MAL216099702E3 - 100 uF 80 V SMD Aluminium Electrolytic Capacitor, 150 C

{
 "plan": {
  "schema": "adom/mark-plan@1",
  "mpn": "MAL216099702E3",
  "step": "/home/adom/project/uta-dynos/work/pages/mal216099702e3/work/etch/mal216099702e3.step",
  "footprint": "/home/adom/project/uta-dynos/work/pages/mal216099702e3/work/etch/mal216099702e3.kicad_mod",
  "standUp": [],
  "standUpSource": "--up z",
  "inputs": {
   "up": "z",
   "face": "top",
   "along": "y",
   "upSupplied": true,
   "faceSupplied": true,
   "faceSource": "--face top"
  },
  "face": "top",
  "pin1": {
   "source": "footprint pad 1",
   "xyMm": [
    -5.15,
    -0.0
   ],
   "corner": "centre/lower"
  },
  "existingMarks": [],
  "vendorMarking": {
   "present": true,
   "glyphFaces": 8
  },
  "faceNormal": [
   0,
   0,
   1
  ],
  "longAxis": {
   "axis": "y",
   "vector": [
    0.0,
    1.0,
    0.0
   ],
   "why": "square body: along the pin-1 row",
   "source": "pin-1-row",
   "override": "y",
   "pinRows": null
  },
  "readingDirection": {
   "vector": [
    -0.0,
    -1.0,
    0.0
   ],
   "angleDeg": 270,
   "textUp": [
    1.0,
    -0.0,
    0.0
   ],
   "rule": "pin 1 / pad 1 at the start (left) of the text, and below it when it sits on a side"
  },
  "band": {
   "regionMm": [
    -5.65,
    -5.65,
    5.65,
    5.65
   ],
   "zMm": 16.0,
   "lengthMm": 11.3,
   "heightMm": 11.3,
   "why": "highest flat face over the body centre",
   "terminationsExcludedBy": null,
   "trimmedEnds": [],
   "keepouts": [],
   "sideTurn": null,
   "margins": {
    "lengthEachSide": 0.12,
    "heightEachSide": 0.15
   }
  },
  "text": {
   "lines": [
    "MAL",
    "216099702E3"
   ],
   "chars": 14,
   "capHeightMm": 0.9715,
   "smallestLineMm": 0.9715,
   "heightPctOfBand": 19.8,
   "why": "two lines: the smaller line (0.972 mm) beats one line (0.760 mm) by 1.28x",
   "alternative": {
    "lines": [
     "MAL216099702E3"
    ],
    "capHeightMm": 0.76,
    "smallestLineMm": 0.76
   },
   "font": "service-step2glb /laser-etch (single-stroke outline font)"
  },
  "etch": {
   "poseQuarterTurnsZ": 1,
   "service": "/laser-etch?mode=flat",
   "note": "turn so the reading direction is +X, etch, fit the mark into the band, turn back"
  },
  "outline": {
   "upAxis": "z",
   "poseRotZDeg": 180,
   "rot": 90,
   "recipe": "adom-aiflow-etch outline <part.step> --footprint <part.kicad_mod> --mpn MAL216099702E3 (stands the STEP up (--up z), turns it 180 deg about Z and draws MAL / 216099702E3 on the planned band, rot 90)",
   "why": "iso camera looks from +X+Y+Z: text along +Y (rot 90) or -X (rot 180) reads left to right with pin 1 toward the viewer"
  },
  "widget": {
   "px": 320,
   "pxPerMm": 12.18,
   "capHeightPx": 9.7
  },
  "hints": [],
  "warnings": [
   "the vendor model already carries a printed marking (8 glyph faces on the top): keep the vendor model and do not etch over it (adom-aiflow-etch refuses unless --over-vendor-mark)",
   "--along y puts the text across the short side (11.30 mm instead of 11.30 mm); only do this to keep a polarity stripe or printed band clear"
  ],
  "summary": "Mark along the 11.30 mm axis (-Y), 0.97 mm text (2 lines), upright with pin 1 centre lower, outline rot 90 after a 180 deg pose turn; ~10 px caps at 320 px"
 },
 "etch": {
  "out": "/home/adom/project/uta-dynos/work/pages/mal216099702e3/work/etch/mal216099702e3-etched.step",
  "mpn": "MAL216099702E3",
  "lines": [
   "MAL2160",
   "99702E3"
  ],
  "removedOldMarks": [],
  "turns": [
   {
    "axis": "z",
    "quarterTurns": 1
   }
  ],
  "serviceMarkTurnedQuarter": 3,
  "line2Scaled": true,
  "fit": {
   "scale": 0.8748,
   "capMm": 1.507,
   "markMm": [
    8.588,
    3.5374
   ],
   "bandMm": [
    11.3,
    11.3
   ],
   "zMm": 16.005
  }
 }
}