main
Ray Publish 0.1.0 0354614

MAX17502GATB+T

Maxim Integrated · DC-DC Converters · TDFN-10-EP(2x3)

MAX17502GATB+T from Maxim Integrated, in a TDFN-10-EP(2x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 PGND power_in Power ground; connect externally to the power ground plane and tie GND and PGND together at the return of the VCC bypass capacitor.
2 VIN power_in Power-supply input with an operating range of 4.5V to 60V (absolute maximum VIN to GND is 70V).
3 EN/UVLO input Enable and undervoltage-lockout input; drive high to enable the output, use a resistor divider from VIN to GND to set the turn-on voltage, or pull up to VIN for always on.
4 VCC power_out 5V LDO output that must be bypassed with 1µF ceramic capacitance to GND.
5 FB/VO input Feedback input; connect directly to the output for fixed 3.3V/5V versions, or to the center of a resistor divider between VOUT and GND for the adjustable version.
6 SS passive Soft-start input; a capacitor from SS to GND sets the soft-start time.
7 N.C./COMP passive External loop compensation; for the adjustable MAX17502G/H connect an RC network from COMP to GND, and for the fixed MAX17502E/F leave it unconnected (N.C.).
8 RESET output Open-drain power-good output that is driven low when FB drops below 92.5% of its set value and goes high 1024 clock cycles after FB rises above 95.5%; it requires an external pullup and can sink 2mA while low.
9 GND power_in Analog ground; the GND pin must also be connected to the exposed pad.
10 LX output Switching node connected to the switching side of the inductor; high impedance in shutdown mode.
11 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Maxim Integrated
Package TDFN-10-EP(2x3)
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Voltage Range VIN 4.5 60 V 2
Input Supply Current, shutdown IIN-SH 0.9 3.5 µA VEN = 0V, shutdown mode 2
Input Supply Current, normal switching IIN-SW 4.75 6.75 mA Normal switching mode, no load; MAX17502E/F/G 2
EN Threshold, rising VENR 1.194 1.218 1.236 V VEN rising 2
EN Threshold, falling VENF 1.114 1.135 1.156 V VEN falling 2
EN True Shutdown Threshold VEN-TRUESD 0.7 V VEN falling, true shutdown 2
EN Input Leakage Current IEN 8 200 nA VEN = VIN = 60V, TA = +25°C 2
VCC Output Voltage Range VCC 4.65 5 5.35 V 6V < VIN < 12V, 0mA < IVCC < 10mA, 12V < VIN < 60V, 0mA < IVCC < 2mA 2
VCC Current Limit IVCC-MAX 15 40 80 mA VCC = 4.3V, VIN = 12V 2
VCC Dropout VCC-DO 4.1 V VIN = 4.5V, IVCC = 5mA 2
VCC UVLO Rising VCC-UVR 3.85 4 4.15 V VCC rising 2
VCC UVLO Falling VCC-UVF 3.55 3.7 3.85 V VCC falling 2
High-Side pMOS On-Resistance RDS-ONH 0.55 0.85 Ω ILX = 0.5A (sourcing), TA = +25°C 3
High-Side pMOS On-Resistance RDS-ONH 1.2 Ω ILX = 0.5A (sourcing), TA = TJ = +125°C (Note 3) 3
Low-Side nMOS On-Resistance RDS-ONL 0.2 0.35 Ω ILX = 0.5A (sinking), TA = +25°C 3
Low-Side nMOS On-Resistance RDS-ONL 0.47 Ω ILX = 0.5A (sinking), TA = TJ = +125°C (Note 3) 3
LX Leakage Current ILX_LKG 1 µA VEN = 0V, TA = +25°C, VLX = (VPGND + 1V) to (VIN - 1V) 3
Soft-Start Charging Current ISS 4.7 5 5.3 µA VSS = 0.5V 3
FB Input Bias Current IFB 100 nA TA = +25°C, MAX17502G/H, VFB = 0.9V 3
Output Voltage Range (adjustable) VOUT 0.9 V MAX17502G; maximum printed as 0.92 x VIN 3
Transconductance GM 510 590 650 µS ICOMP = ±2.5µA, MAX17502G/H 3
COMP Source Current ICOMP_SRC 19 32 55 µA MAX17502G/H 3
COMP Sink Current ICOMP_SINK 19 32 55 µA MAX17502G/H 3
Current-Sense Transresistance RCS 0.45 0.5 0.55 V/A MAX17502G/H 3
Peak Current-Limit Threshold IPEAK-LIMIT 1.4 1.65 1.9 A 4
Runaway Current-Limit Threshold IRUNAWAY-LIMIT 1.45 1.7 2 A 4
Sink Current-Limit Threshold ISINK-LIMIT 0.56 0.65 0.74 A MAX17502E/F/G/H 4
Switching Frequency fSW 560 600 640 kHz VFB > VOUT-HICF, MAX17502E/F/G 4
Switching Frequency (foldback) fSW 280 300 320 kHz VFB < VOUT-HICF 4
VOUT Undervoltage Trip Level to Cause Hiccup VOUT-HICF 69.14 71.14 73.14 % VSS > 0.95V (soft-start is done) 4
Minimum On-Time tON_MIN 75 120 ns 4
Maximum Duty Cycle DMAX 92 94 96 % VFB = 0.98 x VFB-REG, MAX17502E/F/G 4
RESET Output Level Low 0.02 V IRESET = 1mA 4
RESET Output Leakage Current High 0.45 µA VFB = 1.01 x VFB-REG, TA = +25°C 4
VOUT Threshold for RESET Falling VOUT-OKF 90.5 92.5 94.5 % VFB falling 4
VOUT Threshold for RESET Rising VOUT-OKR 93.5 95.5 97.5 % VFB rising 4
Absolute Max Input Voltage VIN to GND VIN -0.3 70 V VIN to GND 2
EN/UVLO to GND EN/UVLO -0.3 V EN/UVLO to GND; maximum printed as VIN + 0.3V 2
LX to PGND LX -0.3 V LX to PGND; maximum printed as VIN + 0.3V 2
FB, RESET, COMP, SS to GND FB, RESET, COMP, SS -0.3 6 V to GND 2
VCC to GND VCC -0.3 6 V to GND 2
GND to PGND GND-PGND -0.3 0.3 V 2
LX Total RMS Current LX -1.6 1.6 A 2
Junction Temperature TJ 150 °C 2
Storage Temperature Range TSTG -65 160 °C 2
Lead Temperature (soldering, 10s) 300 °C soldering, 10s 2
Soldering Temperature (reflow) 260 °C reflow 2
Ambient Operating Temperature TA -40 125 °C 1
Junction Operating Temperature TJ -40 150 °C 1
Thermal-Shutdown Threshold 165 °C Temperature rising 4
Thermal-Shutdown Hysteresis 10 °C 4
LX Dead Time 5 ns 4
HICCUP Timeout 32768 cycles printed as 32,768 cycles 4
RESET Delay After FB Reaches 95% Regulation 1024 cycles VFB rising 4

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper , EP Exposed Pad. Connect to the GND pin of the IC. Connect to a large copper plane below the IC 9

CAD (KiCad official)

  • Symbol: MAX17502GATB+T
  • Footprint: Package_DFN_QFN:DFN-10-1EP_2x3mm_P0.5mm_EP0.64x2.4mm
  • 3D model: TDFN-10-EP(2x3) (KiCad packages3D, STEP)
  • 3D model files: max17502gatb-t-etched.step / max17502gatb-t-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); max17502gatb-t.step / max17502gatb-t.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Maxim Integrated datasheet (21 pp, sha256 a4385054b0b515b7, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF