← Commit history

Initial commit: component/m95256-wmn6p

Ray ·1ed171fd5b ·
2 files changed +203
README.mdadded+44
@@ -0,0 +1,44 @@+# M95256-WMN6P++**STMicroelectronics** · EEPROM · SO-8++M95256-WMN6P from STMicroelectronics, in a SO-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.++## Pinout++| Pin | Name | Type | Function |+|---|---|---|---|+| 1 | S | input | Chip Select, active low: high deselects the device and puts Q in high impedance (Standby unless a Write cycle is in progress), low selects it (Active Power mode); a falling edge is required after power-up before any instruction. |+| 2 | Q | tri_state | Serial Data Output, shifts data out on the falling edge of Serial Clock (C) and is high impedance when deselected or during the Hold condition. |+| 3 | W | input | Write Protect, active low: freezes the size of the memory area protected by the BP1 and BP0 bits of the Status Register, must be driven high or low and stable during all Write instructions. |+| 4 | VSS | power_in | Ground, the reference for all signals including the VCC supply voltage. |+| 5 | D | input | Serial Data Input, receives instructions, addresses and data to be written, latched on the rising edge of Serial Clock (C). |+| 6 | C | input | Serial Clock, provides the timing of the serial interface; inputs are latched on the rising edge and Q changes from the falling edge, with a maximum frequency of 20 MHz. |+| 7 | HOLD | input | Hold, active low: pauses serial communication without deselecting the device; during Hold Q is high impedance and D and C are Don't Care. |+| 8 | VCC | power_in | Supply voltage, 2.5 V to 5.5 V for M95256-W, which must be stable and valid during operation and write cycles; decouple with 10 nF to 100 nF close to the VCC/VSS pins. |++## Key specifications++| Parameter | Value |+|---|---|+| Manufacturer | STMicroelectronics |+| Package | SO-8 |+| Category | Memory |+| Pins | 8 |++## CAD (KiCad official)++- Symbol: `M95256-WMN6P`+- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`+- 3D model: SO-8 (KiCad packages3D, STEP)+- 3D model files: `m95256-wmn6p-etched.step` / `m95256-wmn6p-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `m95256-wmn6p.step` / `m95256-wmn6p.glb` are the bare package body.++## Provenance++Data extracted from the manufacturer datasheet, not a distributor listing:++- **Datasheet:** [STMicroelectronics datasheet](https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588910167404785664) (57 pp, sha256 `698166e3207620a0`, retrieved 2026-09-29, tier: lcsc)+- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-4-5-20251001` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.+- **CAD:** KiCad official libraries (CC-BY-SA 4.0).++[Datasheet PDF](docs/m95256-wmn6p-datasheet.pdf)
page.jsonadded+159
@@ -0,0 +1,159 @@+{+  "slug": "m95256-wmn6p",+  "version": "0.1.0",+  "type": "component",+  "description": "STMicroelectronics EEPROM, SO-8. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.",+  "tags": [+    "component",+    "memory",+    "m95256-wmn6p",+    "factory-2.0.0",+    "extractor-text"+  ],+  "dependencies": {},+  "hero": {+    "type": "image",+    "path": "docs/hero.png"+  },+  "files": [+    "page.json",+    "README.md",+    "m95256-wmn6p.kicad_sym",+    "m95256-wmn6p.kicad_mod",+    "m95256-wmn6p.glb",+    "m95256-wmn6p.step",+    "m95256-wmn6p.lbr",+    "docs/hero.png",+    "docs/m95256-wmn6p-datasheet.pdf",+    "viewers/symbol.html",+    "viewers/footprint.html"+  ],+  "component": {+    "mpn": "M95256-WMN6P",+    "manufacturer": "STMicroelectronics",+    "package": "SO-8",+    "pin_count": 8,+    "category": "Memory",+    "subcategory": "EEPROM",+    "datasheet": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588910167404785664",+    "parts": {+      "symbol": "m95256-wmn6p.kicad_sym",+      "footprint": "m95256-wmn6p.kicad_mod",+      "model_3d": "m95256-wmn6p-etched.glb",+      "model_3d_plain": "m95256-wmn6p.glb",+      "model_3d_step": "m95256-wmn6p-etched.step",+      "model_3d_step_plain": "m95256-wmn6p.step",+      "lbr": "m95256-wmn6p.lbr"+    },+    "distributor_links": {+      "lcsc": "C222231",+      "digikey": "497-6357-5-ND",+      "mouser": "511-M95256-WMN6P"+    },+    "distributor_check": {+      "checked_at": "2026-09-29T23:01:07Z",+      "source": "Component Ocean /api/assign-pns",+      "digikey": {+        "pn": "497-6357-5-ND",+        "status": "found",+        "lifecycle": "Active"+      },+      "mouser": {+        "pn": "511-M95256-WMN6P",+        "status": "found",+        "lifecycle": "Not Recommended for New Designs"+      }+    },+    "pins": [+      {+        "number": "1",+        "name": "S",+        "type": "input",+        "description": "Chip Select, active low: high deselects the device and puts Q in high impedance (Standby unless a Write cycle is in progress), low selects it (Active Power mode); a falling edge is required after power-up before any instruction."+      },+      {+        "number": "2",+        "name": "Q",+        "type": "tri_state",+        "description": "Serial Data Output, shifts data out on the falling edge of Serial Clock (C) and is high impedance when deselected or during the Hold condition."+      },+      {+        "number": "3",+        "name": "W",+        "type": "input",+        "description": "Write Protect, active low: freezes the size of the memory area protected by the BP1 and BP0 bits of the Status Register, must be driven high or low and stable during all Write instructions."+      },+      {+        "number": "4",+        "name": "VSS",+        "type": "power_in",+        "description": "Ground, the reference for all signals including the VCC supply voltage."+      },+      {+        "number": "5",+        "name": "D",+        "type": "input",+        "description": "Serial Data Input, receives instructions, addresses and data to be written, latched on the rising edge of Serial Clock (C)."+      },+      {+        "number": "6",+        "name": "C",+        "type": "input",+        "description": "Serial Clock, provides the timing of the serial interface; inputs are latched on the rising edge and Q changes from the falling edge, with a maximum frequency of 20 MHz."+      },+      {+        "number": "7",+        "name": "HOLD",+        "type": "input",+        "description": "Hold, active low: pauses serial communication without deselecting the device; during Hold Q is high impedance and D and C are Don't Care."+      },+      {+        "number": "8",+        "name": "VCC",+        "type": "power_in",+        "description": "Supply voltage, 2.5 V to 5.5 V for M95256-W, which must be stable and valid during operation and write cycles; decouple with 10 nF to 100 nF close to the VCC/VSS pins."+      }+    ],+    "provenance": {+      "extractor": "extract_pins 0.3",+      "factory_chain": {+        "factory": "2.0.0",+        "extractor": "extract_pins 0.3",+        "primary_model": "claude-haiku-4-5-20251001",+        "primary_mode": "text",+        "consensus_model": "claude-sonnet-5-5",+        "consensus": "agreed",+        "guards": "pin_guards 0.1: passed",+        "guard_notes": [+          "extractor flagged: Figure 2 (page 7) showing 8-pin package connections contains OCR-corrupted text rendering the diagra"+        ],+        "pages_sent": 26,+        "cost_usd": 0.5016,+        "at": "2026-09-29T23:00:50"+      },+      "datasheet": {+        "url": "https://jlcpcb.com/api/file/downloadByFileSystemAccessId/8588910167404785664",+        "pages": 57,+        "sha256": "698166e3207620a0",+        "source_tier": "lcsc"+      },+      "cad": "KiCad official (CC-BY-SA 4.0)",+      "pins": {+        "total": 8,+        "described": 8,+        "cites_pages": true,+        "refuses_to_fabricate": true+      }+    },+    "viewers": {+      "symbol": "viewers/symbol.html",+      "footprint": "viewers/footprint.html"+    }+  },+  "visibility": "public",+  "org": "adom",+  "author": {+    "name": "Ray",+    "email": "[email protected]"+  }+}\ No newline at end of file