Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

M95M01-DWDW3TP

The maker sells this part only as M95M01-DWDW3TP/K (ST ordering information scheme: "T = Tape and reel packing", "/K = Manufacturing technology code"; the bare code lacks the process letter (Table 18, p.38)). The DigiKey and Mouser numbers on this page are for M95M01-DWDW3TP/K.

STMicroelectronics · EEPROM · TSSOP-8

M95M01-DWDW3TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 S input Chip Select: driving it low selects the device and starts communication, driving it high deselects the device and puts Q in high impedance.
2 Q tri_state Serial Data output: shifts data out on the falling edge of C, MSB first, and is high impedance in all other cases.
3 W input Write Protect: used to write-protect the Status Register.
4 VSS power_in Ground: the reference for all signals, including the VCC supply voltage.
5 D input Serial Data input: receives instructions, addresses and data to be written, latched on the rising edge of C, MSB first.
6 C input Serial Clock: synchronizes the serial interface, with inputs latched on the rising edge and Q changing after the falling edge.
7 HOLD input Hold: pauses serial communication with the device without deselecting it or resetting the clocking sequence.
8 VCC power_in Supply voltage: 2.5 V to 5.5 V for the W voltage range, with a 10 nF to 100 nF decoupling capacitor recommended close to the VCC/VSS pins.

Key specifications

Parameter Value
Manufacturer STMicroelectronics
Package TSSOP-8
Category Memory
Pins 8

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Storage temperature TSTG -65 150 °C 29
Ambient operating temperature (absolute maximum ratings) TAMR -40 150 °C 29
Voltage on Q pin VO -0.5 V 29
Input voltage VI -0.5 6.5 V 29
DC output current (Q = 0) IOL 5 mA Q = 0 29
DC output current (Q = 1) IOH 5 mA Q = 1 29
Supply voltage (absolute maximum) VCC -0.5 6.5 V 29
Electrostatic pulse (Human Body Model) VESD 4000 V 29
Write cycle endurance Ncycle 4e+06 TA ≤ 25 °C, 2.5 V < VCC < 5.5 V 30
Write cycle endurance Ncycle 1.2e+06 TA = 85 °C, 2.5 V < VCC < 5.5 V 30
Write cycle endurance Ncycle 600000 TA = 125 °C, 2.5 V < VCC < 5.5 V 30
Supply voltage (temperature range 3, Table 11) VCC 2.5 5.5 V 30
Ambient operating temperature (temperature range 3, Table 11) TA -40 125 °C 30
Operating clock frequency (Table 11) fC 10 MHz VCC ≥ 2.5 V, capacitive load on Q pin ≤100pF 30
Supply voltage (high-speed, Table 12) VCC 4.5 5.5 V 30
Ambient operating temperature (high-speed, Table 12) TA -40 85 °C 30
Operating clock frequency (high-speed, Table 12) fC 16 MHz VCC ≥ 4.5 V, capacitive load on Q pin ≤60 pF 30
Output capacitance (Q) COUT 8 pF VOUT = 0 V 32
Input capacitance CIN 6 pF VIN = 0 V 32
Input leakage current ILI 2 µA VIN = VSS or VCC 32
Output leakage current ILO 3 µA S = VCC, VOUT = VSS or VCC 32
Supply current (Read) ICC 2 mA VCC = 2.5 V, C = 0.1VCC/0.9 VCC, Q = open fC = 10 MHz 32
Supply current (Read) ICC 5 mA VCC = 5.5 V, fC = 16 MHz, C = 0.1 VCC/0.9 VCC, Q = open; -40 °C < t° < 85 °C 32
Supply current (Write) ICC0 2 mA 2.5 V ≤ VCC < 5.5 V during tW, S = VCC 32
Supply current (Standby mode) ICC1 2 µA t° = 85 °C, VCC = 2.5 V, S = VCC, VIN = VSS or VCC 32
Supply current (Standby mode) ICC1 3 µA t° = 85 °C, VCC = 5.5 V, S = VCC, VIN = VSS or VCC 32
Supply current (Standby mode) ICC1 15 µA t° = 125 °C, VCC = 2.5 V, S = VCC, VIN = VSS or VCC 32
Supply current (Standby mode) ICC1 20 µA t° = 125 °C, VCC = 5.5 V, S = VCC, VIN = VSS or VCC 32
Input low voltage (min) VIL -0.45 V 2.5 V ≤ VCC < 5.5 V 32
Input low voltage (max, × VCC) VIL 0.3 VCC 2.5 V ≤ VCC < 5.5 V 32
Input high voltage (min, × VCC) VIH 0.7 VCC 2.5 V ≤ VCC < 5.5 V 32
Output low voltage VOL 0.4 V VCC ≥ 2.5 V, IOL = 2 mA 32
Output high voltage (min, × VCC) VOH 0.8 VCC VCC ≥ 2.5 V, IOH = -2 mA 32
Internal reset threshold voltage VRES 0.5 1.5 V 32
S active setup time tSLCH 30 ns Test conditions specified in Table 10 and Table 11 33
S not active setup time tSHCH 30 ns Test conditions specified in Table 10 and Table 11 33
S deselect time tSHSL 40 ns Test conditions specified in Table 10 and Table 11 33
S active hold time tCHSH 30 ns Test conditions specified in Table 10 and Table 11 33
S not active hold time tCHSL 30 ns Test conditions specified in Table 10 and Table 11 33
Clock high time tCH 40 ns Test conditions specified in Table 10 and Table 11 33
Clock low time tCL 40 ns Test conditions specified in Table 10 and Table 11 33
Data in setup time tDVCH 10 ns Test conditions specified in Table 10 and Table 11 33
Data in hold time tCHDX 10 ns Test conditions specified in Table 10 and Table 11 33
Clock low hold time after HOLD not active tHHCH 30 ns Test conditions specified in Table 10 and Table 11 33
Clock low hold time after HOLD active tHLCH 30 ns Test conditions specified in Table 10 and Table 11 33
Clock low set-up time before HOLD active tCLHL 0 ns Test conditions specified in Table 10 and Table 11 33
Clock low set-up time before HOLD not active tCLHH 0 ns Test conditions specified in Table 10 and Table 11 33
Output disable time tSHQZ 40 ns Test conditions specified in Table 10 and Table 11 33
Clock low to output valid tCLQV 40 ns Test conditions specified in Table 10 and Table 11 33
Output hold time tCLQX 0 ns Test conditions specified in Table 10 and Table 11 33
HOLD high to output valid tHHQV 40 ns Test conditions specified in Table 10 and Table 11 33
HOLD low to output high-Z tHLQZ 40 ns Test conditions specified in Table 10 and Table 11 33
Write time tW 4 ms Test conditions specified in Table 10 and Table 11 33

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts tin TLEAD Lead temperature during soldering See note (1) 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST ECOPACK® 29

CAD (KiCad official)

  • Symbol: M95M01-DWDW3TP
  • Footprint: Package_SO:TSSOP-8_4.4x3mm_P0.65mm
  • 3D model: TSSOP-8 (KiCad packages3D, STEP)
  • 3D model files: m95m01-dwdw3tp-etched.step / m95m01-dwdw3tp-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); m95m01-dwdw3tp.step / m95m01-dwdw3tp.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: STMicroelectronics datasheet (40 pp, sha256 9497f4a9c0dcdee7, retrieved 2026-11-12, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF