main
Ray
Publish 0.1.0
dc57de1
MAX3226EEUE+
Analog Devices Inc./Maxim Integrated · RS232 ICs · TSSOP-16
MAX3226EEUE+ from Analog Devices Inc./Maxim Integrated, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | READY | output | Active-high ready-to-transmit output that goes high when V- falls below -4V and the device is ready to transmit. |
| 2 | C1+ | passive | Positive terminal of the voltage-doubler charge-pump capacitor. |
| 3 | V+ | power_out | +5.5V supply generated by the charge pump. |
| 4 | C1- | passive | Negative terminal of the voltage-doubler charge-pump capacitor. |
| 5 | C2+ | passive | Positive terminal of the inverting charge-pump capacitor. |
| 6 | C2- | passive | Negative terminal of the inverting charge-pump capacitor. |
| 7 | V- | power_out | -5.5V supply generated by the charge pump. |
| 8 | R1IN | input | RS-232 receiver input, ESD protected to ±15kV (Human Body Model). |
| 9 | R1OUT | output | TTL/CMOS receiver output. |
| 10 | INVALID | output | Active-low valid signal detector output; a logic high indicates a valid RS-232 level is present on a receiver input. |
| 11 | T1IN | input | TTL/CMOS transmitter input with no pullup resistor; connect to GND or VCC if unused. |
| 12 | FORCEON | input | Active-high force-on input; drive high to override AutoShutdown Plus and keep transmitters and receivers on (FORCEOFF must be high). |
| 13 | T1OUT | output | RS-232 transmitter output, ESD protected to ±15kV (Human Body Model). |
| 14 | GND | power_in | Ground. |
| 15 | VCC | power_in | +3.0V to +5.5V single supply voltage. |
| 16 | FORCEOFF | input | Active-low force-off input; when low, transmitters are high impedance, charge pumps are shut down and receivers are active, overriding AutoShutdown Plus and FORCEON. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices Inc./Maxim Integrated |
| Package | TSSOP-16 |
| Category | Communication Interface Chip |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 3 | 5.5 | V | VCC = +3V to +5.5V, TA = TMIN to TMAX | 6 | |
| Operating temperature range (EE grade) | TA | -40 | 85 | °C | MAX32_ EE _ | 2 | |
| Supply voltage to GND | VCC | -0.3 | 6 | V | VCC to GND | 2 | |
| V+ to GND | V+ | -0.3 | 7 | V | V+ to GND (Note 1) | 2 | |
| V- to GND | V- | -7 | 0.3 | V | V- to GND (Note 1) | 2 | |
| V+ + /V-/ | 13 | V | V+ +/V-/ (Note 1) | 2 | |||
| Input voltage T_IN, FORCEON, FORCEOFF | -0.3 | 6 | V | to GND | 2 | ||
| Input voltage R_IN | -25 | 25 | V | to GND | 2 | ||
| Output voltage T_OUT | -13.2 | 13.2 | V | to GND | 2 | ||
| Storage temperature range | TSTG | -65 | 160 | °C | 2 | ||
| Lead temperature (soldering, 10s) | 300 | °C | soldering, 10s | 2 | |||
| Thermal resistance junction to ambient, single layer board | θJA | 106 | °C/W | 16-TSSOP (U16+1), single layer board | 2 | ||
| Thermal resistance junction to case, single layer board | θJC | 27 | °C/W | 16-TSSOP (U16+1), single layer board | 2 | ||
| Thermal resistance junction to ambient, four-layer board | θJA | 90 | °C/W | 16-TSSOP (U16+1), four-layer board | 2 | ||
| Thermal resistance junction to case, four-layer board | θJC | 27 | °C/W | 16-TSSOP (U16+1), four-layer board | 2 | ||
| Supply Current, AutoShutdown Plus | 1 | 10 | μA | FORCEON = GND, FORCEOFF = VCC, all R_IN idle, all T_IN idle | 6 | ||
| Supply Current, Shutdown | 1 | 10 | μA | FORCEOFF = GND | 6 | ||
| Supply Current, AutoShutdown Plus Disabled | 0.3 | 1 | mA | FORCEON = FORCEOFF = VCC, no load | 6 | ||
| Input Logic Threshold Low | 0.8 | V | T_IN, FORCEON, FORCEOFF | 6 | |||
| Input Logic Threshold High | 2 | V | T_IN, FORCEON, FORCEOFF, VCC = 3.3V | 6 | |||
| Input Logic Threshold High | 2.4 | V | T_IN, FORCEON, FORCEOFF, VCC = 5.0V | 6 | |||
| Transmitter Input Hysteresis | 0.5 | V | 6 | ||||
| Input Leakage Current | -1 | 0.01 | 1 | μA | T_IN, FORCEON, FORCEOFF | 6 | |
| Output Leakage Current R_OUT | -10 | 0.05 | 10 | μA | receivers disabled | 6 | |
| Output Voltage Low | 0.4 | V | IOUT = 1.6mA | 6 | |||
| Receiver Input Voltage Range | -25 | 25 | V | 6 | |||
| Input Threshold Low | 0.6 | 1.2 | V | TA = +25°C, VCC = 3.3V | 6 | ||
| Input Threshold Low | 0.8 | 1.5 | V | TA = +25°C, VCC = 5.0V | 6 | ||
| Input Threshold High | 1.5 | 2.4 | V | TA = +25°C, VCC = 3.3V | 6 | ||
| Input Threshold High | 1.8 | 2.4 | V | TA = +25°C, VCC = 5.0V | 6 | ||
| Input Hysteresis | 0.5 | V | 6 | ||||
| Input Resistance | 3 | 5 | 7 | kΩ | TA = +25°C | 6 | |
| Output Voltage Swing | -5 | 5.4 | V | All transmitter outputs loaded with 3kΩ to ground | 6 | ||
| Output Resistance | 300 | Ω | VCC = V+ = V- = 0V, transmitter outputs = ±2V | 6 | |||
| Output Short-Circuit Current | -60 | 60 | mA | 6 | |||
| Output Leakage Current transmitters | -25 | 25 | µA | VCC = 0V or 3V to 5.5V, VOUT = ±12V, Transmitters disabled | 6 | ||
| ESD IEC 1000-4-2 Air Discharge | -15 | 15 | kV | R_IN, T_OUT | 7 | ||
| ESD IEC 1000-4-2 Contact Discharge | -8 | 8 | kV | R_IN, T_OUT | 7 | ||
| ESD Human Body Model | -15 | 15 | kV | R_IN, T_OUT | 7 | ||
| Receiver Input Threshold to INVALID Output High, positive threshold | 2.7 | V | AutoShutdown Plus, Figure 4a | 7 | |||
| Receiver Input Threshold to INVALID Output High, negative threshold | -2.7 | V | AutoShutdown Plus, Figure 4a | 7 | |||
| Receiver Input Threshold to INVALID Output Low | -0.3 | 0.3 | V | Figure 4a | 7 | ||
| INVALID, READY Output Voltage Low | 0.4 | V | IOUT = -1.6mA | 7 | |||
| Receiver Threshold to INVALID High | tINVH | 1 | μs | VCC = 5V, Figure 4b | 7 | ||
| Receiver Threshold to INVALID Low | tINVL | 30 | μs | VCC = 5V, Figure 4b | 7 | ||
| Receiver or Transmitter Edge to Transmitters Enabled | tWU | 100 | μs | VCC = 5V, Figure 5b (Note 2) | 7 | ||
| Receiver or Transmitter Edge to Transmitters Shutdown | tAUTOSHDN | 15 | 30 | 60 | s | VCC = 5V, Figure 5b (Note 2) | 7 |
| Maximum Data Rate | 250 | kbps | RL = 3kΩ, CL = 1000pF, one transmitter switching | 8 | |||
| Receiver Propagation Delay tPHL and tPLH | tPHL, tPLH | 0.15 | μs | R_IN to R_OUT, CL = 150pF | 8 | ||
| Transmitter Skew | │tPHL - tPLH│ | 100 | ns | (Note 3) | 8 | ||
| Receiver Skew | │tPHL - tPLH│ | 50 | ns | 8 | |||
| Transition-Region Slew Rate | 6 | 30 | V/μs | VCC = 3.3V, TA = +25°C, RL = 3kΩ to 7kΩ, CL = 150pF to 1000pF, one transmitter switching | 8 |
CAD (KiCad official)
- Symbol:
MAX3226EEUE+ - Footprint:
Package_SO:TSSOP-16_4.4x5mm_P0.65mm - 3D model: TSSOP-16 (KiCad packages3D, STEP)
- 3D model files:
max3226eeue-etched.step/max3226eeue-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);max3226eeue.step/max3226eeue.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices Inc./Maxim Integrated datasheet (25 pp, sha256
8542587c6f3a36a5, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# MAX3226EEUE+
**Analog Devices Inc./Maxim Integrated** · RS232 ICs · TSSOP-16
MAX3226EEUE+ from Analog Devices Inc./Maxim Integrated, in a TSSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | READY | output | Active-high ready-to-transmit output that goes high when V- falls below -4V and the device is ready to transmit. |
| 2 | C1+ | passive | Positive terminal of the voltage-doubler charge-pump capacitor. |
| 3 | V+ | power_out | +5.5V supply generated by the charge pump. |
| 4 | C1- | passive | Negative terminal of the voltage-doubler charge-pump capacitor. |
| 5 | C2+ | passive | Positive terminal of the inverting charge-pump capacitor. |
| 6 | C2- | passive | Negative terminal of the inverting charge-pump capacitor. |
| 7 | V- | power_out | -5.5V supply generated by the charge pump. |
| 8 | R1IN | input | RS-232 receiver input, ESD protected to ±15kV (Human Body Model). |
| 9 | R1OUT | output | TTL/CMOS receiver output. |
| 10 | INVALID | output | Active-low valid signal detector output; a logic high indicates a valid RS-232 level is present on a receiver input. |
| 11 | T1IN | input | TTL/CMOS transmitter input with no pullup resistor; connect to GND or VCC if unused. |
| 12 | FORCEON | input | Active-high force-on input; drive high to override AutoShutdown Plus and keep transmitters and receivers on (FORCEOFF must be high). |
| 13 | T1OUT | output | RS-232 transmitter output, ESD protected to ±15kV (Human Body Model). |
| 14 | GND | power_in | Ground. |
| 15 | VCC | power_in | +3.0V to +5.5V single supply voltage. |
| 16 | FORCEOFF | input | Active-low force-off input; when low, transmitters are high impedance, charge pumps are shut down and receivers are active, overriding AutoShutdown Plus and FORCEON. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices Inc./Maxim Integrated |
| Package | TSSOP-16 |
| Category | Communication Interface Chip |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage | VCC | 3 | | 5.5 | V | VCC = +3V to +5.5V, TA = TMIN to TMAX | 6 |
| Operating temperature range (EE grade) | TA | -40 | | 85 | °C | MAX32_ _EE_ _ | 2 |
| Supply voltage to GND | VCC | -0.3 | | 6 | V | VCC to GND | 2 |
| V+ to GND | V+ | -0.3 | | 7 | V | V+ to GND (Note 1) | 2 |
| V- to GND | V- | -7 | | 0.3 | V | V- to GND (Note 1) | 2 |
| V+ + /V-/ | | | | 13 | V | V+ +/V-/ (Note 1) | 2 |
| Input voltage T_IN, FORCEON, FORCEOFF | | -0.3 | | 6 | V | to GND | 2 |
| Input voltage R_IN | | -25 | | 25 | V | to GND | 2 |
| Output voltage T_OUT | | -13.2 | | 13.2 | V | to GND | 2 |
| Storage temperature range | TSTG | -65 | | 160 | °C | | 2 |
| Lead temperature (soldering, 10s) | | | | 300 | °C | soldering, 10s | 2 |
| Thermal resistance junction to ambient, single layer board | θJA | | | 106 | °C/W | 16-TSSOP (U16+1), single layer board | 2 |
| Thermal resistance junction to case, single layer board | θJC | | | 27 | °C/W | 16-TSSOP (U16+1), single layer board | 2 |
| Thermal resistance junction to ambient, four-layer board | θJA | | | 90 | °C/W | 16-TSSOP (U16+1), four-layer board | 2 |
| Thermal resistance junction to case, four-layer board | θJC | | | 27 | °C/W | 16-TSSOP (U16+1), four-layer board | 2 |
| Supply Current, AutoShutdown Plus | | | 1 | 10 | μA | FORCEON = GND, FORCEOFF = VCC, all R_IN idle, all T_IN idle | 6 |
| Supply Current, Shutdown | | | 1 | 10 | μA | FORCEOFF = GND | 6 |
| Supply Current, AutoShutdown Plus Disabled | | | 0.3 | 1 | mA | FORCEON = FORCEOFF = VCC, no load | 6 |
| Input Logic Threshold Low | | | | 0.8 | V | T_IN, FORCEON, FORCEOFF | 6 |
| Input Logic Threshold High | | 2 | | | V | T_IN, FORCEON, FORCEOFF, VCC = 3.3V | 6 |
| Input Logic Threshold High | | 2.4 | | | V | T_IN, FORCEON, FORCEOFF, VCC = 5.0V | 6 |
| Transmitter Input Hysteresis | | | 0.5 | | V | | 6 |
| Input Leakage Current | | -1 | 0.01 | 1 | μA | T_IN, FORCEON, FORCEOFF | 6 |
| Output Leakage Current R_OUT | | -10 | 0.05 | 10 | μA | receivers disabled | 6 |
| Output Voltage Low | | | | 0.4 | V | IOUT = 1.6mA | 6 |
| Receiver Input Voltage Range | | -25 | | 25 | V | | 6 |
| Input Threshold Low | | 0.6 | | 1.2 | V | TA = +25°C, VCC = 3.3V | 6 |
| Input Threshold Low | | 0.8 | | 1.5 | V | TA = +25°C, VCC = 5.0V | 6 |
| Input Threshold High | | 1.5 | | 2.4 | V | TA = +25°C, VCC = 3.3V | 6 |
| Input Threshold High | | 1.8 | | 2.4 | V | TA = +25°C, VCC = 5.0V | 6 |
| Input Hysteresis | | | 0.5 | | V | | 6 |
| Input Resistance | | 3 | 5 | 7 | kΩ | TA = +25°C | 6 |
| Output Voltage Swing | | -5 | 5.4 | | V | All transmitter outputs loaded with 3kΩ to ground | 6 |
| Output Resistance | | 300 | | | Ω | VCC = V+ = V- = 0V, transmitter outputs = ±2V | 6 |
| Output Short-Circuit Current | | -60 | | 60 | mA | | 6 |
| Output Leakage Current transmitters | | -25 | | 25 | µA | VCC = 0V or 3V to 5.5V, VOUT = ±12V, Transmitters disabled | 6 |
| ESD IEC 1000-4-2 Air Discharge | | -15 | | 15 | kV | R_IN, T_OUT | 7 |
| ESD IEC 1000-4-2 Contact Discharge | | -8 | | 8 | kV | R_IN, T_OUT | 7 |
| ESD Human Body Model | | -15 | | 15 | kV | R_IN, T_OUT | 7 |
| Receiver Input Threshold to INVALID Output High, positive threshold | | | | 2.7 | V | AutoShutdown Plus, Figure 4a | 7 |
| Receiver Input Threshold to INVALID Output High, negative threshold | | -2.7 | | | V | AutoShutdown Plus, Figure 4a | 7 |
| Receiver Input Threshold to INVALID Output Low | | -0.3 | | 0.3 | V | Figure 4a | 7 |
| INVALID, READY Output Voltage Low | | | | 0.4 | V | IOUT = -1.6mA | 7 |
| Receiver Threshold to INVALID High | tINVH | | | 1 | μs | VCC = 5V, Figure 4b | 7 |
| Receiver Threshold to INVALID Low | tINVL | | | 30 | μs | VCC = 5V, Figure 4b | 7 |
| Receiver or Transmitter Edge to Transmitters Enabled | tWU | | | 100 | μs | VCC = 5V, Figure 5b (Note 2) | 7 |
| Receiver or Transmitter Edge to Transmitters Shutdown | tAUTOSHDN | 15 | 30 | 60 | s | VCC = 5V, Figure 5b (Note 2) | 7 |
| Maximum Data Rate | | 250 | | | kbps | RL = 3kΩ, CL = 1000pF, one transmitter switching | 8 |
| Receiver Propagation Delay tPHL and tPLH | tPHL, tPLH | | 0.15 | | μs | R_IN to R_OUT, CL = 150pF | 8 |
| Transmitter Skew | │tPHL - tPLH│ | | | 100 | ns | (Note 3) | 8 |
| Receiver Skew | │tPHL - tPLH│ | | | 50 | ns | | 8 |
| Transition-Region Slew Rate | | 6 | | 30 | V/μs | VCC = 3.3V, TA = +25°C, RL = 3kΩ to 7kΩ, CL = 150pF to 1000pF, one transmitter switching | 8 |
## CAD (KiCad official)
- Symbol: `MAX3226EEUE+`
- Footprint: `Package_SO:TSSOP-16_4.4x5mm_P0.65mm`
- 3D model: TSSOP-16 (KiCad packages3D, STEP)
- 3D model files: `max3226eeue-etched.step` / `max3226eeue-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `max3226eeue.step` / `max3226eeue.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices Inc./Maxim Integrated datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/max3224e-max3245e.pdf) (25 pp, sha256 `8542587c6f3a36a5`, retrieved 2026-10-28, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/max3226eeue-datasheet.pdf)