Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

MAX3238EIDBR

Texas Instruments · Pre-ordered Chips · SSOP-28-208mil

MAX3238EIDBR from Texas Instruments, in a SSOP-28-208mil. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 C2+ passive Positive terminal of charge-pump capacitor C2, connected between C2+ and C2−.
2 GND power_in Ground; all supply voltages are specified with respect to this network GND.
3 C2− passive Negative terminal of charge-pump capacitor C2, connected between C2+ and C2−.
4 V− power_out Charge-pump negative supply output (about −5.5 V), abs max −0.3 V to −7 V, decoupled with capacitor C4.
5 DOUT1 output RS-232 driver 1 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off.
6 DOUT2 output RS-232 driver 2 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off.
7 DOUT3 output RS-232 driver 3 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off.
8 RIN1 input RS-232 receiver 1 input with ±15 kV HBM ESD protection, input range ±25 V, 5 kΩ typical input resistance.
9 RIN2 input RS-232 receiver 2 input with ±15 kV HBM ESD protection, input range ±25 V, 5 kΩ typical input resistance.
10 DOUT4 output RS-232 driver 4 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off.
11 RIN3 input RS-232 receiver 3 input with ±15 kV HBM ESD protection, input range ±25 V, 5 kΩ typical input resistance.
12 DOUT5 output RS-232 driver 5 output with ±15 kV HBM ESD protection, output range ±13.2 V, high-impedance when powered off.
13 FORCEON input Control input; with FORCEOFF high, FORCEON high disables auto-powerdown plus and FORCEON low enables it, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply).
14 FORCEOFF input Control input; low powers off the drivers and charge pump (supply current 1 µA typical), high allows operation, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply).
15 INVALID output Valid-data flag, high if any receiver input is above 2.7 V or below −2.7 V, low if all receiver inputs stay between −0.3 V and 0.3 V for more than 30 µs.
16 ROUT1B output Always-active noninverting receiver 1 output that remains active while the device is powered down, VOH min VCC − 0.6 V at −1 mA, VOL max 0.4 V at 1.6 mA.
17 DIN5 input Driver 5 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum.
18 ROUT3 output Receiver 3 logic output, high-impedance when FORCEOFF is low, VOH min VCC − 0.6 V at −1 mA, VOL max 0.4 V at 1.6 mA.
19 DIN4 input Driver 4 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum.
20 ROUT2 output Receiver 2 logic output, high-impedance when FORCEOFF is low, VOH min VCC − 0.6 V at −1 mA, VOL max 0.4 V at 1.6 mA.
21 ROUT1 output Receiver 1 logic output, high-impedance when FORCEOFF is low, VOH min VCC − 0.6 V at −1 mA, VOL max 0.4 V at 1.6 mA.
22 DIN3 input Driver 3 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum.
23 DIN2 input Driver 2 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum.
24 DIN1 input Driver 1 logic input, VIL max 0.8 V, VIH min 2 V (3.3 V supply) or 2.4 V (5 V supply), accepts 5.5 V maximum.
25 C1− passive Negative terminal of charge-pump capacitor C1, connected between C1+ and C1−.
26 VCC power_in Supply voltage input, 3 V to 5.5 V (abs max 6 V), bypassed with 0.1 µF to GND.
27 V+ power_out Charge-pump positive supply output (about 5.5 V), abs max −0.3 V to 7 V, decoupled with capacitor C3 (C3 can be connected to VCC or GND).
28 C1+ passive Positive terminal of charge-pump capacitor C1, connected between C1+ and C1−.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SSOP-28-208mil
Category Interface ICs
Pins 28

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Supply voltage, VCC = 3.3 V VCC 3 3.3 3.6 V VCC = 3.3 V 5
Supply voltage, VCC = 5 V VCC 4.5 5 5.5 V VCC = 5 V 5
Driver and control high-level input voltage (DIN, FORCEOFF) VIH 2 5.5 V VCC = 3.3 V 5
Driver and control high-level input voltage (FORCEON) VIH 2.4 5.5 V VCC = 5 V 5
Driver and control low-level input voltage VIL 0 0.8 V DIN, FORCEOFF, FORCEON 5
Receiver input voltage VI -25 25 V 5
Operating free-air temperature (MAX3238EI) TA -40 85 °C MAX3238EI 5
Supply voltage range VCC VCC -0.3 6 V 5
Positive-output supply voltage range V+ -0.3 7 V 5
Negative-output supply voltage range V- 0.3 -7 V 5
Supply voltage difference V+, V- 13 V 5
Driver input voltage range (FORCEOFF, FORCEON) VI -0.3 6 V Driver 5
Receiver input voltage range VI -25 25 V Receiver 5
Driver output voltage range VO -13.2 13.2 V Driver 5
Receiver output voltage range (INVALID) VO -0.3 V 5
Operating virtual junction temperature TJ 150 °C 5
Storage temperature range Tstg -65 150 °C 5
Input leakage current (FORCEOFF, FORCEON) II 0.01 1 µA 5
Supply current, auto-powerdown plus disabled ICC 0.5 2 mA No load, FORCEOFF and FORCEON at VCC 5
Supply current, powered off ICC 1 10 µA No load, FORCEOFF at GND 5
Supply current, auto-powerdown plus enabled ICC 1 10 µA No load, FORCEOFF at VCC, FORCEON at GND, All RIN are open or grounded 5
Driver high-level output voltage VOH 5 5.4 V All DOUT at RL = 3 kΩ to GND 6
Driver low-level output voltage VOL -5 -5.4 V All DOUT at RL = 3 kΩ to GND 6
High-level input current IIH 0.01 1 µA VI = VCC 6
Low-level input current IIL 0.01 1 µA VI at GND 6
Short-circuit output current IOS 35 60 mA VCC = 3.6 V, VO = 0 V 6
Short-circuit output current IOS 40 100 mA VCC = 5.5 V, VO = 0 V 6
Output resistance ro 300 Ω VCC, V+, and V- = 0 V, VO = ±2 V 6
Output leakage current IOZ 25 µA FORCEOFF = GND; VO = ±12 V, VCC = 3 V to 3.6 V 6
Maximum data rate 250 400 kbit/s CL = 1000 pF, RL = 3 kΩ, One DOUT switching, See Figure 1 6
Pulse skew tsk(p) 100 ns CL = 150 pF to 2500 pF, RL = 3 kΩ to 7 kΩ, See Figure 2 6
Slew rate, transition region SR(tr) 6 30 V/µs VCC = 3.3 V, CL = 150 pF to 1000 pF, RL = 3 kΩ to 7 kΩ, See Figure 1 6
Slew rate, transition region SR(tr) 4 30 V/µs VCC = 3.3 V, CL = 150 pF to 2500 pF, RL = 3 kΩ to 7 kΩ, See Figure 1 6
Receiver high-level output voltage (INVALID), see review VOL 0.4 V IOL = 1.6 mA 7
Receiver positive-going input threshold voltage VIT+ 1.5 2.4 V VCC = 3.3 V 7
Receiver positive-going input threshold voltage VIT+ 1.8 2.4 V VCC = 5 V 7
Receiver negative-going input threshold voltage VIT- 0.6 1.2 V VCC = 3.3 V 7
Receiver negative-going input threshold voltage VIT- 0.8 1.5 V VCC = 5 V 7
Output leakage current (except ROUT1B) IOZ 0.05 10 µA FORCEOFF = 0 V 7
Input resistance ri 3 5 7 kΩ VI = ±3 V to ±25 V 7
Receiver input threshold for INVALID high-level output voltage (valid, positive) VT+(valid) 2.7 V FORCEON = GND, FORCEOFF = VCC 8
Receiver input threshold for INVALID high-level output voltage (valid, negative) VT-(valid) -2.7 V FORCEON = GND, FORCEOFF = VCC 8
Receiver input threshold for INVALID low-level output voltage VT(invalid) -0.3 0.3 V FORCEON = GND, FORCEOFF = VCC 8
INVALID low-level output voltage VOL 0.4 V IOL = 1.6 mA, FORCEON = GND, FORCEOFF = VCC 8
Propagation delay time, low- to high-level output (INVALID) tvalid 0.1 µs 8
Propagation delay time, high- to low-level output (INVALID) tinvalid 50 µs 8
Supply enable time ten 25 µs 8
Receiver or driver edge to auto-powerdown plus tdis 15 30 60 s 8
Package thermal impedance, DB package θJA 62 °C/W DB package 5

CAD (KiCad official)

  • Symbol: MAX3238EIDBR
  • Footprint: Package_SO:SSOP-28_5.3x10.2mm_P0.65mm
  • 3D model: SSOP-28-208mil (KiCad packages3D, STEP)
  • 3D model files: max3238eidbr-etched.step / max3238eidbr-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); max3238eidbr.step / max3238eidbr.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (23 pp, sha256 1d519ae7a9e53f86, retrieved 2026-11-17)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF