Generated by kicad-footprint-generator · KiCad file format 20260206
M95320-RDW6TP
STMicroelectronics · EEPROM · TSSOP-8
M95320-RDW6TP from STMicroelectronics, in a TSSOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | S | input | Chip Select: the device is selected when S is driven low and deselected when high, with Serial Data Output (Q) at high impedance; S must follow VCC during power-up and a falling edge is required before the first instruction. |
| 2 | Q | output | Serial Data Output: data is shifted out on the falling edge of Serial Clock (C), and Q is high impedance when the device is deselected or in the Hold condition. |
| 3 | W | input | Write Protect: must be driven either high or low and must be stable during all Write instructions; with SRWD set to 1 and W low, the Status Register becomes hardware write-protected. |
| 4 | VSS | power_in | Ground: the reference for all signals, including the VCC supply voltage. |
| 5 | D | input | Serial Data Input: receives instructions, addresses and data to be written, latched on the rising edge of Serial Clock (C). |
| 6 | C | input | Serial Clock: provides the serial interface timing, with inputs latched on its rising edge and Q changing from its falling edge; maximum clock frequency is 20 MHz for VCC 4.5 V to 5.5 V (Table 18). |
| 7 | HOLD | input | Hold: when driven low while the device is selected (S low) and C is low, it pauses serial communication without deselecting the device, with Q high impedance and D and C as don't care. |
| 8 | VCC | power_in | Supply voltage: must stay within the specified range during operation, 1.8 V to 5.5 V for the M95320-R (Table 9), and be decoupled close to the VCC/VSS pins with 10 nF to 100 nF. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | STMicroelectronics |
| Package | TSSOP-8 |
| Category | Memory |
| Pins | 8 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input leakage current | ILI | -2 | 2 | µA | VIN = VSS or VCC | 36 | |
| Output leakage current | ILO | -2 | 2 | µA | S = VCC, voltage applied on Q = VSS or VCC | 36 | |
| Supply current (Read) | ICC | 2 | mA | VCC = 1.8 V, max clock frequency (fC), C = 0.1VCC/0.9VCC, Q = open | 36 | ||
| Supply current (Write) | ICC0 | 5 | mA | VCC = 1.8 V, during tW, S = VCC | 36 | ||
| Supply current (Standby) | ICC1 | 1 | µA | VCC = 1.8 V, S = VCC, VIN = VSS or VCC | 36 | ||
| Input low voltage | VIL | -0.45 | V | 1.8 V ≤ VCC < 2.5 V; printed max is 0.25 VCC | 36 | ||
| Output low voltage | VOL | 0.3 | V | IOL = 0.15 mA, VCC = 1.8 V | 36 | ||
| Internal reset threshold voltage | VRES | 1 | 1.65 | V | 36 | ||
| Supply voltage | VCC | 1.8 | 5.5 | V | M95320-R, device grade 6 | 33 | |
| Ambient operating temperature | TA | -40 | 85 | °C | M95320-R, device grade 6 | 33 | |
| Ambient operating temperature | -40 | 130 | °C | 32 | |||
| Storage temperature | TSTG | -65 | 150 | °C | 32 | ||
| Output voltage | VO | -0.5 | V | printed max is VCC+0.6 | 32 | ||
| Input voltage | VI | -0.5 | 6.5 | V | 32 | ||
| Supply voltage | VCC | -0.5 | 6.5 | V | 32 | ||
| DC output current (Q = 0) | IOL | 5 | mA | Q = 0 | 32 | ||
| DC output current (Q = 1) | IOH | 5 | mA | Q = 1 | 32 | ||
| Electrostatic discharge voltage (human body model) | VESD | 4000 | V | Human body model, AEC-Q100-002 | 32 | ||
| Output capacitance (Q) | COUT | 8 | pF | VOUT = 0 V | 34 | ||
| Input capacitance (D) | CIN | 8 | pF | VIN = 0 V | 34 | ||
| Input capacitance (other pins) | CIN | 6 | pF | VIN = 0 V | 34 | ||
| Write cycle endurance | Ncycle | 4e+06 | Write cycle | TA ≤ 25 °C, VCC(min) < VCC < VCC(max) | 34 | ||
| Write cycle endurance | Ncycle | 1.2e+06 | Write cycle | TA = 85 °C, VCC(min) < VCC < VCC(max) | 34 | ||
| Data retention | 200 | Year | TA = 55 °C | 34 | |||
| Clock frequency | fC | 5 | MHz | Test conditions specified in Table 9 and Table 11 | 39 | ||
| S active setup time | tSLCH | 60 | ns | Test conditions specified in Table 9 and Table 11 | 39 | ||
| S not active setup time | tSHCH | 60 | ns | Test conditions specified in Table 9 and Table 11 | 39 | ||
| S deselect time | tSHSL | 90 | ns | Test conditions specified in Table 9 and Table 11 | 39 | ||
| S active hold time | tCHSH | 60 | ns | Test conditions specified in Table 9 and Table 11 | 39 | ||
| S not active hold time | tCHSL | 60 | ns | Test conditions specified in Table 9 and Table 11 | 39 | ||
| Clock high time | tCH | 90 | ns | Test conditions specified in Table 9 and Table 11 | 39 | ||
| Clock low time | tCL | 90 | ns | Test conditions specified in Table 9 and Table 11 | 39 | ||
| Clock rise time | tCLCH | 2 | µs | Test conditions specified in Table 9 and Table 11; characterized only | 39 | ||
| Clock fall time | tCHCL | 2 | µs | Test conditions specified in Table 9 and Table 11; characterized only | 39 | ||
| Data in setup time | tDVCH | 20 | ns | Test conditions specified in Table 9 and Table 11 | 39 | ||
| Data in hold time | tCHDX | 20 | ns | Test conditions specified in Table 9 and Table 11 | 39 | ||
| Clock low hold time after HOLD not active | tHHCH | 60 | ns | Test conditions specified in Table 9 and Table 11 | 39 | ||
| Clock low hold time after HOLD active | tHLCH | 60 | ns | Test conditions specified in Table 9 and Table 11 | 39 | ||
| Clock low set-up time before HOLD active | tCLHL | 0 | ns | Test conditions specified in Table 9 and Table 11 | 39 | ||
| Clock low set-up time before HOLD not active | tCLHH | 0 | ns | Test conditions specified in Table 9 and Table 11 | 39 | ||
| Output disable time | tSHQZ | 80 | ns | Test conditions specified in Table 9 and Table 11; characterized only | 39 | ||
| Clock low to output valid | tCLQV | 80 | ns | Test conditions specified in Table 9 and Table 11 | 39 | ||
| Output hold time | tCLQX | 0 | ns | Test conditions specified in Table 9 and Table 11 | 39 | ||
| Output rise time | tQLQH | 80 | ns | Test conditions specified in Table 9 and Table 11; characterized only | 39 | ||
| Output fall time | tQHQL | 80 | ns | Test conditions specified in Table 9 and Table 11; characterized only | 39 | ||
| HOLD high to output valid | tHHQV | 80 | ns | Test conditions specified in Table 9 and Table 11 | 39 | ||
| HOLD low to output high-Z | tHLQZ | 80 | ns | Test conditions specified in Table 9 and Table 11; characterized only | 39 | ||
| Write time | tW | 5 | ms | Test conditions specified in Table 9 and Table 11 | 39 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | tin | TLEAD Lead temperature during soldering See note (1) 1. Compliant with JEDEC standard J-STD-020D (for small-body, Sn-Pb or Pb free assembly), the ST | 32 |
CAD (KiCad official)
- Symbol:
M95320-RDW6TP - Footprint:
Package_SO:TSSOP-8_4.4x3mm_P0.65mm - 3D model: TSSOP-8 (KiCad packages3D, STEP)
- 3D model files:
m95320-rdw6tp-etched.step/m95320-rdw6tp-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);m95320-rdw6tp.step/m95320-rdw6tp.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: STMicroelectronics datasheet (48 pp, sha256
4f1e68c8bd4605a5, retrieved 2026-11-10, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).