 7 kΩ, See Figure 2 | 6 |-| Slew rate, transition region (CL = 150 pF to 1000 pF) | SR(tr) | 6 | | 30 | V/µs | CL = 150 pF to 1000 pF | 6 |-| Slew rate, transition region (VCC = 3.3 V) | SR(tr) | 4 | | 30 | V/µs | VCC = 3.3 V, RL = 3 kΩ to 7 kΩ, CL = 150 pF to 2500 pF, see Figure 1 | 6 |-| Low-level output voltage (receiver) | VOL | | | 0.4 | V | IOL = 1.6 mA | 7 |-| Positive-going input threshold voltage, VCC = 3.3 V | VIT+ | 1.5 | | 2.4 | V | VCC = 3.3 V | 7 |-| Positive-going input threshold voltage, VCC = 5 V | VIT+ | 1.8 | | 2.4 | V | VCC = 5 V | 7 |-| Negative-going input threshold voltage, VCC = 3.3 V | VIT- | 0.6 | | 1.2 | V | VCC = 3.3 V | 7 |-| Negative-going input threshold voltage, VCC = 5 V | VIT- | 0.8 | | 1.5 | V | VCC = 5 V | 7 |-| Output leakage current (except ROUT1B) | IOZ | -10 | 0.05 | 10 | µA | FORCEOFF = 0 V | 7 |-| Input resistance | ri | 3 | 5 | 7 | kΩ | VI = ±3 V to ±25 V | 7 |-| Receiver input threshold for INVALID high-level output (positive) | VT+(valid) | 2.7 | | | V | FORCEON = GND, FORCEOFF = VCC | 8 |-| Receiver input threshold for INVALID high-level output (negative) | VT-(valid) | | | -2.7 | V | FORCEON = GND, FORCEOFF = VCC | 8 |-| Receiver input threshold for INVALID low-level output | VT(invalid) | -0.3 | | 0.3 | V | FORCEON = GND, FORCEOFF = VCC | 8 |-| INVALID low-level output voltage | VOL | | | 0.4 | V | IOL = 1.6 mA, FORCEON = GND, FORCEOFF = VCC | 8 |-| Receiver or driver edge to auto-powerdown plus | tdis | 15 | 30 | 60 | s | | 8 |+| Input leakage current (FORCEOFF, FORCEON) | II | | 0.01 | 1 | µA | | 5 | | Supply current, auto-powerdown plus disabled | ICC | | 0.5 | 2 | mA | No load, FORCEOFF and FORCEON at VCC | 5 | | Supply current, powered off | ICC | | 1 | 10 | µA | No load, FORCEOFF at GND | 5 | | Supply current, auto-powerdown plus enabled | ICC | | 1 | 10 | µA | No load, FORCEOFF at VCC, FORCEON at GND, All RIN are open or grounded | 5 |-| Input leakage current (FORCEOFF, FORCEON) | | -1 | 0.01 | 1 | µA | | 5 |+| Driver high-level output voltage | VOH | 5 | 5.4 | | V | All DOUT at RL = 3 kΩ to GND | 6 |+| Driver low-level output voltage | VOL | -5 | -5.4 | | V | All DOUT at RL = 3 kΩ to GND | 6 |+| High-level input current | IIH | | 0.01 | 1 | µA | VI = VCC | 6 |+| Low-level input current | IIL | | 0.01 | 1 | µA | VI at GND | 6 |+| Short-circuit output current | IOS | | 35 | 60 | mA | VCC = 3.6 V, VO = 0 V | 6 |+| Short-circuit output current | IOS | | 40 | 100 | mA | VCC = 5.5 V, VO = 0 V | 6 |+| Output resistance | ro | 300 | | | Ω | VCC, V+, and V- = 0 V, VO = ±2 V | 6 |+| Output leakage current | IOZ | | | 25 | µA | FORCEOFF = GND; VO = ±12 V, VCC = 3 V to 3.6 V | 6 |+| Maximum data rate | | 250 | 400 | | kbit/s | CL = 1000 pF, RL = 3 kΩ, One DOUT switching, See Figure 1 | 6 |+| Pulse skew | tsk(p) | | | 100 | ns | CL = 150 pF to 2500 pF, RL = 3 kΩ to 7 kΩ, See Figure 2 | 6 |+| Slew rate, transition region | SR(tr) | 6 | | 30 | V/µs | VCC = 3.3 V, CL = 150 pF to 1000 pF, RL = 3 kΩ to 7 kΩ, See Figure 1 | 6 |+| Slew rate, transition region | SR(tr) | 4 | | 30 | V/µs | VCC = 3.3 V, CL = 150 pF to 2500 pF, RL = 3 kΩ to 7 kΩ, See Figure 1 | 6 |+| Receiver high-level output voltage (INVALID), see review | VOL | | | 0.4 | V | IOL = 1.6 mA | 7 |+| Receiver positive-going input threshold voltage | VIT+ | 1.5 | | 2.4 | V | VCC = 3.3 V | 7 |+| Receiver positive-going input threshold voltage | VIT+ | 1.8 | | 2.4 | V | VCC = 5 V | 7 |+| Receiver negative-going input threshold voltage | VIT- | 0.6 | | 1.2 | V | VCC = 3.3 V | 7 |+| Receiver negative-going input threshold voltage | VIT- | 0.8 | | 1.5 | V | VCC = 5 V | 7 |+| Output leakage current (except ROUT1B) | IOZ | | 0.05 | 10 | µA | FORCEOFF = 0 V | 7 |+| Input resistance | ri | 3 | 5 | 7 | kΩ | VI = ±3 V to ±25 V | 7 |+| Receiver input threshold for INVALID high-level output voltage (valid, positive) | VT+(valid) | 2.7 | | | V | FORCEON = GND, FORCEOFF = VCC | 8 |+| Receiver input threshold for INVALID high-level output voltage (valid, negative) | VT-(valid) | | | -2.7 | V | FORCEON = GND, FORCEOFF = VCC | 8 |+| Receiver input threshold for INVALID low-level output voltage | VT(invalid) | -0.3 | | 0.3 | V | FORCEON = GND, FORCEOFF = VCC | 8 |+| INVALID low-level output voltage | VOL | | | 0.4 | V | IOL = 1.6 mA, FORCEON = GND, FORCEOFF = VCC | 8 |+| Propagation delay time, low- to high-level output (INVALID) | tvalid | | | 0.1 | µs | | 8 |+| Propagation delay time, high- to low-level output (INVALID) | tinvalid | | | 50 | µs | | 8 |+| Supply enable time | ten | | | 25 | µs | | 8 |+| Receiver or driver edge to auto-powerdown plus | tdis | 15 | 30 | 60 | s | | 8 |+| Package thermal impedance, DB package | θJA | | 62 | | °C/W | DB package | 5 | ## CAD (KiCad official) @@ -111,7 +113,7 @@ Limits as printed in the datasheet (page.json `metadata.characteristics` carries Data extracted from the manufacturer datasheet, not a distributor listing: -- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/max3238e.pdf) (23 pp, sha256 `1d519ae7a9e53f86`, retrieved 2026-11-13, tier: manufacturer)+- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/max3238e.pdf) (23 pp, sha256 `1d519ae7a9e53f86`, retrieved 2026-11-17) - **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - **CAD:** KiCad official libraries (CC-BY-SA 4.0).
package.json+40−39@@ -1,6 +1,6 @@ { "slug": "max3238eidbr",- "version": "0.1.2",+ "version": "0.1.3", "type": "component", "description": "Texas Instruments Pre-ordered Chips, SSOP-28-208mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.", "tags": [@@ -53,7 +53,7 @@ "mouser": "595-MAX3238EIDBR" }, "distributor_check": {- "checked_at": "2026-11-13T01:26:46Z",+ "checked_at": "2026-11-17T22:10:38Z", "source": "Component Ocean /api/assign-pns", "digikey": { "pn": "296-19817-2-ND",@@ -69,169 +69,169 @@ "number": "1", "name": "C2+", "type": "passive",- "description": "Positive terminal of charge-pump capacitor C2 connected between C2+ and C2−."+ "description": "Positive terminal of charge-pump capacitor C2, connected between C2+ and C2−." }, { "number": "2", "name": "GND", "type": "power_in",- "description": "Ground reference for all device voltages."+ "description": "Ground; all supply voltages are specified with respect to this network GND." }, { "number": "3", "name": "C2−", "type": "passive",- "description": "Negative terminal of charge-pump capacitor C2 connected between C2+ and C2−."+ "description": "Negative terminal of charge-pump capacitor C2, connected between C2+ and C2−." }, { "number": "4", "name": "V−", "type": "power_out",- "description": "Charge-pump generated negative supply (about −5.5 V) with absolute maximum of −7 V, decoupled by capacitor C4."+ "description": "Charge-pump negative supply output (about −5.5 V), abs max −0.3 V to −7 V, decoupled with capacitor C4." }, { "number": "5", "name": "DOUT1", "type": "output",- "description": "RS-232 driver 1 output with ±15 kV HBM ESD protection and output voltage range of ±13.2 V maximum."+ "description": "RS-232 driver 1 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off." }, { "number": "6", "name": "DOUT2", "type": "output",- "description": "RS-232 driver 2 output with ±15 kV HBM ESD protection and output voltage range of ±13.2 V maximum."+ "description": "RS-232 driver 2 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off." }, { "number": "7", "name": "DOUT3", "type": "output",- "description": "RS-232 driver 3 output with ±15 kV HBM ESD protection and output voltage range of ±13.2 V maximum."+ "description": "RS-232 driver 3 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off." }, { "number": "8", "name": "RIN1", "type": "input",- "description": "RS-232 receiver 1 input with ±15 kV HBM ESD protection, ±25 V input range and 5 kΩ typical input resistance."+ "description": "RS-232 receiver 1 input with ±15 kV HBM ESD protection, input range ±25 V, 5 kΩ typical input resistance." }, { "number": "9", "name": "RIN2", "type": "input",- "description": "RS-232 receiver 2 input with ±15 kV HBM ESD protection, ±25 V input range and 5 kΩ typical input resistance."+ "description": "RS-232 receiver 2 input with ±15 kV HBM ESD protection, input range ±25 V, 5 kΩ typical input resistance." }, { "number": "10", "name": "DOUT4", "type": "output",- "description": "RS-232 driver 4 output with ±15 kV HBM ESD protection and output voltage range of ±13.2 V maximum."+ "description": "RS-232 driver 4 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off." }, { "number": "11", "name": "RIN3", "type": "input",- "description": "RS-232 receiver 3 input with ±15 kV HBM ESD protection, ±25 V input range and 5 kΩ typical input resistance."+ "description": "RS-232 receiver 3 input with ±15 kV HBM ESD protection, input range ±25 V, 5 kΩ typical input resistance." }, { "number": "12", "name": "DOUT5", "type": "output",- "description": "RS-232 driver 5 output with ±15 kV HBM ESD protection and output voltage range of ±13.2 V maximum."+ "description": "RS-232 driver 5 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off." }, { "number": "13", "name": "FORCEON", "type": "input",- "description": "Logic input that, when high with FORCEOFF high, disables auto-powerdown plus; when low with FORCEOFF high, auto-powerdown plus is enabled (high-level input 2 V min at 3.3 V, 2.4 V min at 5 V)."+ "description": "Control input; with FORCEOFF high, FORCEON high disables auto-powerdown plus and FORCEON low enables it, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply)." }, { "number": "14", "name": "FORCEOFF", "type": "input",- "description": "Logic input that powers off drivers and charge pump when low (driver outputs high-impedance, ROUT2/ROUT3 high-impedance) while ROUT1B stays active; maximum input voltage 6 V."+ "description": "Control input; low powers off the drivers and charge pump (supply current 1 µA typical), high allows operation, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply)." }, { "number": "15", "name": "INVALID", "type": "output",- "description": "Valid-signal output that is high if any receiver input is above 2.7 V or below −2.7 V, and low when all receiver inputs stay between −0.3 V and 0.3 V for more than 30 µs."+ "description": "Valid-data flag, high if any receiver input is above 2.7 V or below −2.7 V, low if all receiver inputs stay between −0.3 V and 0.3 V for more than 30 µs." }, { "number": "16", "name": "ROUT1B", "type": "output",- "description": "Always-active noninverting output of receiver 1 that remains active while the device is powered down, allowing ring-indicator use."+ "description": "Always-active noninverting receiver 1 output that remains active while the device is powered down, VOH min VCC − 0.6 V at −1 mA, VOL max 0.4 V at 1.6 mA." }, { "number": "17", "name": "DIN5", "type": "input",- "description": "Driver 5 logic input (2 V min high at 3.3 V, 2.4 V min at 5 V, 0.8 V max low, accepts up to 5.5 V)."+ "description": "Driver 5 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum." }, { "number": "18", "name": "ROUT3", "type": "output",- "description": "Receiver 3 logic output, high-impedance when FORCEOFF is low; VOH at least VCC − 0.6 V at −1 mA."+ "description": "Receiver 3 logic output, high-impedance when FORCEOFF is low, VOH min VCC − 0.6 V at −1 mA, VOL max 0.4 V at 1.6 mA." }, { "number": "19", "name": "DIN4", "type": "input",- "description": "Driver 4 logic input (2 V min high at 3.3 V, 2.4 V min at 5 V, 0.8 V max low, accepts up to 5.5 V)."+ "description": "Driver 4 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum." }, { "number": "20", "name": "ROUT2", "type": "output",- "description": "Receiver 2 logic output, high-impedance when FORCEOFF is low; VOH at least VCC − 0.6 V at −1 mA."+ "description": "Receiver 2 logic output, high-impedance when FORCEOFF is low, VOH min VCC − 0.6 V at −1 mA, VOL max 0.4 V at 1.6 mA." }, { "number": "21", "name": "ROUT1", "type": "output",- "description": "Receiver 1 logic output, high-impedance when FORCEOFF is low; VOH at least VCC − 0.6 V at −1 mA."+ "description": "Receiver 1 logic output, high-impedance when FORCEOFF is low, VOH min VCC − 0.6 V at −1 mA, VOL max 0.4 V at 1.6 mA." }, { "number": "22", "name": "DIN3", "type": "input",- "description": "Driver 3 logic input (2 V min high at 3.3 V, 2.4 V min at 5 V, 0.8 V max low, accepts up to 5.5 V)."+ "description": "Driver 3 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum." }, { "number": "23", "name": "DIN2", "type": "input",- "description": "Driver 2 logic input (2 V min high at 3.3 V, 2.4 V min at 5 V, 0.8 V max low, accepts up to 5.5 V)."+ "description": "Driver 2 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum." }, { "number": "24", "name": "DIN1", "type": "input",- "description": "Driver 1 logic input (2 V min high at 3.3 V, 2.4 V min at 5 V, 0.8 V max low, accepts up to 5.5 V)."+ "description": "Driver 1 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum." }, { "number": "25", "name": "C1−", "type": "passive",- "description": "Negative terminal of charge-pump capacitor C1 connected between C1+ and C1−."+ "description": "Negative terminal of charge-pump capacitor C1, connected between C1+ and C1−." }, { "number": "26", "name": "VCC", "type": "power_in",- "description": "Supply voltage input of 3 V to 3.6 V or 4.5 V to 5.5 V recommended (−0.3 V to 6 V absolute maximum), bypassed with 0.1 µF."+ "description": "Supply voltage input, 3 V to 5.5 V (abs max 6 V), bypassed with 0.1 µF to GND." }, { "number": "27", "name": "V+", "type": "power_out",- "description": "Charge-pump generated positive supply (about +5.5 V) with absolute maximum of 7 V, decoupled by capacitor C3."+ "description": "Charge-pump positive supply output (about 5.5 V), abs max −0.3 V to 7 V, decoupled with capacitor C3 (C3 can be connected to VCC or GND)." }, { "number": "28", "name": "C1+", "type": "passive",- "description": "Positive terminal of charge-pump capacitor C1 connected between C1+ and C1−."+ "description": "Positive terminal of charge-pump capacitor C1, connected between C1+ and C1−." } ], "provenance": {@@ -245,18 +245,19 @@ "consensus": "agreed", "guards": "pin_guards 0.1: passed", "guard_notes": [- "extractor flagged: The pin-number-to-name mapping for the DB (SSOP-28) package was inferred from the ordered name list ; Charge-pump capacitor and V+/V− pin roles are inferred from the names; the datasheet's typical circu",- "3/28 pins cited to the wrong page (name found elsewhere): ['8:RIN1@p7', '9:RIN2@p7', '11:RIN3@p7']"+ "extractor flagged: Pin numbers were assigned from the top-view (DB, DW, PW) name sequence on page 1, because the extrac; The DB-package pin list in the top view gives pins 1-4 and 25-28 as power and charge-pump pins. Pin ; The absolute-maximum entry for the V− supply range is printed as '0.3 –7 V' in the extracted text. T",+ "8/28 pins cited to the wrong page (name found elsewhere): ['8:RIN1@p7', '9:RIN2@p7', '11:RIN3@p7', '13:FORCEON@p8']" ], "pages_sent": 23,- "cost_usd": 0.1172,- "at": "2026-11-13T01:26:31"+ "cost_usd": 0.1158,+ "at": "2026-11-17T22:10:05" }, "datasheet": { "url": "https://www.ti.com/lit/ds/symlink/max3238e.pdf", "pages": 23, "sha256": "1d519ae7a9e53f86",- "source_tier": "mfr"+ "source_tier": "mfr",+ "citation": "Texas Instruments datasheet" }, "cad": "KiCad official (CC-BY-SA 4.0)", "pins": {@@ -287,7 +288,7 @@ "centre_offset_mm": 0.0, "footprint_binding": "identity", "sha256": "7aa76979ae41da44bded1ed74115012868f2f3f5a757faf32bb9df4f92c1e313",- "checked": "2026-11-13",+ "checked": "2026-11-17", "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)" }, {@@ -305,13 +306,13 @@ "zmin_mm": 0.0, "centre_offset_mm": 0.0, "footprint_binding": "identity",- "sha256": "635f12d6ab4b5ebe77fa43f46ea4175ec1744c004b994f904b304772b7f7c41d",- "checked": "2026-11-13",+ "sha256": "d96ff6576a9d7b80272c091a1544fa458839edf233d6210b5a273aeb8595ada2",+ "checked": "2026-11-17", "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)" } ], "package_dims": {- "package_code": "DB0028A",+ "package_code": "DB (SSOP-28, DB0028A)", "source_page": 20, "D": { "nom_mm": 10.2,
page.json+43−40@@ -4,7 +4,7 @@ "slug": "max3238eidbr", "title": "MAX3238EIDBR", "brief": "Texas Instruments Pre-ordered Chips, SSOP-28-208mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",- "version": "0.1.2",+ "version": "0.1.3", "license": "CC-BY-SA-4.0", "tags": [ "component",@@ -36,7 +36,7 @@ "mouser": "595-MAX3238EIDBR" }, "distributor_check": {- "checked_at": "2026-11-13T01:26:46Z",+ "checked_at": "2026-11-17T22:10:38Z", "source": "Component Ocean /api/assign-pns", "digikey": { "pn": "296-19817-2-ND",@@ -52,169 +52,169 @@ "number": "1", "name": "C2+", "type": "passive",- "description": "Positive terminal of charge-pump capacitor C2 connected between C2+ and C2−."+ "description": "Positive terminal of charge-pump capacitor C2, connected between C2+ and C2−." }, { "number": "2", "name": "GND", "type": "power_in",- "description": "Ground reference for all device voltages."+ "description": "Ground; all supply voltages are specified with respect to this network GND." }, { "number": "3", "name": "C2−", "type": "passive",- "description": "Negative terminal of charge-pump capacitor C2 connected between C2+ and C2−."+ "description": "Negative terminal of charge-pump capacitor C2, connected between C2+ and C2−." }, { "number": "4", "name": "V−", "type": "power_out",- "description": "Charge-pump generated negative supply (about −5.5 V) with absolute maximum of −7 V, decoupled by capacitor C4."+ "description": "Charge-pump negative supply output (about −5.5 V), abs max −0.3 V to −7 V, decoupled with capacitor C4." }, { "number": "5", "name": "DOUT1", "type": "output",- "description": "RS-232 driver 1 output with ±15 kV HBM ESD protection and output voltage range of ±13.2 V maximum."+ "description": "RS-232 driver 1 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off." }, { "number": "6", "name": "DOUT2", "type": "output",- "description": "RS-232 driver 2 output with ±15 kV HBM ESD protection and output voltage range of ±13.2 V maximum."+ "description": "RS-232 driver 2 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off." }, { "number": "7", "name": "DOUT3", "type": "output",- "description": "RS-232 driver 3 output with ±15 kV HBM ESD protection and output voltage range of ±13.2 V maximum."+ "description": "RS-232 driver 3 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off." }, { "number": "8", "name": "RIN1", "type": "input",- "description": "RS-232 receiver 1 input with ±15 kV HBM ESD protection, ±25 V input range and 5 kΩ typical input resistance."+ "description": "RS-232 receiver 1 input with ±15 kV HBM ESD protection, input range ±25 V, 5 kΩ typical input resistance." }, { "number": "9", "name": "RIN2", "type": "input",- "description": "RS-232 receiver 2 input with ±15 kV HBM ESD protection, ±25 V input range and 5 kΩ typical input resistance."+ "description": "RS-232 receiver 2 input with ±15 kV HBM ESD protection, input range ±25 V, 5 kΩ typical input resistance." }, { "number": "10", "name": "DOUT4", "type": "output",- "description": "RS-232 driver 4 output with ±15 kV HBM ESD protection and output voltage range of ±13.2 V maximum."+ "description": "RS-232 driver 4 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off." }, { "number": "11", "name": "RIN3", "type": "input",- "description": "RS-232 receiver 3 input with ±15 kV HBM ESD protection, ±25 V input range and 5 kΩ typical input resistance."+ "description": "RS-232 receiver 3 input with ±15 kV HBM ESD protection, input range ±25 V, 5 kΩ typical input resistance." }, { "number": "12", "name": "DOUT5", "type": "output",- "description": "RS-232 driver 5 output with ±15 kV HBM ESD protection and output voltage range of ±13.2 V maximum."+ "description": "RS-232 driver 5 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off." }, { "number": "13", "name": "FORCEON", "type": "input",- "description": "Logic input that, when high with FORCEOFF high, disables auto-powerdown plus; when low with FORCEOFF high, auto-powerdown plus is enabled (high-level input 2 V min at 3.3 V, 2.4 V min at 5 V)."+ "description": "Control input; with FORCEOFF high, FORCEON high disables auto-powerdown plus and FORCEON low enables it, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply)." }, { "number": "14", "name": "FORCEOFF", "type": "input",- "description": "Logic input that powers off drivers and charge pump when low (driver outputs high-impedance, ROUT2/ROUT3 high-impedance) while ROUT1B stays active; maximum input voltage 6 V."+ "description": "Control input; low powers off the drivers and charge pump (supply current 1 µA typical), high allows operation, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply)." }, { "number": "15", "name": "INVALID", "type": "output",- "description": "Valid-signal output that is high if any receiver input is above 2.7 V or below −2.7 V, and low when all receiver inputs stay between −0.3 V and 0.3 V for more than 30 µs."+ "description": "Valid-data flag, high if any receiver input is above 2.7 V or below −2.7 V, low if all receiver inputs stay between −0.3 V and 0.3 V for more than 30 µs." }, { "number": "16", "name": "ROUT1B", "type": "output",- "description": "Always-active noninverting output of receiver 1 that remains active while the device is powered down, allowing ring-indicator use."+ "description": "Always-active noninverting receiver 1 output that remains active while the device is powered down, VOH min VCC − 0.6 V at −1 mA, VOL max 0.4 V at 1.6 mA." }, { "number": "17", "name": "DIN5", "type": "input",- "description": "Driver 5 logic input (2 V min high at 3.3 V, 2.4 V min at 5 V, 0.8 V max low, accepts up to 5.5 V)."+ "description": "Driver 5 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum." }, { "number": "18", "name": "ROUT3", "type": "output",- "description": "Receiver 3 logic output, high-impedance when FORCEOFF is low; VOH at least VCC − 0.6 V at −1 mA."+ "description": "Receiver 3 logic output, high-impedance when FORCEOFF is low, VOH min VCC − 0.6 V at −1 mA, VOL max 0.4 V at 1.6 mA." }, { "number": "19", "name": "DIN4", "type": "input",- "description": "Driver 4 logic input (2 V min high at 3.3 V, 2.4 V min at 5 V, 0.8 V max low, accepts up to 5.5 V)."+ "description": "Driver 4 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum." }, { "number": "20", "name": "ROUT2", "type": "output",- "description": "Receiver 2 logic output, high-impedance when FORCEOFF is low; VOH at least VCC − 0.6 V at −1 mA."+ "description": "Receiver 2 logic output, high-impedance when FORCEOFF is low, VOH min VCC − 0.6 V at −1 mA, VOL max 0.4 V at 1.6 mA." }, { "number": "21", "name": "ROUT1", "type": "output",- "description": "Receiver 1 logic output, high-impedance when FORCEOFF is low; VOH at least VCC − 0.6 V at −1 mA."+ "description": "Receiver 1 logic output, high-impedance when FORCEOFF is low, VOH min VCC − 0.6 V at −1 mA, VOL max 0.4 V at 1.6 mA." }, { "number": "22", "name": "DIN3", "type": "input",- "description": "Driver 3 logic input (2 V min high at 3.3 V, 2.4 V min at 5 V, 0.8 V max low, accepts up to 5.5 V)."+ "description": "Driver 3 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum." }, { "number": "23", "name": "DIN2", "type": "input",- "description": "Driver 2 logic input (2 V min high at 3.3 V, 2.4 V min at 5 V, 0.8 V max low, accepts up to 5.5 V)."+ "description": "Driver 2 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum." }, { "number": "24", "name": "DIN1", "type": "input",- "description": "Driver 1 logic input (2 V min high at 3.3 V, 2.4 V min at 5 V, 0.8 V max low, accepts up to 5.5 V)."+ "description": "Driver 1 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum." }, { "number": "25", "name": "C1−", "type": "passive",- "description": "Negative terminal of charge-pump capacitor C1 connected between C1+ and C1−."+ "description": "Negative terminal of charge-pump capacitor C1, connected between C1+ and C1−." }, { "number": "26", "name": "VCC", "type": "power_in",- "description": "Supply voltage input of 3 V to 3.6 V or 4.5 V to 5.5 V recommended (−0.3 V to 6 V absolute maximum), bypassed with 0.1 µF."+ "description": "Supply voltage input, 3 V to 5.5 V (abs max 6 V), bypassed with 0.1 µF to GND." }, { "number": "27", "name": "V+", "type": "power_out",- "description": "Charge-pump generated positive supply (about +5.5 V) with absolute maximum of 7 V, decoupled by capacitor C3."+ "description": "Charge-pump positive supply output (about 5.5 V), abs max −0.3 V to 7 V, decoupled with capacitor C3 (C3 can be connected to VCC or GND)." }, { "number": "28", "name": "C1+", "type": "passive",- "description": "Positive terminal of charge-pump capacitor C1 connected between C1+ and C1−."+ "description": "Positive terminal of charge-pump capacitor C1, connected between C1+ and C1−." } ], "provenance": {@@ -228,18 +228,19 @@ "consensus": "agreed", "guards": "pin_guards 0.1: passed", "guard_notes": [- "extractor flagged: The pin-number-to-name mapping for the DB (SSOP-28) package was inferred from the ordered name list ; Charge-pump capacitor and V+/V− pin roles are inferred from the names; the datasheet's typical circu",- "3/28 pins cited to the wrong page (name found elsewhere): ['8:RIN1@p7', '9:RIN2@p7', '11:RIN3@p7']"+ "extractor flagged: Pin numbers were assigned from the top-view (DB, DW, PW) name sequence on page 1, because the extrac; The DB-package pin list in the top view gives pins 1-4 and 25-28 as power and charge-pump pins. Pin ; The absolute-maximum entry for the V− supply range is printed as '0.3 –7 V' in the extracted text. T",+ "8/28 pins cited to the wrong page (name found elsewhere): ['8:RIN1@p7', '9:RIN2@p7', '11:RIN3@p7', '13:FORCEON@p8']" ], "pages_sent": 23,- "cost_usd": 0.1172,- "at": "2026-11-13T01:26:31"+ "cost_usd": 0.1158,+ "at": "2026-11-17T22:10:05" }, "datasheet": { "url": "https://www.ti.com/lit/ds/symlink/max3238e.pdf", "pages": 23, "sha256": "1d519ae7a9e53f86",- "source_tier": "mfr"+ "source_tier": "mfr",+ "citation": "Texas Instruments datasheet" }, "cad": "KiCad official (CC-BY-SA 4.0)", "pins": {@@ -270,7 +271,7 @@ "centre_offset_mm": 0, "footprint_binding": "identity", "sha256": "7aa76979ae41da44bded1ed74115012868f2f3f5a757faf32bb9df4f92c1e313",- "checked": "2026-11-13",+ "checked": "2026-11-17", "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)" }, {@@ -288,13 +289,13 @@ "zmin_mm": 0, "centre_offset_mm": 0, "footprint_binding": "identity",- "sha256": "635f12d6ab4b5ebe77fa43f46ea4175ec1744c004b994f904b304772b7f7c41d",- "checked": "2026-11-13",+ "sha256": "d96ff6576a9d7b80272c091a1544fa458839edf233d6210b5a273aeb8595ada2",+ "checked": "2026-11-17", "checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)" } ], "package_dims": {- "package_code": "DB0028A",+ "package_code": "DB (SSOP-28, DB0028A)", "source_page": 20, "D": { "nom_mm": 10.2,@@ -959,5 +960,7 @@ ], "visibility": { "public": true- }+ },+ "description": "Texas Instruments Pre-ordered Chips, SSOP-28-208mil. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+ "org": "adom" }